The Compound Microscope Proper use and care of microscope

Parts of the Microscope

A B F E H J G I C K D L M A. Eyepiece B. Body Tube C. Coarse Adjustment F D. Fine Adjustment E H E. Arm Medium (10x) F. Revolving Nosepiece J G G. High Power Objective I H. Low Power Objective C I. Stage Clips K D J. Stage L K. Diaphragm M L. Light Source (Lamp) M. Base

A Compound Microscope A compound light microscope uses two lenses to make an image look bigger. One is the eyepiece lens and the other is the objective lens. Each lens bends the light making the image look larger. What is the magnification number on the eyepiece? 10x What is the magnification number written on each objective lens? low power: 4x medium power: 10x high power: 40x

Calculating Total Magnification To figure out the total magnification use this equation: Total Magnification (x) = Eyepiece x Objective Use the equation above to calculate total magnification. Total Magnification under Low power= 10 x 4 = 40x Total Magnification under Medium Power = 10 x 10 = 100x Total Magnification under High Power = 10 x 40 = 400x

Magnification Your microscope has 3 magnifications: Low, Medium and High. Each objective will have written the magnification. In addition to this, the ocular lens (eyepiece) has a magnification. The total magnification is the ocular x (times) objective Magnification Ocular Lens Total Magnification Low power/ scanning 4x 10x 40x Medium power 100x High power 400x

Objectives rotate in nosepiece Ocular remains the same (10X) Changing objectives changes total magnification

General Procedures 1. Make sure all books, etc., are out of the aisles and off desks. 2. Plug your microscope into the extension cords. Each group of desks uses the same cord. 3. Always start and end with the Low Power Objective. Do not remove slides with the high power objective in place - this will scratch the lens! Microscopes should be stored with the low power objective in place. 4. Always wrap electric cords and cover microscopes before returning them to the cabinet.

5. Always carry microscopes holding the Arm and Base and set them flat on your desk.

. Always use lens paper to clean slides and lenses.

The Compound Microscope Proper use and care of microscope

Focusing Specimens Always start with the Low Power objective. Use the Coarse Adjustment to focus initially. Image may be small at this magnification, but you won't be able to find it on the higher power without this first step. Do not use stage clips, try moving the slide around until you find something. ALWAYS LOOK FROM SIDE WHEN CLICKING OBJECTIVES IN PLACE

2. Once you've focused on Low, switch to Medium Power 2. Once you've focused on Low, switch to Medium Power. Use the Coarse Knob to refocus. Again, if you haven't focused on this level, you will not be able to move to the next level. 3. Now switch to High Power. (If you have a thick slide, or a slide without a cover, do NOT use the high power objective). At this point, ONLY use the Fine Adjustment to focus specimens. Only use fine adjustment to focus on high power. 4. If the specimen is too light or too dark, try adjusting the diaphragm. 5. If you see a line in your viewing field, try twisting the eyepiece, the line should move. That's because its a pointer, and is useful for pointing out things to your lab partner or teacher.

Troubleshooting Occasionally you may have trouble with working your microscope. Here are some common problems and solutions. Image is too dark! Adjust the diaphragm, make sure your light is on. 2. There's a spot in my viewing field, even when I move the slide the spot stays in the same place! Your lens is dirty. Use lens paper, and only lens paper to carefully clean the objective and ocular lens. The ocular lens can be removed to clean the inside. 3. I can't see anything under high power! Remember the steps, if you can't focus under low and then medium power, you won't be able to focus anything under high power. You need to return to the previous power and try refocusing.

Use pencil - you can erase and shade areas Drawing Specimens Use pencil - you can erase and shade areas 2. All drawings should include clear and proper labels (and be large enough to view details). Drawings should be labeled with the specimen name and magnification. 3. Labels should be written on the outside of the circle. Make lines using a ruler. The circle indicates the viewing field as seen through the eyepiece, specimens should be drawn to scale (ex. if your specimen takes up the whole viewing field, make sure your drawing reflects that. )

Making a Wet Mount Gather a thin slice/piece of whatever your specimen is. If your specimen is too thick, then the coverslip will wobble on top of the sample like a see-saw, and you will not be able to view it under High Power. 2. Place ONE drop of water directly over the specimen. If you put too much water, then the coverslip will float on top of the water, making it hard to draw the specimen, because they might actually float away. (Plus too much water is messy) 3. Place the coverslip at a 45 degree angle (approximately) with one edge touching the water drop and then gently let go. Performed correctly the coverslip will perfectly fall over the specimen. Tap on coverslip with eraser to get rid of air bubbles (use paper towels to remove excess water from slide

How to Stain a Slide Place one drop of stain (iodine, methylene blue..there are many kinds) on the edge of the coverslip. Place paper towel on the opposite side of the coverslip,. The paper towel will draw the water out from under the coverslip, and the cohesion of water will draw the stain under the slide. As soon as the stain has covered the area containing the specimen, you are finished. The stain does not need to be under the entire coverslip. If the stain does not cover as needed, get a new piece of paper towel and add more stain until it does. Be sure to wipe off the excess stain with a paper towel.

CLEAN UP! Store microscopes with the low objective in place. Wrap cords and cover microscopes. Wash slides in the sinks and dry them, placing them back in the slide boxes to be used later. Throw coverslips away.