1. THEMIS Instrument CDR 1 UCB, April 19-20, 2004 Boom Electronics Board (BEB) Engineering Peer Review Apr. 20, 2004 Hilary Richard

2. THEMIS Instrument CDR 2 UCB, April 19-20, 2004 BEB Requirements Functional Requirements Spin Plane Booms, for each provide: –Floating Ground Driver –“Bias”, “Guard”, “Usher” programmable potentials –“Braid” programmable, switchable potential –AC test signal source Axial Booms, for each provide: –Floating Ground Driver –“Bias”, “Guard”, “Usher” programmable potentials –AC test signal source

3. THEMIS Instrument CDR 3 UCB, April 19-20, 2004 BEB Requirements, con’t.

4. THEMIS Instrument CDR 4 UCB, April 19-20, 2004 BEB Analog Electronics

5. THEMIS Instrument CDR 5 UCB, April 19-20, 2004 BEB Block Diagram

6. THEMIS Instrument CDR 6 UCB, April 19-20, 2004 Braid Bias

7. THEMIS Instrument CDR 7 UCB, April 19-20, 2004 Preliminary PCB Layout

8. THEMIS Instrument CDR 8 UCB, April 19-20, 2004 BEB ETU

9. THEMIS Instrument CDR 9 UCB, April 19-20, 2004 BEB ETU

10. THEMIS Instrument CDR 10 UCB, April 19-20, 2004 BEB Parts Analysis Parts Stress Analysis Design meets derating guidelines of GSFC PPL-21 Worst Case Temperature Analysis Parts meet Temperature Guidelines –Operating Temperature range: –30C to 45C –Survival Temperature range: –50C to 65C Only one “high” power device (Actel 54SX72) –Operating power dissipation: 63 mW

11. THEMIS Instrument CDR 11 UCB, April 19-20, 2004 BEB ETU Mass and Power Power Estimated worst case power at PDR: 1667mW –Includes Preamp power of 324mW Measured ETU operating power: 790mW –Including Preamp, total = 1114mW Mass Estimated mass at PDR: 504g Measured ETU mass: 426g

12. THEMIS Instrument CDR 12 UCB, April 19-20, 2004 BEB ETU Test Results DC Response of Floating Ground Driver, FL_GND2

13. THEMIS Instrument CDR 13 UCB, April 19-20, 2004 BEB ETU Test Results, con’t. AC Response of Floating Ground Driver, FL_GND2

14. THEMIS Instrument CDR 14 UCB, April 19-20, 2004 BEB ETU Test Results, con’t. DC Response of Bias Driver, BIAS1

15. THEMIS Instrument CDR 15 UCB, April 19-20, 2004 BEB ETU Test Results, con’t. AC Response of Bias Driver, BIAS1

16. THEMIS Instrument CDR 16 UCB, April 19-20, 2004 BEB ETU Test Results, con’t. Preliminary Crosstalk Data Set-up: –Signal Injected into Ref. Voltage of BIAS3 –VSphere3 = 10V PP, 150Hz –Output of neighboring BIAS Driver examined Crosstalk observed on BIAS2: –VSphere2 not terminated –Signal Amplitude is -75.8dB (relative to 7.07V RMS ) –VSphere2 grounded –Crosstalk undetectable (< -103dB)

17. THEMIS Instrument CDR 17 UCB, April 19-20, 2004 BEB / EFI Subsystem Test Integrated Testing Includes: –BEB, Boom wire, Preamp –Sensor Boxes with Plasma Simulator (R║C) –GSE Automated Data Acquisition Test Results –DC Tests –Isolation, Sensor biasing, Usher/Guard Biasing, Braid biasing –DC Gain/Offset –AC Tests –AC input impedance, Transfer function, Crosstalk, Noise level –Linearity, Slew rate

18. THEMIS Instrument CDR 18 UCB, April 19-20, 2004 EFI Test/Characterization

19. THEMIS Instrument CDR 19 UCB, April 19-20, 2004 BEB GSE Data Acquisition

20. THEMIS Instrument CDR 20 UCB, April 19-20, 2004 BEB GSE Data Acquisition Capabilities: Supports Automated test of Flight Hardware “VME-style” backplane –Accepts BEB and DFB –DCB-simulator implements CDI command 16-Channel 16-bit ADC (±100V range) –6 Vsphere, 2 Braid, 2 Usher, 2 Guard, 2 Flt. Gnd Programmable Signal Source w/ –±60Vdc offset range –30mV to 15Vpp AC (DC-16kHz) –1mV to 500mVpp AC (100k – 500kHz) LVPS and PCB simulation –Power services programmable on/off –+5VD, +2.5VD, ±10VA, ±100VA –Current monitors

21. THEMIS Instrument CDR 21 UCB, April 19-20, 2004 BEB GSE Software Capabilities: Scripted or interactive entry of CDI, GPIB, and DAQ commands Continuous analog acquisition mode with real-time stripchart displays “One-shot” acquisition mode for detailed examination, processing, and archival of analog input data MATLAB interface –TCP/IP interface allows GSE to be controlled via remote host –Full access to CDI, GPIB, analog and digital I/O commands –Interface libraries allow GSE functions to be accessed just like native MATLAB commands Device control –GPIB programmable function generator serves as signal source –DAQPad 16-input, 16-bit, 333 kSamp/sec for analog data acquisition –DAQPad analog and digital outputs serve as controls for signal source amplifier, LVPS switching, and current monitor MUX –TCP/IP interface to 6U VME GSE Interface Board for sending CDI commands

22. THEMIS Instrument CDR 22 UCB, April 19-20, 2004 BEB GSE Software, con’t.

23. THEMIS Instrument CDR 23 UCB, April 19-20, 2004 BEB Design Status Completed ETU Design and Fabrication Characterization w.r.t. DC gain and AC response –In progress Available for testing with Preamp prototypes EFI Sensor Test Program GSE Data Acquisition system completed Integrated tests with preamps and boom units Issues Actel 54SX72 failures, total of 4 out of 7 –2 failed programming –2 failed “in circuit”, cause unknown

24. THEMIS Instrument CDR 24 UCB, April 19-20, 2004 BEB Add’l Info Additional slides included: Floating ground driver schematic Bias driver schematic

25. THEMIS Instrument CDR 25 UCB, April 19-20, 2004 Floating Ground Driver Heritage Design CLUSTER, POLAR, FAST Minor changes in part selection

26. THEMIS Instrument CDR 26 UCB, April 19-20, 2004 Bias Driver Heritage Design CLUSTER, POLAR, FAST Minor changes in parts selection and DAC