Welding, Cutting, and Brazing

Notice This presentation is provided to all Educational Service District 101 (ESD 101) schools at no cost. This presentation contains copyrighted materials purchased by ESD 101 for the exclusive use of training school personnel within ESD 101. This presentation may not be reproduced except to print “handouts” or “notes pages” for use during training within ESD 101 school districts. If the school district does not have Microsoft’s PowerPoint software available, a PowerPoint viewer can be downloaded from the internet at no cost. Questions may be directed to the ESD 101 Risk Manager.

Welding Safety Program Guidelines Determine who is accountable for enforcement of welding operations Hot work permitting system Perform a job hazard assessment of welding equipment

Welding Safety Program Guidelines Special procedures for equipment used in welding process Care of cylinders Ventilation systems Fire prevention

Welding Safety Program Guidelines Engineering controls Administrative controls Personal protective equipment Equipment inspection and maintenance Incident investigation

Welding Hazards Damage to eyes and skin Ultraviolet (UV) rays Infrared rays Purging and cleaning of closed containers prior to welding operations

Welding Hazards Toxic gases, fumes, and dusts Fire hazards from welding and cutting operations

Welding Hazards Metal splatter Electric shock Explosion hazards

General Safe Work Practices Use a platform with toeboards when working from elevated surfaces Protect workers from stray sparks or slag in areas below elevated work surfaces

General Safe Work Practices Warn others of hot metal by marking work areas Keep floor areas clear of electrodes and/or electrode stubs

General Safe Work Practices Never use bare conductors, damaged regulators, torches, or electrode holders Never arc weld or resist weld while standing on damp surfaces

General Safe Work Practices Keep fire extinguishers near areas where hot work is performed

Compressed Gas Cylinder Handling and Storage Never accept compressed gas cylinders (CGCs) that were shipped in a horizontal position Store CGCs upright Keep CGCs secured with chains or cables

Compressed Gas Cylinder Handling and Storage Group cylinders by type of gas Store full and empty cylinders apart Store gases so that old stock is removed and used first

Compressed Gas Cylinder Handling and Storage Keep protective caps on stored CGCs Prevent the dropping or banging of CGCs Don’t roll CGCs along the bottom rim

Compressed Gas Cylinder Handling and Storage Don’t lift CGCs by the cap unless using hand trucks designed for this purpose Prevent cylinders from falling, or from having objects fall on them

Compressed Gas Cylinder Handling and Storage Ensure that valves, hoses, connectors, and regulators are in good condition

Compressed Gas Cylinder Handling and Storage Never open valves until regulators are drained of gas and pressure adjusting devices are released When empty, close and return CGCs to the vendor

Compressed Gas Cylinder Handling and Storage Empty CGCs must be labeled “MT” or “Empty” Keep oil and grease away from oxygen CGCs, valves, and hoses

Fire Watches for Welding Operations

Designate a Fire Watch When These Conditions Exist Combustible material is within 35 feet of the point of operation Combustibles are more than 35 feet away, but are easily ignited by sparks

Designate a Fire Watch When These Conditions Exist Wall or floor openings within a 35-foot radius expose combustible material in adjacent areas Combustible materials opposite of walls or ceilings can be ignited by conduction or radiation

Fire Watchers Will… Have fire extinguishers readily available, and be trained in their use Be familiar with alarm systems and their operation in the event of a fire

Fire Watchers Will… Watch for fires in all exposed areas Only try to extinguish fires obviously within the capacity of the equipment

Fire Watchers Will… Stay in hot work areas for at least one half hour after hot work operations have ceased to detect and extinguish smoldering fires

Welding Safety in Confined Spaces Before entry, test the work space for the following types of hazards: Flammability Combustibility Toxic fumes Slippery floor surfaces

Welding Safety in Confined Spaces When and where applicable, wear respiratory protection and a safety harness attached to a lifeline

When Hot-Work in a Confined Space is Interrupted Disconnect power to arc welding or cutting equipment Remove electrodes from holders Turn off torch valves

When Hot-Work in a Confined Space is Interrupted Turn off gas supply to gas welding and cutting units at a point outside the space Remove the torch and hose from the confined space, if possible

Make Housekeeping a Priority Keep welding areas free of combustibles Ensure proper storage of compressed gas cylinders

Don’t Take Shortcuts Getting the job done safely is the first consideration Always evaluate the job and implement appropriate safety precautions