Presentation is loading. Please wait.

Presentation is loading. Please wait.

Powerline Communications: Channel Characterization and Modem Design

Similar presentations


Presentation on theme: "Powerline Communications: Channel Characterization and Modem Design"— Presentation transcript:

1 Powerline Communications: Channel Characterization and Modem Design
Yangpo Gao Helsinki University of Technology

2 Thesis Contents Table of Contents
Introduction PLC Technology Background Channel Measurement and Modeling Disturbance over PLC DMT Based PLC Modem Design Conclusion Reference This thesis is part of project “ PLC controlled LEDs for general lighting system”, which is sponsored by TEKES

3 Introduction

4 History of PLC and Motivation of Thesis
What is PLC PLC – Powerline Communications Using powerline as transmission medium for data communication History of PLC From high voltage (HV) low voltage (LV) Low data rate high data rate Control application multimedia data applications Motivation Cheap “the last mile” solution However, worse channel than other wired network Channel characterization reliable communications

5 PLC Technology Background

6 PLC Technologies Three network levels Efficient coupling
High voltage (110–380 kV) Medium voltage (10–30 kV) Low voltage (230/400 V, in the USA 110 V) (my thesis range) Efficient coupling Inductive coupling Conductive coupling Modulation and error correction OFDM, DMT CDMA FEC

7 EMC Issues EMC --Electromagnetic compatibility
The ability of a device or system to function satisfactorily in its electromagnetic environment without introducing intolerable electromagnetic disturbances in the form of interferences to any other system in that environment, even to itself.

8 Standardizations PLC standardization bodies International National
Regional National

9 Channel Measurement and Modeling

10 Transmission Line Theory
A piece of mains cable can be modeled as following figure Attenuation constant phase Characteristic impedance Propagation constant R : resistance . L : inductance. G : conductance C : capacitance

11 Channel Measurement Setup
Equipment: Network Analyzer (NA) Coupling Circuit Coupling circuit Conductive coupling High pass filter Galvanic isolation Over Voltage protection

12 PLC Cable Measurements
Rapid fluctuation caused by impedance mismatch Maximum of 4 dB attenuation 100 MHz Cable transversal Cable Type Size (mm2) Vulcanize rubber cable (three-wire) 0.75 1 PVC/PVC cable (three-wire) PVC/PVC cable (two-wire) 0.5

13 PLC Channel Measurements
Scenario 1: Internet access and distribution Scenario 2: Home networking Scenario 1: Network topology is known, or easy to estimate. Channel is simple, and has few multipath components Scenario 2: Network topology is unknown or it is hard to define. Channel acts as black box. A lot of multipath components

14 Channel Responses Frequency Domain Time Scenario 1 Scenario 2

15 PLC Channel Modeling According to PLC channel multipath phenomenon, channel can be modeled as:

16 Disturbance over PLC

17 PLC Noise Noise Classification: Our concentration
Colored background noise Narrowband noise Periodic impulsive noise, asynchronous to the main frequency Periodic impulsive noise, noise, synchronous to the main frequency Asynchronous impulsive noise Our concentration

18 Noise Measurement setup
Equipment: Oscilloscope Spectrum Analyzer Coupler

19 Colored Background Noise
Quasi-Static behavior Statistic information is extracted in table Can be modeled as: s b c Max -94 -80 -0.4 Min -124 -100 -0.6 Average -105 -90 -0.5

20 Random Impulsive Noise
Caused by frequency bursts generated by electrical devices connected to the powerline. Statistic information is extracted

21 Other Disturbance NEXT Formation FEXT Formation
NEXT (Near End crosstalk) FEXT (Far End crosstalk). NEXT Formation FEXT Formation

22 DMT Based PLC Modem Design

23 DMT Technology Discrete Multi-tone Modulation (DMT) Advantages:
Multicarrier technology – combat frequency selective fading Dynamic bit loading based on SNR – efficient spectrum utilization High channel capacity

24 DMT Based PLC Modem Design
Simulation environment: MATLAB SimuLink MATLAB DSP Blockset Simulated channel response Expected result Bit Error Rate (BER)

25 Simulation and Performance
Optimized bit loading algorithm Modem performance PLC vs AWGN Signal spectrum after PLC channel Signal spectrum before PLC channel

26 Publications Related to My Thesis

27 Publications More information can be found in my publications:
“Channel modeling and modem design for broadband power line communications”, Proceeding of ISPLC 2004, April, Spain “Broadband characterization of indoor powerline channel”, Proceeding of ISPLC 2004, April, Spain “Broadband Characterization of Indoor Powerline Channel and Its Capacity Consideration”, Proceeding of ICC 2005, May, Korea

28 Any Questions? Thank You!


Download ppt "Powerline Communications: Channel Characterization and Modem Design"

Similar presentations


Ads by Google