1. Fall Protection

2. Training Matrix Subject
Description of Subject Matter /Key Items Covered
Who is Required to attend
Frequency
Presented by
Safety Website Section
Fall Protection
Covers training for each employee who might be exposed to fall hazards
All personnel required to use platforms, scissor lift, man-ups or other equipment must utilize fall protection
Initial training
Inadequacies in an affected employee's knowledge or use of fall protection systems
Changes in the workplace render previous training obsolete
Changes in the types of fall protection systems or equipment to be used render previous training obsolete
Facility Manager Maintenance Manager Competent Person
Personal Safety

3. Fall Protection
A system that protects workers who could lose their balance at any given height from falling, usually resulting in injuries.
Fall protection involves the elimination of fall hazards, the prevention of falls, and the control of falls
SAFE
WORK
AREA 6’

4. Fall Protection
Having a fall protection system does not necessarily mean that it’s time to buy harnesses and lanyards.
A Fall Protection Job Safety Analysis is necessary to determine the type of protection needed.
Using one system for every type of work is not the answer
When the need for fall protection has been established; there are two distinct solutions;
Passive
Active

5. Passive Fall Protection System
Passive Fall Protection is a system that is stationary, does not move, adapt, or change when in or out of use.
Passive systems do not require the use of personal protective equipment or active participation from the worker

6. Active Fall Protection
Active fall protection systems require worker participation and share the common feature of securing a harnessed worker to an anchorage point with a lanyard
Active fall protection can be found in the three methods for fall protection systems,
Fall Restraint, Positioning Device and Fall Arrest

7. Fall Protection in General Industry
Guard every floor hole into which a worker can accidentally walk by use of a railing and toeboard or a floor hole cover.
Provide a guardrail and toeboard around every open-sided platform, floor or runway that is 4 feet or higher off the ground or next level.
Regardless of height, if a worker can fall into or onto dangerous machines or equipment (such as a vat of acid or a conveyor belt), employers must provide guardrails and toeboards to prevent workers from falling and getting injured.
Other means of fall protection that may be required on certain jobs include safety harness and line, safety nets, stair railings and handrails
To prevent employees from being injured from falls, employers must:

8. Fall Protection Systems
Fall Restraint, Positioning Device and Fall Arrest systems are different methods of fall protection designed to control fall hazards
They all either prevent a fall from occurring or stop a fall before hitting the ground.
Whatever fall protection system is used, it must effectively protect the workers from fall hazards and consequent injuries.
Fall Restraint
Positioning Device
Fall Arrest
Full Body Harness
Guardrails/hole covers
Warning line
Warning line and Safety monitor
Safety net
Catch platform
Vertical Walls

9. Types of fall restraint/prevention systems include:
Fall Restraint System
A fall restraint system keeps a worker from reaching a fall point preventing a fall from occurring (for example, be able to work only up to the edge of a roof).
Types of fall restraint/prevention systems include:
Standard guardrail system: capable of withstanding at least 200 pounds of force applied within 2 inches of the top edge, in any direction and at any point along the edge
Safety belt or harness (personal fall restraint system) The restraint system can allow the worker to reach only as far as the sides and edges of the walking/working surface.
Warning line system and safety monitor system

10. Fall Restraint- Warning Line Systems
Leading edge work
Warning line
The lines mark off an area within which workers can do leading edge work without fall protection.
Workers must not enter the area outside the boundaries of the warning lines (the control zone) unless protected by additional fall protection systems
SAFE
WORK
AREA 6’
Control Zone
Unprotected sides/edges, leading edge

11. Positioning Device
Positioning device system means a full body harness rigged to allow an employee to be supported on an elevated, vertical surface and work with both hands free while leaning
Positioning devices shall be rigged such that an employee cannot free fall more than 2 feet
Positioning devices shall be secured to an anchorage capable of supporting at least twice the potential impact load of an employee's fall or 3,000 pounds

12. The use of a body belt for fall arrest is prohibited
Fall Arrest Systems
A fall arrest system does not prevent a fall from occurring, but is designed to catch a person who has already fallen.
A Personal Fall Arrest System has three (3) key components
Full Body Harness
Shock Absorbing Lanyard
Anchorage Connector
Deceleration Devices, Self-Retracting Lifelines are often used as part of a PFAS
The use of a body belt for fall arrest is prohibited

13. When stopping a fall, a personal fall arrest system must:
Fall Arrest Systems
When stopping a fall, a personal fall arrest system must:
Limit maximum fall arresting force on an employee to 1,800 pounds when used with a full-body harness;
Limit free fall distance to less than 6 feet (1.8m), and be rigged in such a way as to prevent contact with a lower level;
Bring the employee to a complete stop while limiting maximum deceleration distance to 3-1/2 feet (1.1m); and
Have sufficient strength to withstand twice the potential energy of a worker free falling from a distance of 6 feet (1.8m) (or the free fall distance permitted by the system, whichever is less).

14. Harness Fit
Correct Harness Fit
                                                      
Chest and Leg Straps Offer a Snug Fit
Incorrect Harness Fit
                                                      
Chest strap positioned incorrectly. Should be located at mid-chest to keep shoulder straps snug. Leg straps are too loose.

15. Center of wearer’s back; anchorage above head
Attachment Point
Center of wearer’s back; anchorage above head
The attachment point of the body belt shall be located in the center of the wearer's back. The attachment point of the body harness shall be located in the center of the wearer's back near shoulder level, or above the wearer's head.

16. Shock Absorbing Lanyard
Lanyards are required to have self-closing, self-locking snap hooks to reduce the possibility of disengagement, or “rollout”.
Shock-absorbing lanyards extend deceleration distance during a fall, significantly reducing fall arresting forces
The shock-absorbing lanyard or self-retracting lifeline and the Full-body harnesses are the components that actually bear the greatest fall forces during a fall
Shock Absorbing Lanyard connects to the back D-ring of harnesses and a qualified anchorage connector.

17. Deceleration Distance
"Deceleration distance" is the additional vertical distance a falling employee travels, excluding lifeline elongation and free fall distance, before stopping, from the point at which the deceleration device begins to operate.
It is measured as the distance between the location of an employee's body harness attachment point at the moment of activation (at the onset of fall arrest forces) of the deceleration device during a fall, and the location of that attachment point after the employee comes to a full stop.

18. Free fall Distance
"Free fall distance" is the vertical displacement of the uncontrolled length of travel before the fall arrest equipment activates to apply force to arrest the fall preventing a worker to hit the ground.
Fall distance is measured from the foot level before the fall, to the foot level after the fall
This distance excludes deceleration distance, and lifeline/lanyard elongation, but includes any deceleration device slide distance or self-retracting lifeline/lanyard extension before they operate and fall arrest forces occur.

19. Calculating Fall Clearance
Always know your fall distance and select proper equipment to meet the fall clearance.
It is very important to position your anchorage point directly overhead whenever possible to minimize swing falls.
Illustration: 6 ft. (1.8m) Shock-Absorbing Lanyard with D-Bolt Anchorage Connector

20. Shock-Absorbing Lanyards - Before and After Deployment
Limits the fall energy imposed on an employee during fall arrest.

21. Anchorage/Anchorage Connector
Anchorages must be capable of supporting 5,000 pounds of force per worker.
The anchorage should be easily accessible
Careful consideration should be given when selecting a proper anchorage. Should a fall occur, the worker will be suspended from the anchorage, their life depending on its strength.
Anchorage: Commonly referred to as a tie-off point

22. Self-Retracting Lifelines (SRL)
FALL LIMITERS Lightweight, web retractables that require less fall clearance, offer greater mobility and prevent tripping hazards
SELF-RETRACTING LIFELINES Durable and dependable heavy-duty retractables available with webbing or cable Self-retracting lifelines (fall limiter, personal fall limiter, yo-yo, seatbelt, etc.) are viable alternative connecting devices to shock-absorbing lanyards.

23. Fall arrest systems should match the work situation
Used when engineering controls are not feasible or sufficient to eliminate the risk of a fall
Fall arrest systems should match the work situation

24. Hierarchy of Controls STEP 1
Try to bring the job to the ground level so that there is not a risk of falling.
If you can’t…

25. Hierarchy of Controls STEP 2
Put up a solid barrier or handrail so that there is not a risk of falling.
If you can’t…

26. Hierarchy of Controls STEP 3
Use a platform to work such as a scaffold or an elevating work platform (EWP).
If you can’t…

27. Hierarchy of Controls STEP 4
Use of a fall RESTRAINT system that will stop people reaching the edge.
If you can’t…

28. Hierarchy of Controls STEP 5
Use of a fall ARREST (with energy absorber) that will arrest people if they fall.
If you can’t…. Don’t do the Job! Re-assess the job.

29. Additional Requirements
Personal Fall Arrest Systems are used only where falls can occur
If system is subjected to impact loading, it must be examined by Competent Person
Body belts, harnesses, and components shall be used only for employee protection and not to hoist materials.
Personal fall arrest systems and components subjected to impact loading shall be immediately removed from service and not used again until inspected and determined by a competent person to be undamaged and suitable for reuse.
The employer shall provide for prompt rescue of employees in the event of a fall or shall assure that employees are able to rescue themselves.
Failure is not an option when in doubt throw it out

30. Additional Requirements
Inspected prior to each use
Personal fall arrest systems shall be inspected prior to each use for wear, damage and other deterioration, and defective components shall be removed from service.
Personal fall arrest systems shall not be attached to guardrail systems, nor shall they be attached to hoists except as specified in other subparts of this Part.
When a personal fall arrest system is used at hoist areas, it shall be rigged to allow the movement of the employee only as far as the edge of the walking/working surface.

31. Additional Requirements
Recognize potential fall hazards
Evaluate the risk posed by each hazard
Control the hazard with preventive or protective measures
Determine which system to use in specific work environments
Demonstrate proper anchoring procedures
Conduct inspection and maintenance procedures
Properly wear fall protection equipment including size, fit and adjustment
To maintain a safe work environment, it is essential that persons are properly trained to:

32. QUESTIONS?