Click a hyperlink or folder tab to view the corresponding slides. Analyzing Data Section 2.1 Units and Measurements Section 2.2 Scientific Notation and Dimensional Analysis Section 2.3 Uncertainty in Data Section 2.4 Representing Data Click a hyperlink or folder tab to view the corresponding slides. Exit Chapter Menu

Section 2.1 Units and Measurements Define SI base units for time, length, mass, and temperature. Explain how adding a prefix changes a unit. Compare the derived units for volume and density. mass: a measurement that reflects the amount of matter an object contains Section 2-1

Section 2.1 Units and Measurements (cont.) base unit second meter kilogram kelvin derived unit liter density Chemists use an internationally recognized system of units to communicate their findings. Section 2-1

Units Système Internationale d'Unités (SI) is an internationally agreed upon system of measurements. A base unit is a defined unit in a system of measurement that is based on an object or event in the physical world, and is independent of other units. Section 2-1

Units (cont.) Section 2-1

Units (cont.) Section 2-1

Units (cont.)

Units (cont.) Chocolate Milk

Kangaroos Have Died Drinking Units (cont.) Kangaroos Have Died Drinking Chocolate Milk!!!!!!!!!!!!!!!!!! Kilo Hecto Deka 1 Deci Centi Milli

The SI base unit of mass is the kilogram (kg), about 2.2 pounds Units (cont.) The SI base unit of time is the second (s), based on the frequency of radiation given off by a cesium-133 atom. The SI base unit for length is the meter (m), the distance light travels in a vacuum in 1/299,792,458th of a second. The SI base unit of mass is the kilogram (kg), about 2.2 pounds Section 2-1

The SI base unit of temperature is the kelvin (K). Units (cont.) The SI base unit of temperature is the kelvin (K). Zero kelvin is the point where there is virtually no particle motion or kinetic energy, also known as absolute zero. Two other temperature scales are Celsius and Fahrenheit. K = 0C + 273 Section 2-1

Not all quantities can be measured with SI base units. Derived Units Not all quantities can be measured with SI base units. A unit that is defined by a combination of base units is called a derived unit. Section 2-1

Derived Units (cont.) Volume is measured in cubic meters (m3), but this is very large. A more convenient measure is the liter, or one cubic decimeter (dm3). Section 2-1

Density is a derived unit, g/cm3, the amount of mass per unit volume. Derived Units (cont.) Density is a derived unit, g/cm3, the amount of mass per unit volume. The density equation is density = mass/volume D = M / V Section 2-1

A B C D Section 2.1 Assessment Which of the following is a derived unit? A. yard B. second C. liter D. kilogram A B C D Section 2-1

A B C D Section 2.1 Assessment What is the relationship between mass and volume called? A. density B. space C. matter D. weight A B C D Section 2-1

End of Section 2-1

Section 2.2 Scientific Notation and Dimensional Analysis Express numbers in scientific notation. Convert between units using dimensional analysis. quantitative data: numerical information describing how much, how little, how big, how tall, how fast, and so on Section 2-2

Section 2.2 Scientific Notation and Dimensional Analysis (cont.) conversion factor Scientists often express numbers in scientific notation and solve problems using dimensional analysis. Section 2-2

Scientific Notation Scientific notation can be used to express any number as a number between 1 and 10 (the coefficient) multiplied by 10 raised to a power (the exponent). Count the number of places the decimal point must be moved to give a coefficient between 1 and 10. Section 2-2

Scientific Notation (cont.) The number of places moved equals the value of the exponent. The exponent is positive when the decimal moves to the left and negative when the decimal moves to the right. 800 = 8.0  102 0.0000343 = 3.43  10–5 Section 2-2

Dimensional Analysis Dimensional analysis is a systematic approach to problem solving that uses conversion factors to move, or convert, from one unit to another. A conversion factor is a ratio of equivalent values having different units. Section 2-2

Dimensional Analysis (cont.) Writing conversion factors Conversion factors are derived from equality relationships, such as 1 dozen eggs = 12 eggs. Percentages can also be used as conversion factors. They relate the number of parts of one component to 100 total parts. Section 2-2

Dimensional Analysis (cont.) Using conversion factors A conversion factor must cancel one unit and introduce a new one. Section 2-2

A B C D Section 2.2 Assessment What is a systematic approach to problem solving that converts from one unit to another? A. conversion ratio B. conversion factor C. scientific notation D. dimensional analysis A B C D Section 2-2

A B C D Section 2.2 Assessment Which of the following expresses 9,640,000 in the correct scientific notation? A. 9.64  104 B. 9.64  105 C. 9.64 × 106 D. 9.64  610 A B C D Section 2-2

End of Section 2-2

Section 2.3 Uncertainty in Data Define and compare accuracy and precision. Describe the accuracy of experimental data using error and percent error. Apply rules for significant figures to express uncertainty in measured and calculated values. experiment: a set of controlled observations that test a hypothesis Section 2-3

Section 2.3 Uncertainty in Data (cont.) accuracy precision error percent error significant figures Measurements contain uncertainties that affect how a result is presented. Section 2-3

Accuracy and Precision Accuracy refers to how close a measured value is to an accepted value. Precision refers to how close a series of measurements are to one another. Section 2-3

Accuracy and Precision (cont.) Percent error expresses error as a percentage of the accepted value. % Error = │exp – acc │ (100) acc Section 2-3

Often, precision is limited by the tools available. Significant Figures Often, precision is limited by the tools available. Significant figures include all known digits plus one estimated digit. Section 2-3

Significant Figures Pacific - Atlantic Rule for Significant Digits If the decimal is present, start on the Pacific side (left) at the first nonzero digit and count it and all the digits to the right of it. If the decimal is absent, start on the Atlantic side (right) at the first nonzero digit and count it and all the digits to the left of it.

Rounding Numbers (cont.) Addition and subtraction Round numbers so the final answer has the same number of decimal places as the measurement with the least number of decimal places. Multiplication and division Round the answer to the same number of significant figures as the original measurement with the fewest significant figures. Section 2-3

A B C D Section 2.3 Assessment Determine the number of significant figures in the following: 8,200, 723.0, and 0.01. A. 4, 4, and 3 B. 4, 3, and 3 C. 2, 3, and 1 D. 2, 4, and 1 A B C D Section 2-3

A B C D Section 2.3 Assessment A substance has an accepted density of 2.00 g/L. You measured the density as 1.80 g/L. What is the percent error? A. 0.20 g/L B. –0.20 g/L C. 0.10 g/L D. 0.90 g/L A B C D Section 2-3

End of Section 2-3

Section 2.4 Representing Data Create graphics to reveal patterns in data. independent variable: the variable that is changed during an experiment Interpret graphs. graph Graphs visually depict data, making it easier to see patterns and trends. Section 2-4

Graphing A graph is a visual display of data that makes trends easier to see than in a table. Section 2-4

Graphing (cont.) A circle graph, or pie chart, has wedges that visually represent percentages of a fixed whole. Section 2-4

Graphing (cont.) Bar graphs are often used to show how a quantity varies across categories. Section 2-4

Graphing (cont.) On line graphs, independent variables are plotted on the x-axis and dependent variables are plotted on the y-axis. Section 2-4

Interpreting Graphs Interpolation is reading and estimating values falling between points on the graph. Extrapolation is estimating values outside the points by extending the line. Section 2-4

Interpreting Graphs (cont.) This graph shows important ozone measurements and helps the viewer visualize a trend from two different time periods. Section 2-4

A B C D Section 2.4 Assessment ____ variables are plotted on the ____-axis in a line graph. A. independent, x B. independent, y C. dependent, x D. dependent, z A B C D Section 2-4

A B C D Section 2.4 Assessment What kind of graph shows how quantities vary across categories? A. pie charts B. line graphs C. Venn diagrams D. bar graphs A B C D Section 2-4

End of Section 2-4

Standardized Test Practice Image Bank Concepts in Motion Chemistry Online Study Guide Chapter Assessment Standardized Test Practice Image Bank Concepts in Motion Resources Menu

Section 2.1 Units and Measurements Key Concepts SI measurement units allow scientists to report data to other scientists. Adding prefixes to SI units extends the range of possible measurements. To convert to Kelvin temperature, add 273 to the Celsius temperature. K = °C + 273 Volume and density have derived units. Density, which is a ratio of mass to volume, can be used to identify an unknown sample of matter. Study Guide 1

Section 2.2 Scientific Notation and Dimensional Analysis Key Concepts A number expressed in scientific notation is written as a coefficient between 1 and 10 multiplied by 10 raised to a power. To add or subtract numbers in scientific notation, the numbers must have the same exponent. To multiply or divide numbers in scientific notation, multiply or divide the coefficients and then add or subtract the exponents, respectively. Dimensional analysis uses conversion factors to solve problems. Study Guide 2

Section 2.3 Uncertainty in Data Key Concepts An accurate measurement is close to the accepted value. A set of precise measurements shows little variation. The measurement device determines the degree of precision possible. Error is the difference between the measured value and the accepted value. Percent error gives the percent deviation from the accepted value. error = experimental value – accepted value Study Guide 3

Section 2.3 Uncertainty in Data (cont.) Key Concepts The number of significant figures reflects the precision of reported data. Calculations should be rounded to the correct number of significant figures. Study Guide 3

Section 2.4 Representing Data Key Concepts Circle graphs show parts of a whole. Bar graphs show how a factor varies with time, location, or temperature. Independent (x-axis) variables and dependent (y-axis) variables can be related in a linear or a nonlinear manner. The slope of a straight line is defined as rise/run, or ∆y/∆x. Because line graph data are considered continuous, you can interpolate between data points or extrapolate beyond them. Study Guide 4

A B C D Which of the following is the SI derived unit of volume? A. gallon B. quart C. m3 D. kilogram A B C D Chapter Assessment 1

A B C D Which prefix means 1/10th? A. deci- B. hemi- C. kilo- D. centi- A B C D Chapter Assessment 2

Divide 6.0  109 by 1.5  103. A. 4.0  106 B. 4.5  103 C. 4.0  103 D. 4.5  106 A B C D Chapter Assessment 3

A B C D Round the following to 3 significant figures 2.3450. A. 2.35 Chapter Assessment 4

A B C D The rise divided by the run on a line graph is the ____. A. x-axis B. slope C. y-axis D. y-intercept A B C D Chapter Assessment 5

A B C D Which is NOT an SI base unit? A. meter B. second C. liter D. kelvin A B C D STP 1

A B C D Which value is NOT equivalent to the others? A. 800 m B. 0.8 km C. 80 dm D. 8.0 x 105 cm A B C D STP 2

Find the solution with the correct number of significant figures: 25  0.25 STP 3

A B C D How many significant figures are there in 0.0000245010 meters? STP 4

A B C D Which is NOT a quantitative measurement of a liquid? A. color B. volume C. mass D. density A B C D STP 5

Click on an image to enlarge. IB Menu

IB 1

IB 2

IB 3

IB 4

IB 5

IB 6

IB 7

IB 8

IB 9

IB 10

IB 11

IB 12

Figure 2.10 Accuracy and Precision Table 2.2 SI Prefixes Figure 2.10 Accuracy and Precision CIM

Click any of the background top tabs to display the respective folder. Within the Chapter Outline, clicking a section tab on the right side of the screen will bring you to the first slide in each respective section. Simple navigation buttons will allow you to progress to the next slide or the previous slide. The Chapter Resources Menu will allow you to access chapter specific resources from the Chapter Menu or any Chapter Outline slide. From within any feature, click the Resources tab to return to this slide. The “Return” button will allow you to return to the slide that you were viewing when you clicked either the Resources or Help tab. To exit the presentation, click the Exit button on the Chapter Menu slide or hit Escape [Esc] on your keyboards while viewing any Chapter Outline slide. Help

This slide is intentionally blank. End of Custom Shows