1. Types of Maps & Remote Sensing

2. Biblical Reference As the men started on their way to map out the land, Joshua instructed them, “Go and make a survey of the land and write a description of it. Then return to me, and I will cast lots for you here at Shiloh in the presence of the Lord.” Joshua 18:8

3. Projections Cartographers use projections to make maps. –A projection is made by transferring points and lines on a globe’s surface onto a piece of paper. There are three main types of projections: GnomonicConicMercator

4. Mercator Projections A Mercator Projection is a map that has parallel lines of latitude and longitude. –It clearly indicates direction in straight lines. –It distorts areas near the poles. –It is used for ship and plane navigation. o Total area of Greenland = 836,300 square miles o Total area of the U.S. = 3,806,000 square miles

5. Conic Projections A Conic Projection is made by projecting points and lines from a globe onto a cone. –It has a high degree of accuracy for limited areas. –It is used to make road and weather maps.

6. Gnomonic Projections A Gnomonic Projection is created by projecting points and lines on a globe onto a piece of paper that touches the globe a single point. –It is most useful for navigation for planning a long travel route.

7. Topographic Maps Topographic maps are detailed maps that use contour lines, symbols and colors to represent changes in elevation and features on the Earth’s surface. –A contour line connects points of equal elevation. –The difference in elevation between two side-by-side contour lines is a contour interval.

8. Topographic Maps Index contours are numbered contour lines to indicate elevation. Depression contour lines have short lines at right angles to the contour line to indicate a change in the elevation direction.

9. Geologic Maps A geologic map shows the distribution, arrangement and type of rocks located below the soil. –It may also show geologic features, such as fault lines.

10. Three-Dimensional Maps Computers are often used to digitize features such as rivers, mountains, valley and hills in order to create three-dimensional maps.

11. Map Legends A map legend explains what the symbols on a map represent. Symbols can represent: –Physical features (lakes, rivers or contours) –Roadways (interstates, highways, railroads) –Populated areas (city sizes, state capitals)

12. Map Scales A map scale is a ratio between the distance on a map and the actual distance. –Graphic scales, the most common, are lines that represent certain distances. –Verbal scales are statements used to express distance (“One centimeter equals one kilometer”) –Fractional scales express distance as a ratio between two units of the same type (1:1000 km). Maps

13. A.1:20,000 miles B.1:40,000 miles C.1:60,000 miles D.1:80,000 miles Which fractional scale represents the large actual distance? Pop Quiz

14. A.Different surface temperatures B.Different types of rock formations C.Different geologic terrain D.Different elevations What do different colors on a geologic map represent? Pop Quiz

15. A.Never B.At a mountain top C.At a valley D.At sea level When do contour lines cross? Pop Quiz

16. Gaspard Felix Tournachon

17. Remote Sensing In Remote Sensing instruments mounted on aircraft, satellites or balloons gather data about Earth. Landsat satellites record reflected visible and IR wavelengths from Earth’s surface. –A computer converts the data into digital images. –Landsat data are also used to study Earth’s plate movements, rivers, earthquakes and pollution.

18. Landsat 6 Landsat 6 was launched October 5, 1993 aboard a Titan II launch vehicle. It failed to reach orbit due to a ruptured fuel line.

19. TOPEX/Poseidon The TOPEX/Poseidon satellite uses radar to map seafloor features. –It transmits high frequency signals to the ocean floor. –A receiving device picks up the reflected echo. –The distance is calculated using the known speed of light (through air and sea water) and the time it takes for the round trip.

20. TOPEX/Poseidon Scientists also use TOPEX/Poseidon to estimate global sea levels, and to study tidal changes and global ocean currents. How do satellites help study Earth?

21. Sea Beam Sea Beam technology uses Sonar (sound waves) to map the ocean floor from a ship. –A sound wave is sent from a ship to the ocean floor. –A receiver on the ship picks up the echo. –Similar to satellite imaging, a computer calculates the distance based upon the known speed of sound through seawater and the travel time. –Sea Beam technology is used by fishing fleets, deep-sea drilling operations, oceanographers, volcanologists, and archaeologists.

22. Global Positioning System (GPS) GPS is a satellite navigation system that enables users to locate their approximate Earth location. –These satellites can also relay information to a GPS receiver about elevation, direction of movement and speed. –GPS technology is used extensively in plane and ship navigation, and to help people find a destination or determine their current location. GPS IIR

23. The Geographic Information System (GIS) GIS uses a worldwide database to create layers, or “themes” of information that can be placed one on top of another to create a comprehensive map. –GIS map layers remain linked to the original source so that if the original information changes, the GIS layers also change. –Thus, the map will always be up-to-date.

24. Visualizing GPS Satellites GPS receivers detect signals from the 27 GPS satellites orbiting Earth. –Using signals from at least three satellites, the receiver calculates the location within 10 m using a technique called triangulation.

25. A.One B.Two C.Three D.Four At least how many GPS satellites are needed to fix a location? Pop Quiz

26. A.Speed and time of the echo B.Wavelength and time of the echo C.Power and speed of the echo D.Time and power of the echo A radar signal is sent from a satellite to the ocean’s surface. What information is needed to calculate distance from the return echo? Pop Quiz

27. A.The Titan II launch vehicle blew up. B.A fuel line ruptured. C.The solar array wouldn’t deploy. D.Someone in the control room sent the wrong command. Why did Landsat 6 fail to reach orbit? Pop Quiz