1. Electronic Instrumentation Experiment 4 * Part A: Bridge Circuits * Part B: Potentiometers and Strain Gauges * Part C: Oscillation of an Instrumented Beam * Part D: Oscillating Circuits

2. Part A w Bridges w Thevenin Equivalent Circuits

3. Wheatstone Bridge A bridge is just two voltage dividers in parallel. The output is the difference between the two dividers.

4. A Balanced Bridge Circuit

5. Thevenin Voltage Equivalents w In order to better understand how bridges work, it is useful to understand how to create Thevenin Equivalents of circuits. w Thevenin invented a model called a Thevenin Source for representing a complex circuit using A single “pseudo” source, Vth A single “pseudo” resistance, Rth   

6. Thevenin Voltage Equivalents This model can be used interchangeably with the original (more complex) circuit when doing analysis. The Thevenin source, “looks” to the load on the circuit like the actual complex combination of resistances and sources.

7. The Function Generator Model w Recall that the function generator has an internal impedance of 50 Ohms. w Could the internal circuitry of the function generator contain only a single source and one resistor? w This is actually the Thevenin equivalent model for the circuit inside the function generator

8. Thevenin Model Load Resistor

9. Note: w We might also see a circuit with no load resistor, like this voltage divider.

10. Thevenin Method w Find Vth (open circuit voltage) Remove load if there is one so that load is open Find voltage across the open load w Find Rth (Thevenin resistance) Set voltage sources to zero (current sources to open) – in effect, shut off the sources Find equivalent resistance from A to B A B

11. Example: The Bridge Circuit w We can remodel a bridge as a Thevenin Voltage source    

12. Find Vth by removing the Load AABB Let Vo=12, R1=2k, R2=4k, R3=3k, R4=1k

13. To find Rth w First, short out the voltage source (turn it off) & redraw the circuit for clarity. AB A B

14. Find Rth w Find the parallel combinations of R1 & R2 and R3 & R4. w Then find the series combination of the results.

15. Redraw Circuit as a Thevenin Source w Then add any load and treat it as a voltage divider.

16. Thevenin Method Tricks w Note When a short goes across a resistor, that resistor is replaced by a short. When a resistor connects to nothing, there will be no current through it and, thus, no voltage across it.

17. Thevenin Applet (see webpage) w Test your Thevenin skills using this applet from the links for Exp 3

18. Does this really work? w To confirm that the Thevenin method works, add a load and check the voltage across and current through the load to see that the answers agree whether the original circuit is used or its Thevenin equivalent. w If you know the Thevenin equivalent, the circuit analysis becomes much simpler.

19. Thevenin Method Example w Checking the answer with PSpice w Note the identical voltages across the load. 7.4 - 3.3 = 4.1 (only two significant digits in Rth)

20. Part B w Potentiometers w Strain Gauges w The Cantilever Beam w Damped Sinusoids

21. Potentiometers “Pots”

22. More on Pots

23. DC Sweeps are Linear

24. Other types of linear sweeps You can use a DC sweep to change the value of other parameters in PSpice. In this experiment you will sweep the set parameter of a pot from 0 to 1.

25. Strain Gauges

26. Strain Gauge in a Bridge Circuit

27. Pot in a Bridge Circuit You can use a pot for two of the resistors in a bridge circuit. Use the pot to balance the bridge when the strain gauge is at rest.

28. Cantilever Beam The beam has two sensors, a strain gauge and a coil. In this experiment, we will hook the strain gauge to a bridge and observe the oscillations of the beam.

29. Modeling Damped Oscillations w v(t) = A sin(ωt)

30. Modeling Damped Oscillations w v(t) = Be -αt

31. Modeling Damped Oscillations w v(t) = A sin(ωt) Be -αt = Ce -αt sin(ωt)

32. Finding the Damping Constant w Choose two maxima at extreme ends of the decay.

33. Finding the Damping Constant w Assume (t0,v0) is the starting point for the decay. w The amplitude at this point,v0, is C. w v(t) = Ce -αt sin(ωt) at (t1,v1): v1 = v0e -α(t1-t0) sin(π/2) = v0e -α(t1-t0) w Substitute and solve for α: v1 = v0e -α(t1-t0)

34. Part C w Harmonic Oscillators w Analysis of Cantilever Beam Frequency Measurements

35. Examples of Harmonic Oscillators w Spring-mass combination w Violin string w Wind instrument w Clock pendulum w Playground swing w LC or RLC circuits w Others?

36. Harmonic Oscillator w Equation w Solution x = Asin(ωt) w x is the displacement of the oscillator while A is the amplitude of the displacement

37. Spring w Spring Force F = ma = -kx w Oscillation Frequency w This expression for frequency hold for a massless spring with a mass at the end, as shown in the diagram.

38. Spring Model for the Cantilever Beam w Where l is the length, t is the thickness, w is the width, and m beam is the mass of the beam. Where m weight is the applied mass and a is the length to the location of the applied mass.

39. Finding Young’s Modulus w For a beam loaded with a mass at the end, a is equal to l. For this case: where E is Young’s Modulus of the beam. w See experiment handout for details on the derivation of the above equation. w If we can determine the spring constant, k, and we know the dimensions of our beam, we can calculate E and find out what the beam is made of.

40. Finding k using the frequency w Now we can apply the expression for the ideal spring mass frequency to the beam. w The frequency, f n, will change depending upon how much mass, m n, you add to the end of the beam.

41. Our Experiment w For our beam, we must deal with the beam mass, the extra mass of the magnet and its holder (for the magnetic pick up coil), and any extra load we add to the beam to observe how its performance depends on load conditions. w Since real beams have finite mass concentrated at the center of mass of the beam, it is necessary to use the equivalent mass at the end that would produce the same frequency response. This is given by m = 0.23m beam. w The beam also has a sensor at the end with some finite mass, we call this mass, m 0 m 0 = m doughnut + m magnet = 13g + 24g = 37g

42. Our Experiment To obtain a good measure of k and m, we will make 4 measurements of oscillation, one with only the sensor and three others by placing an additional mass at the end of the beam.

43. Our Experiment w Once we obtain values for k and m we can plot the following function to see how we did. w In order to plot m n vs. f n, we need to obtain a guess for m, m guess, and k, k guess. Then we can use the guesses as constants, choose values for m n (our domain) and plot f n (our range).

44. Our Experiment The output plot should look something like this. The blue line is the plot of the function and the points are the results of your four trials.

45. Our Experiment w How to find final values for k and m. Solve for k guess and m guess using only two of your data points and two equations. (The larger loads work best.) Plot f as a function of load mass to get a plot similar to the one on the previous slide. Change values of k and m until your function and data match.

46. Our Experiment w Can you think of other ways to more systematically determine k guess and m guess ? w Experimental hint: make sure you keep the center of any mass you add as near to the end of the beam as possible. It can be to the side, but not in front or behind the end. Magnet C-Clamp

47. Part D w Oscillating Circuits w Comparative Oscillation Analysis w Interesting Oscillator Applications

48. Oscillating Circuits w Energy Stored in a Capacitor CE =½CV² w Energy stored in an Inductor LE =½LI² w An Oscillating Circuit transfers energy between the capacitor and the inductor. http://www.walter-fendt.de/ph11e/osccirc.htm

49. Voltage and Current w Note that the circuit is in series, so the current through the capacitor and the inductor are the same. w Also, there are only two elements in the circuit, so, by Kirchoff’s Voltage Law, the voltage across the capacitor and the inductor must be the same.

50. Oscillator Analysis w Spring-Mass w W = KE + PE w KE = kinetic energy=½mv² w PE = potential energy(spring)=½kx² w W = ½mv² + ½kx² w Electronics w W = LE + CE w LE = inductor energy=½LI² w CE = capacitor energy=½CV² w W = ½LI² + ½CV²

51. Oscillator Analysis w Take the time derivative

52. Oscillator Analysis w W is a constant. Therefore, w Also w W is a constant. Therefore, w Also

53. Oscillator Analysis w Simplify

54. Oscillator Analysis w Solution x = Asin(ωt) V= Asin(ωt)

55. Using Conservation Laws w Please also see the write up for experiment 3 for how to use energy conservation to derive the equations of motion for the beam and voltage and current relationships for inductors and capacitors. w Almost everything useful we know can be derived from some kind of conservation law.

56. Large Scale Oscillators Tall buildings are like cantilever beams, they all have a natural resonating frequency. Petronas Tower (452m) CN Tower (553m)

57. Deadly Oscillations The Tacoma Narrows Bridge went into oscillation when exposed to high winds. The movie shows what happened. http://www.slcc.edu/schools/hum_sci/ physics/tutor/2210/mechanical_oscilla tions/ In the 1985 Mexico City earthquake, buildings between 5 and 15 stories tall collapsed because they resonated at the same frequency as the quake. Taller and shorter buildings survived.

58. Atomic Force Microscopy -AFM w This is one of the key instruments driving the nanotechnology revolution w Dynamic mode uses frequency to extract force information Note Strain Gage

59. AFM on Mars w Redundancy is built into the AFM so that the tips can be replaced remotely.

60. AFM on Mars w Soil is scooped up by robot arm and placed on sample. Sample wheel rotates to scan head. Scan is made and image is stored.

61. AFM Image of Human Chromosomes w There are other ways to measure deflection.

62. AFM Optical Pickup w On the left is the generic picture of the beam. On the right is the optical sensor.

63. MEMS Accelerometer w An array of cantilever beams can be constructed at very small scale to act as accelerometers. Note Scale

67. Hard Drive Cantilever w The read-write head is at the end of a cantilever. This control problem is a remarkable feat of engineering.

68. More on Hard Drives w A great example of Mechatronics.