1. General Characteristics of Negative-Feedback Amplifiers
Sensitivity of transfer Amplification: The fractional change in amplification with feedback divided by the fractional change without feedback is called the sensitivity of the transfer gain.
Mathematically, the sensitivity of the transfer gain can be written as follows:
We know that,
Prepared by Dr. M. A. Mannan

2. Hence, the sensitivity is
For example, if S=0.1 then
That means the percentage change in gain with feedback is one-tenth the percentage variation in amplification if no feedback is present.
Desensitivity of transfer Amplification: The reciprocal of the sensitivity is called the desensitivity D, or
From Eq. (13-4) [Af=A/(1+bA)], it is seen that the transfer gain is divided by the desensitivity after feedback is added.
Thus
and the gain may be made to depend entirely on the feedback network.

3. Frequency Distortion:
It is seen from Eq. (13-9) [Af=1/b] that if the feedback network is purely resistive, the gain with feedback is not depend on frequency even though the basic amplifier gain is frequency dependent.
So the frequency distortion arising because of varying gain, A, with frequency is considerably reduced in a negative feedback amplifier.

4. Nonlinear Distortion:
Suppose that a large amplitude signal is applied to a stage of an amplifier so that the operation of the device extends slightly beyond its range of linear operation, and as a consequence the output signal is slightly distorted.
Negative feedback now introduced, and the input signal is increased by the same amount by which the gain is reduced, so that the output signal amplitude remains the same.
It is clear from Eq. (13.9) that the negative feedback reduces the dependence of the overall closed-loop gain (Af) on the open-loop gain (A) of the amplifier.

5. Let’s understand this through this example:
Say the open loop gain drops from 1000 (A1) to 100 (A2) had we a negative feedback gain with b=0.01 then
That means the closed-loop gain drops from 90.9 to 50.
This means it gets linearized.

6. Reduction of Noise:
Negative feedback can be employed to reduce the noise in an amplifier (i.e. to increase the signal-to-noise ratio, SNR).
The signal-to-noise (SNR) for the amplifier A1 is
We may precede the original amplifier A1 by the clean amplifier A2 and apply negative feedback

7. So the signal-to-noise ratio in the output is obtained as follows:
It is seen from above equation that the signal-to-noise ration is increased by the use of negative feedback.

8. Increase Bandwidth: By employing the negative feedback the bandwidth can be increased.
Let an amplifier have the upper and lower cutoff frequency wH and wL without feedback. The gain of high frequency and low frequency gain Ao (=Amid) as
For high frequency, the overall gain with negative feedback can be obtained as follows:
The upper cutoff frequency with negative feedback is the frequency at which the real and imaginary parts of the denominator of above equation are equal, thus

9. It is seen from the previous equation that the upper cutoff frequency is increased by applying negative feedback.
Similarly, the lower cutoff frequency is obtained as follows:
It is revealed in the above equation that the lower cutoff frequency is decreased by applying negative feedback.
From the above discussion it can be stated that negative feedback increases the bandwidth of an amplifier.

10. Input Resistance
If the feedback signal is returned to the input in series with the applied voltage, it increases the input resistance.
Since the feedback voltage Vf oppose Vs, the input current Ii is less than it would be if Vf were absent.
Hence the input resistance Rif=Vs/Ii is greater than the input resistance without feedback Ri.
For this type of feedback topology Rif=Ri(1+bA)=RiD.
If the feedback is returned to the input in shunt with the applied current, it decreases the input resistance.

11. Since Is=Ii+If, then the current Ii (for a fixed value of Is) is decreased from what it would be if there were no feedback current.
Hence the input resistance Rif=Vi/Is= RiIi/Is is decreased because of this type of feedback.
For this type of feedback topology Rif=Ri/(1+bA)=Ri/D.

12. Output Resistance
Negative feedback which samples the output voltage, regardless of how this output signal is returned to the input, tends to decrease the output resistance (Rof<<Ro).
Negative feedback which samples the output current, regardless of how this output signal is returned to the input, tends to increase the output resistance (Rof>>Ro).
The output resistance for the feedback amplifier can be defined as the resistance with feedback Rof looking into the output terminals with RL disconnected.
The output resistance is determined by applying a voltage V, resulting in a current I, with Vs (Vs =0 where input source is voltage) shorted out or Is (Is =0 where input source is current) opened out. So, Rof=V/I.

13. Input Resistance of Voltage-Series Feedback
Fig shows the topology of Fig. (a) in which the amplifier is replaced by its Thevenin’s model.
From Fig the input impedance with feedback is Rif=Vs/Ii.
Also,

14. From Eqs. (13-11) and (13-12)
Whereas Av represents the open-circuit voltage gain without feedback, Eq. (13-13) indicates that AV is the voltage gain without feedback taking the load RL into account.
Therefore

15. Output Resistance of Voltage-Series Feedback
Replacing the output voltage Vo by V of Fig and setting Vs=0, we obtained
From this equations, we obtained as follows:
Note that Ro is divided by the desensitivity factor 1+bAv, which contains the open-circuit voltage gain Av (not AV).

16. The output resistance with feedback which includes RL as part of the amplifier is given by Rof in parallel with RL, or
where, Ro’=Ro||RL is the output resistance without feedback but with RL considered as part of the amplifier.

17. Input Resistance of Current-Series Feedback
Fig shows the topology of Fig. (b) in which the amplifier is replaced by its Thevenin’s input model and Norton’s output model.
From the above figure the input impedance with feedback is Rif=Vs/Ii.
Also

18. From Eqs. ( ) and ( )
Whereas Gm represents the short-circuit transconductance without feedback, Eq. (13-18) indicates that GM is the transconductance without feedback taking the load RL into account.
Therefore

19. Output Resistance of Current-Series Feedback
Replacing the output voltage Vo and Io by V and -I, respectively, of Fig and setting Vs=0, we obtained
From this equations, we obtained as follows:
Note that Ro is multiplied by the desensitivity factor 1+bGm, which contains the transconductance Gm (not GM).

20. The output resistance with feedback which includes RL as part of the amplifier is given by Rof in parallel with RL, or

21. Input Resistance of Current-Shunt Feedback
The topology of Fig. (c) is indicated in Fig , with the amplifier replaced by its Norton’s model.
From the Fig the input impedance with feedback is Rif=Vi/Is.
Also

22. From Eqs. (13-19) and (13-20)
From Fig 13-11, Rif=Vi/Is and Ri=Vi/Ii. Using (13-22), we obtain
Whereas Ai represents the short-circuit current gain without feedback, Eq. (13-23) indicates that AI is the current gain without feedback taking the load RL into account.
Therefore

23. Output Resistance of Current-Shunt Feedback
Replacing the output voltage Vo and Io by V and -I, respectively, of Fig and setting Is=0, we obtained
From this equations, we obtained as follows:
Note that Ro is multiplied by the desensitivity factor 1+bAi, which contains the short-circuit current gain Ai (not AI).

24. The output resistance with feedback which includes RL as part of the amplifier is given by Rof in parallel with RL, or
For RL=, AI=0 and , so that Eq. (13-37) reduces to

25. Input Resistance of Voltage-Shunt Feedback
Fig shows the topology of Fig. (d) in which the amplifier is replaced by its Norton’s input model and Thevenin’s output model.
From the Fig the input impedance with feedback is Rif=Vi/Is.
Also

26. From ( ) and ( )
From Fig 13-11, Rif=Vi/Is and Ri=Vi/Ii. Using (13-22), we obtain
Whereas Rm represents the open-circuit transresistance without feedback, Eq. (13-26) indicates that RM is the transresistance without feedback taking the load RL into account.
Therefore

27. Output Resistance of Voltage-Shunt Feedback
Replacing the output voltage Vo and Io by V and -I, respectively, of Fig and setting Is=0, we obtained
From this equations, we obtained as follows:
Note that Ro is divided by the desensitivity factor 1+bRm, which contains the transresistance Rm (not RM).

28. The output resistance with feedback which includes RL as part of the amplifier is given by Rof in parallel with RL, or
where, is the output resistance without feedback but with RL considered as part of the amplifier.
Note that is now divided by the desensitivity factor D=1+bRM which contains the voltage gain RM that takes RL into account.

29. Table 13-4 summarizes the different components for different topologies.