1. Seamanship: General Ropework
By the end of this session cadets will be able to:
–Describe the elementary safety rules when carrying out
general ropework
–Explain the reasons for coiling a rope
–Demonstrate the coiling of a rope
–Explain the reasons for cheesing a rope
–Demonstrate the cheesing of a rope
–Explain the reasons for faking a rope
–Demonstrate the faking of a rope

2. Know the safe working load of the rope, and don’t exceed the limit
Think Safety!
Do not control any rope, under a heavy load, with bare hands
Always use a cleat/bollard or post when controlling ropes under heavy load
Remove rings and watches or you risk losing a figure (known as “de-gloving”)

7. If loads are being raised or working overhead, then?
You should use a hard hat!
When working overhead ensure your tools are connected to you, your ladder, fixing so that they can not be dropped
Put signs out to let people know where you re working, better still fence off the area off so people cant walk under you

8. The warning cry to those below is “Stand from Under” or “Under Below”
Always keep a good look out and remain alert what is above you
Never stand below an item that is being lowered or hoisted
The warning cry to those below is “Stand from Under” or “Under Below”

9. A seamanship knife if a practical and valuable tool
Worn on a lanyard around the neck, stored in the back pocket of trousers.
The end of the blade should be rounded and not pointed
The blade should always be sharp – you never know when you will need it
Used as a tool and not a weapon

10. Used as a tool and not a weapon
Serrated blade has a quicker cut (plain blade is cleaner
Shackle key
Screwdriver blade
Loop for lanyard
Marlin spike to help ease knots

11. A knife is best passed to someone else with the blade folded away
When passing a knife with the blade out, pass the handle first with the cutting edge away from you
Used as a tool and not a weapon

12. Abrasion will weaken a rope
Abrasion will weaken a rope. Wrap and tie chafing gear around the rope where rubbing occurs
Avoid sudden strains or jerks, which can snap a rope
Always look out for chafing and take action to stop or minimise it
Consider if the rope is useable

13. Why coil a rope?
So its immediately ready for further use

14. How to coil a rope?
Coil the rope on the floor in a clockwise direction (to the right)
Each coil should be placed on the previous coil
Ideally, they should be stored out of the water and dirt (dirt will act as sandpaper and slowly wear the rope)
A rope will accept a few twists before becoming snarled especially if they are with the lay

15. Ordinary hand lay The direction of the lay of the outer layer of wires in the strands is opposite to the direction of lay of the strands in the rope. Ordinary lay is more resistant to kinking and untwisting, and less likely to fail as a result of crushing and distortion.

16. Right hand lay (Z) The strands are twisted to the right around the core. Right hand lay is the most common lay direction in a rope. Left hand lay (S) The strands are twisted to the left around the core.
Which am I?
Right hand lay (Z) Left hand lay (S)

17. Cheesing a rope
Used when the rope will need to be rendered (used) quickly through a block
Provide a very neat stow
You would only do this with a short rope

18. Cheesing a rope
Start the coils on the deck/ground – remember always coil to the right
Now that the coils are in place, put the palm of your hand on the centre of the rope and start to make right handed turns
The cheeses is complete when the coil is wound tight and the working end is all used
Sometimes this is referred to as “Flemishing”

19. Faking a rope
Used when a rope will have to be paid out (let out) quickly
The fake should be as long as the space allows
A faked rope acquires less turns than a coiled rope and has less chance of becoming snarled
Care should be taken that each bight at the end of a fake is laid under that immediately preceding it to ensure that it can run clear

20. Faking a rope
The rope should be laid on the deck in a motion of moving from left to right (clockwise looks)
The loops should be places on the previous loop to allow the rope to run freely
Use as much space as you have

21. Name
Rank
Date
Question
Answer
What is a seaman’s knife used for? 1. 2.
Why should you not have bare hands when working with ropes?
What should you not wear when working with ropes?
Why should you not stand in a coil?
When would you fake a rope?
Draw an image of a cheesed rope
Question
Answer
Explain why you would coil a rope?
Draw a right-lay rope?
Is it a “Z” or an “S”?
What is a marlin spike?
What is the most basic thing you should do when around ropes?
Why do you coil a rope?
Draw an image of a faked rope?

22. Name
Rank
Date
Question
Answer
What is a seaman’s knife used for?
1. Cutting things
2. Marlin Spike helps loosed knots
Why should you not have bare hands when working with ropes?
Possible to get rope burns
What should you not wear when working with ropes?
Rings and watches as they could get caught
Why should you not stand in a coil?
Possible to get broken ankles
When would you fake a rope?
When it needs to be played out quickly
Draw an image of a cheesed rope
Question
Answer
Explain why you would coil a rope?
To avoid it knotting, ensure it is ready for next use
Draw a right-lay rope?
Is it a “Z” or an “S”?
What is a marlin spike?
Shaped in the form of a cone tapered to a rounded or flattened point, they aid in such tasks as unlaying rope for splicing, untying knots
What is the most basic thing you should do when around ropes?
Keep a lookout!
Why do you coil a rope?
Draw an image of a faked rope?