Brick Kiln A kiln is a thermally insulated chamber, or oven, in which a controlled temperature regime is produced. Uses include the hardening, burning.

Slides:



Advertisements
Similar presentations
Development of a wood-fired cooking stove to incorporate a thermo-acoustic engine-generator unit Ron DennisProf. Keith PullenCity UniversityLondon.
Advertisements

What is Thermal Energy?.
HVAC523 Heat Sources.
[Asst.Prof. Mechanicl Engg. Dept.] [Electrical Engineering Department]
Different methods of energy conservation
Furnaces also called Fired Heaters
Boilers Dept. of Mech & Mfg. Engg..
ACTIVE LEARNING PROCESS Prepared By : BHATT HARSHIT 13BEECM026 SOLANKI KAUSHAL 13BEECM033 Guided By : Prof. J M Panchal Branch: Electronics & Communication.
INTRODUCTION. Seminar on IMPROVEMENT OF THERMAL EFFICIENCY BY RECOVERY OF HEAT FROM IC ENGINE EXHAUST.
CLAY VOCABULARY.
Energy Efficient Process Heating. Energy Balance on Furnace.
Design Steps : Furnace Of A Steam Generator P M V Subbarao Professor Mechanical Engineering Department Selection of Geometric Parameters….
Watertube Boiler.
Thermal Power Station Plant. Introduction 150 MW Thermal power station plant, produce 450t/hr steam at full load The max steam pressure is 150 bar with.
THERMAL POWER PLANT.
Building Methods Types of Structure.
© 2006 ITT Educational Services Inc. CD230 Architectural Design & Drafting: Unit 8 Slide 1 Unit 8 Fireplace and Stair Details.
Greenhouse and Aquaculture Design considerations John W. Lund Geo-Heat Center Oregon Institute of Technology Klamath Falls, OR
Chapter 5: Designing for Heating and Cooling 5.1 Organizing the problem a) Fenestration How much is optimum for the building? What should the form of the.
Chapter 6 Thermal Energy
Steam Boilers UNIT-VI.
Section 16.3 Using Heat.
Bricks Introduction Structural member Load transfer medium
Coal Burning System.
POWER PLANT.
STEAM CONDENSERS.
Topic C1 Superstructures - walls
Theory of Steam Generation P M V Subbarao Professor Mechanical Engineering Department Progressive Development of Power Generation through Steam Generation……
X. INCREASING TEMPERATURE - HEATING A. Heating system requirements –Optimum inside temperature –Uniform temperature –Prevent hot air on plants –Low cost.
Steam Power Station Presented By Ashvin G. Patel Asst. Prof. (E.E.)
Prefabricated Timber Frame Construction
Diesel Power Plant Mr.B.Ramesh, M.E.,(Ph.D) By
AIR QUANTITY REQUIRED TO TRANSFER HEAT IN A FORCED AIR SYSTEM In all four mechanical systems considered, the transfer of heat, either by taking it out.
Why Buy It? Buying this house will show you the amount of money you could have in your wallet. Located in Boise, Idaho, it has an outstanding view of.
Heating Systems.
Fireplace Construction and Drafting Introduction u How many of you have a fireplace in your home? u Is it your major source of heating? u Fireplaces.
5.3 Essential Questions What are the first and second laws of thermodynamics? How does an internal combustion engine work? How does a refrigerator work?
Woodstoves 1 Woodstoves. Woodstoves 2 Question Which is more effective at heating a room: a black woodstove a shiny chrome-plated woodstove.
Chapter 38 Fireplace Construction and Layout. 2 Links for Chapter 38 Fireplace Terms Energy Efficiency Fireplace Section Related Web Sites Fireplace Elevations.
Generating Stations. Bulk electric power is produced by special plants known as generating stations or power plants. Depending upon the form of energy.
 There are two common meanings of the term "greenhouse effect". There is a "natural" greenhouse effect that keeps the Earth's climate warm and habitable.
STEAM POWER PLANTS.
Eight tips for burning wood. Tip 1 Air! The wood is utilised in the best way when the draught control is fully open and the flames are intense. That will.
A Seminar On Suratgarh Super Thermal Power Station (Raj.)
THERMAL POWER PLANT. INTRODUCTION : THERMAL POWER PLANTS CONVERT THE HEAT ENERGY OF COAL INTO ELECTRICAL ENERGY. COAL IS BURNT IN A BOILER WHICH CONVERTS.
GLASS. 1. Glass is an amorphous, hard, brittle, transparent or translucent, super cooled liquid of infinite viscosity. 2. Produced by fusing a mixture.
THERMAL POWER PLANT.
Alternative Firing Methods.
Chapter 24 Chimneys and Fireplaces Copyright Goodheart-Willcox Co., Inc. May not be posted to a publicly accessible website. Explain how masonry chimneys.
GCSE ENERGY; THERMAL ENERGY TRANSFER 2
Cooling System Get the engine up to optimum operating Temperature as quickly as possible and maintains it at that temperature. Controls the heat produced.
The Basics of Freestanding Pellet Stoves. Pellet stoves are independent heat sources run by electricity and fueled by pieces of recycled materials, such.
Content: Introduction A Simple Gas Turbine Plant & It’s Working Plant Layout Types according to Cycle 1. Open Cycle Gas Turbine Plants 2. Close Cycle.
Gas Turbine Power Plant
TYPES OF COMBUSTION CHAMBERS - CI Engines
Chapter No-5 STEAM CONDENSERS AND COOLING TOWERS Marks-16
 II THE ADVANTAGES OF ELECTRICITY
Cupola Furnace.
UNIT 6 Thermal Energy Section 2.
Recent Developments in the Clean Combustion of Coal
BRAYTON CYCLE AND EFFECT OF INTERCOOLING , REHEAT AND REGENRATION
MANUFACTURING OF BRICKS
POWER PLANT THERMAL POWER STATION.
5.3 notes What are the first and second laws of thermodynamics?
Bell work Predict whether leaving the refrigerator door open on a hot summer day will help to cool the kitchen.
STEAM CONDENSERS AND COOLING TOWERS Marks-16
Furnaces (also called Fired Heaters)
Asst. Lect. Shireen Hasan
Presentation transcript:

Brick Kiln A kiln is a thermally insulated chamber, or oven, in which a controlled temperature regime is produced. Uses include the hardening, burning or drying materials. Kilns are also used for the firing of materials, such as clay and other raw materials, to form ceramics (including pottery, bricks etc.) Types of Kilns There are two basic types of kilns: (1) Continuous kilns and (2) Intermittent kilns.  A continuous kiln, sometimes called a tunnel kiln, is a long structure in which only the central portion is directly heated. From the cool entrance, material is slowly transported through the kiln, and its temperature is increased steadily as it approaches the central, hottest part of the kiln. From there, its transportation continues and the temperature is reduced until it exits the kiln at near room temperature. A continuous kiln is the most energy-efficient, because heat given off during cooling is recycled to pre-heat the incoming ware.  In intermittent kiln, the material to be fired is loaded into the kiln. The kiln is sealed, and the internal temperature increased according to a schedule. After the firing process is completed, both the kiln and the material are cooled.

Updraft Kilns Downdraft Kilns  Downdraft kilns are designed to force the flame and heated air to circulate through the kiln. Flame is introduced at the bottom of the kiln and naturally flows upward. The construction forces the flame back downward, to exhaust at the bottom of the kiln.  Downdraft kilns consist of four main components: the firebox, the stack area, the damper, and the chimney. The addition of the chimney helps create draw, or air flow.  Updraft kilns are those in which the flame is introduced into the bottom of the kiln, at or below floor level, and exhausted out the top. Updraft kilns consist of three basic components: the firebox, the damper, and the stack area.  The firebox is where the flame enters. The damper is at the top of the kiln and controls the exhaust (and by association, the kiln's atmosphere). The stack area is where the pots are set and is between the firebox and damper.  Although an updraft kiln tends to be less fuel efficient than a downdraft kiln, most commercially built fuel-burning kilns are updrafts. This is mainly due to their simplicity to build, pack, and ship. Fig : Updraft kilns

The kiln can be made circular or elliptical in shape. It is constructed on dry land, by digging a trench, m wide, m deep, and m long. Gaps are left in the outer wall for easy assess to the trench during setting and drawing of bricks. The raw bricks to be fired are set in rows, two to three bricks wide, with holes in between that allow feeding of coal and a sufficient flow of air through the setting. A linking layer of bricks is made across the width of the kiln and half way up, to stabilize the setting. On top of the bricks, two layers of bricks, covered with ash or brick dust, seal the setting. A large piece of canvas, paper or metal sheet is placed vertically across the brick setting to block air from entering from the wrong side of the chimneys. The trench contains ,000 bricks at a time. Chimneys, m high, made of sheet metal, are placed on top of the brick setting. They are moved around as the firing progresses and they have to be light, so that the firing crew can carry them. In order to maintain sufficient draught and the chimneys are placed closer to the firing zone. Circular Bull's trench kilns use only one chimney, whereas the larger elliptical kilns need two chimneys. The firing in a Bull's trench kiln is continuous, day and night. Raw bricks are loaded and finished bricks are drawn all the time. The fuel saving is achieved by reusing part of the energy that is otherwise lost in intermittent kilns. The air for combustion is drawn through the already fired but still hot bricks. The cooling bricks transfer their heat to the combustion air, pre-heating it before it enters the firing zone. After combustion, the hot exhaust gases pass through the yet unfired bricks on their way to the chimneys. This pre-heats the bricks, so less fuel is needed to bring the bricks to the maximum temperature. Once every 24 hours the chimneys are moved forward 5 to 7 m. Daily output is ,000 bricks.

Design of a Bull’s Trench Kiln

Advantages of the Bull's Trench Kiln More fuel efficiency compared to intermittent kilns. Low initial investment. High capacity. Disadvantages of the Bull's Trench Kiln The kiln is fired continuously and has to be loaded with a constant number of bricks every day. This demands a good organization of the brick production, and the production cannot easily be adjusted to fluctuations in the brick market. The firing crew needs long time experience. Its moveable chimneys have a short working life. The moveable chimneys' exhaust temperature is high, causing a less than optimum firing condition and fuel economy.

The Hoffmann Kiln The Hoffmann kilns were in the form of a great circular ring chamber, with massive walls and a large chimney at the centre, to which underground radial flues converged from the inside walls of each of the twelve chambers. The chambers were barrel arched (like a railway tunnel), and in the roof arches there were several small feed holes through which fine coal could be fed into spaces made among the bricks to be fired. Around the outer wall or the kiln were the twelve openings for loading and unloading the individual firing chambers. These chambers were seperated from each other by very large metal dampers, that could be raised and lowered as the fire moved around the kiln from chamber to chamber. Once the kiln is lit it is allowed to go out, and the sequence of operation is continuous. With the kiln in full operation two chambers will be open, and the other ten sealed up at the door and by the inter connecting steel dampers. If the chambers are numbered from 1 to 12, then bricks are being unloaded from 12 and load in 1. The damper is closed between 1 and 12, but open between all other chambers. Air is drawn through the open door of 2 and through the bricks in 3, 4, 5, and 6, cooling them down and at the same time being heated itself. The temperatures of the chambers increase from 3 to 6, with the temperature at 6 being close to the firing temperature. Chamber 7 is being fired, with fuel being fed at intervals through the roof, which is immediately ignited by the hot air from 6. The products of combustion pass on to 8, 9, 10, and 11 drying and pre-firing the bricks in these chambers. In 8, the bricks are at the pre-firing stage, and in 11 they are going through the water smoking stage. From 11 the combustion gases pass through the flue and up the central chimney. All the other 11 flues from the other chambers are closed off with dampers. At regular intervals, the firing zone is moved forward and the corresponding changes made to the dampers between the chambers and into the chimney. The chambers being loaded and unloaded move forward in sequence, and this way heat is extracted from the cooling bricks and also from the hot combustion gases. Fig : The circular Hoffmann kiln

Advantages of Hoffman kilns  They are fuel efficient, because the direct stoking into the bricks and their use of waste heat to dry and preheat the raw bricks before firing..  They have the capacity to fire very large quantities of bricks evenly and with minimal wastage.  The use of the down or cross draught system, with the fuel being burnt at regular intervals amongst the bricks, provides an even firing throughout the kiln.  The firing is controllable by the use of the dampers and careful stoking.  A variety of biomass fuels can be used successfully, for example, sawdust and wood processing waste, rice husk etc. Disadvantages of Hoffman kilns  They have a large mass that absorbs a lot of heat as the firing zone moves forward through the cold kiln. This is compensated by the fact that some of the residual heat in the kiln and fired bricks is used to pre-heat the air for combustion.  They are expensive to built and require regular maintenance.  They occupy a lot of space; because of this the are often built in the clay pit after all the usable clay has been extracted, so as not to occupy large areas of clay reserves.  Direct stoking affects the quality of the bricks directly beneath the stoke holes. These bricks can be over fired and are usually discoloured. This can be avoided by incorporating firing trenches beneath the stoking holes, along the sides and in the centre of the firing chamber. These trenches contain the burning fuel and prevent localised brick spoilage in the kiln. The fitting of firing trenches, however, means that the capacity of the kiln is reduced to produce a higher quantity of evenly fired bricks.