Presentation is loading. Please wait.

Presentation is loading. Please wait.

IBM 701 COMPUTER. The 701 installation at General Motors Research Laboratories. (Courtesy George F. Ryckman.) IBM 701 COMPUTER.

Published bySylvia Gardner Modified over 9 years ago

Similar presentations

Presentation on theme: "IBM 701 COMPUTER. The 701 installation at General Motors Research Laboratories. (Courtesy George F. Ryckman.) IBM 701 COMPUTER."— Presentation transcript:

1 IBM 701 COMPUTER

2 The 701 installation at General Motors Research Laboratories. (Courtesy George F. Ryckman.) IBM 701 COMPUTER

3 CPC IBM Card Programmed Calculator $1800/month 150 three-address instructions per minute. IBM 701 $18000/month 100X FASTER

4 IBM 701 COMPUTER first stored-program machine installed in GM. Torsional vibration studies, advanced bearing-load calculations, propeller design and data reduction, harmonic analysis with feedback checking, automatic-advance cams on distributors, pump pressure-wave analysis, Turbine blade properties, fatigue-data analysis, hypoid gear design.

5 IBM 701 COMPUTER 750,000 hourly employment force actuarial and statistical

6 IBM 701 COMPUTER BUT MTBF=3.5h cathode-ray-tube electro static main memory

7 IBM 701 COMPUTER Regional Assembly Language SPEEDCODE ACOM transformed the address fixed-point arithmetic machine into a stream-lined three-address floating-point system.

8 IBM 701 COMPUTER “compilers” macroprocessors READ&PRINT

9 IBM 701 COMPUTER 1955 INPUT/OUTPUT SYSTEM

10 IBM 701 COMPUTER

Download ppt "IBM 701 COMPUTER. The 701 installation at General Motors Research Laboratories. (Courtesy George F. Ryckman.) IBM 701 COMPUTER."

Similar presentations

Instruction Sets: Characteristics and Functions Addressing Modes

Instruction Sets: Characteristics and Functions Addressing Modes
Machine cycle.

Machine cycle.
DAP teaching computer architecture at Berkeley since 1977

DAP teaching computer architecture at Berkeley since 1977
8. Code Generation. Generate executable code for a target machine that is a faithful representation of the semantics of the source code Depends not only.

8. Code Generation. Generate executable code for a target machine that is a faithful representation of the semantics of the source code Depends not only.
系 統 程 式 System Programming

系 統 程 式 System Programming
Programming Languages Marjan Sirjani 2 2. Language Design Issues Design to Run efficiently : early languages Easy to write correctly : new languages.

Programming Languages Marjan Sirjani 2 2. Language Design Issues Design to Run efficiently : early languages Easy to write correctly : new languages.
CS 31003: Compilers ANIRUDDHA GUPTA 11CS10004 G2 CLASS DATE : 24/07/2013.

CS 31003: Compilers ANIRUDDHA GUPTA 11CS10004 G2 CLASS DATE : 24/07/2013.
Starting Out with C++, 3 rd Edition 1 Chapter 1. Introduction to Computers and Programming.

Starting Out with C++, 3 rd Edition 1 Chapter 1. Introduction to Computers and Programming.
1. Copyright  2005 by Oxford University Press, Inc. Computer Architecture Parhami2 Figure 7.1 Steps in transforming an assembly language program to an.

1. Copyright  2005 by Oxford University Press, Inc. Computer Architecture Parhami2 Figure 7.1 Steps in transforming an assembly language program to an.
Computer Architecture Wed: 14:00-14:00, 14/34 Instructor: Jihad El-Sana Office:111, Building:37 Tel: 08-6477871.

Computer Architecture Wed: 14:00-14:00, 14/34 Instructor: Jihad El-Sana Office:111, Building:37 Tel:
Chapter 1: An Overview of Computers and Programming Languages

Chapter 1: An Overview of Computers and Programming Languages
Implementation of a Stored Program Computer

Implementation of a Stored Program Computer
Introduction CNC (Computer Numerical Control) Machines are automated machines, which uses programs to automatically execute a series of machining operations.

Introduction CNC (Computer Numerical Control) Machines are automated machines, which uses programs to automatically execute a series of machining operations.
 The so-called second-generation computers can be taken to be those produced during the second decade of the electronic computer era (approximately 1955-1964)

 The so-called second-generation computers can be taken to be those produced during the second decade of the electronic computer era (approximately )
Michael Monroig Michael Fiorelli.  The Processor is also known as the CPU or Central Processing Unit.  Processors carry out the instructions of computer.

Michael Monroig Michael Fiorelli.  The Processor is also known as the CPU or Central Processing Unit.  Processors carry out the instructions of computer.
SHARANPREET SIDHU IT/9. The first generation of computers is said by some to have started in 1946 with Eniac, the first 'computer' to use electronic.

SHARANPREET SIDHU IT/9. The first generation of computers is said by some to have started in 1946 with Eniac, the first 'computer' to use electronic.
KEY COMPONENTS OF A COMPUTER SYSTEM ANDREW LOLAVAR.

KEY COMPONENTS OF A COMPUTER SYSTEM ANDREW LOLAVAR.
CSE378 Gen. Intro1 Machine Organization and Assembly Language Programming Machine Organization –Hardware-centric view (in this class) –Not at the transistor.

CSE378 Gen. Intro1 Machine Organization and Assembly Language Programming Machine Organization –Hardware-centric view (in this class) –Not at the transistor.
5-Stage Pipelining Fetch Instruction (FI) Fetch Operand (FO) Decode Instruction (DI) Write Operand (WO) Execution Instruction (EI) S3S3 S4S4 S1S1 S2S2.

5-Stage Pipelining Fetch Instruction (FI) Fetch Operand (FO) Decode Instruction (DI) Write Operand (WO) Execution Instruction (EI) S3S3 S4S4 S1S1 S2S2.
Computer are used to control the operation of many and everyday objects. The instructions contained in the computer program send signals out to computer.

Computer are used to control the operation of many and everyday objects. The instructions contained in the computer program send signals out to computer.

Similar presentations

Ads by Google