Knuckle joint Applications: Elevator chains, valve rods, etc

Slides:

Advertisements

Similar presentations

Knock Down Fittings Product Design.

Advertisements

Types and Uses of Fasteners

Cylinder Design Cylinder Liner (Barrel) Design

Chp12- Footings.

FIG 01: ASSEMBLED COTTERED JOINT

Mechanical Department

THREE DIMENSIONAL EQUILIBRIUM OF RIGID BODIES

Threads and Fasteners Fasteners.

Mechanics of Materials – MAE 243 (Section 002) Spring 2008

A machine helps you do work by changing the amount or direction of the force you need to apply. There are six basic types of simple machines.

Remaining lectures Last lecture by Dr. Darpe: Wed, 3 rd Oct Lectures by Prof S R Kale 22 st Oct (Mon) 24 th Oct (Wed) and 31 st Oct (Wed) 11am – 11:55am.

Major Diameter: The largest diameter of the thread Minor Diameter: The smallest diameter of the thread Pitch: Distance between two threads (mm) or no of.

Specification section 3.3

Mechanical Methods of Joining

Screws, Fasteners, and the Design of Nonpermanent Joints

CM 197 Mechanics of Materials Chap 20: Connections

Copyright 2005 by Nelson, a division of Thomson Canada Limited FIGURES FOR CHAPTER 3 TORSION Click the mouse or use the arrow keys to move to the next.

Home Work #4 Due Date: 18 Mar, 2010 (Turn in your assignment at the mail box of S581 outside the ME general office) The solutions must be written on A4.

WELCOME IN SEM II. ASST. PROF. BHARAT CHAUDHARI DESIGN MANUFACTURING THERMAL.

MECHANICAL DRAWING Chapter 11: Threads Fasteners and Springs

CE7005 Prestressed Concrete

Axially loaded member Axial load and normal stress under equilibrium load, Elastic Deformation.

 What is joinery? In our case – we will be looking at the fastening or combining of two or more boards together when building our projects.  It is important.

Fasteners, Load and Stress. Loads Load is an engineering term for the forces that are exerted on a structure. Loads are considered either static or dynamic:

Drilling Machine Accessories

Group -5 Yash Shah, Shreya Bhanushali, Jay Bhavsar, Smit Kotadia,

Threads, Fasteners, and Springs Chapter Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson.

Keys · Keys connect functional parts of mechanisms and machines, allowing moving parts to transmit power or to locate parts relative to each other.

LINEAR MEASUREMENT.

Chapter 11 keys, coupling, and seals

Extra Examples.

Chapter 1: Stress Review important principles of statics

Section XI Keys, Pins, & Splines.

ENT 153 TUTORIAL 1.

STRENGTHS Chapter Intro Dealing with relationship between the external loads applied to an elastic body and the intensity of the internal forces.

LRFD-Steel Design Dr. Ali Tayeh Second Semester

1.5 AVERAGE SHEAR STRESS Shear stress is the stress component that act in the plane of the sectioned area. Consider a force F acting to the bar For rigid.

Chapter 10 Miscellaneous Types of Fasteners. Many different locking devices are used to prevent nuts from working loose. A screw thread holds securely.

MANUFACTURING TECHNOLOGY UNIT – V Machine Tools. Manufacturing Technology.

EMD223 Machine Component Design Dr. Mohamad Yusof Idroas Room: 3.10 (SoME) EMD223 Machine Component Design.

Real World Simple Machines By Chelsea Dehnke. Lever rigid object and a fulcrum (or pivot) Applying a force to one end of the rigid object causes it to.

ELEMENTS OF MECHANICAL ENGINEERING

Simple Machines There are 6 basic types. 1 - INCLINED PLANE An inclined plane is a flat, sloped surface How it works: *It increases distance and decreases.

Drawing of bolt and nut.

CHAPTER 12 THREADS, FASTENERS AND SPRING

TITLE A cotter is a flat wedge shaped piece of rectangular cross-section and its width is tapered (either on one side or both sides) from one end to.

1. Two rods, one of nylon and one of steel, are rigidly connected as shown in Fig. P.1.2. Determine the stresses and axial deformations when an axial load.

Design of shaft couplings

Design of Joints, Levers, & offset Links (12 marks)

Cotter and Knuckle Joints

Metalwork Threaded Fasteners.

FIG 01: ASSEMBLED COTTERED JOINT

ASSEMBLED COTTERED JOINT

Knuckle joint Applications: Elevator chains, valve rods, etc

CONNECTIONS IN STEEL STRUCTURES

Remaining lectures Last lecture by Dr. Darpe: Wed, 3rd Oct

MACHINE PARTS (FOR DCE / DIT)

Horizontal Milling Operations

Chapter 1 Stress and Strain.

Presentation on Engineering Drawing

G.B.N GOVT. POLYTECHNIC, NILOKHERI

Simple Machines Week 8 Notes

Wood Fasteners, Joinery, & Adhesives

Chapter 6 Design of Keys, Splines and Pins

MACHINE DRAWING NAME : SYED AMER UR RAHMAN B.TECH 2 – 2

Presentation transcript:

Knuckle joint Applications: Elevator chains, valve rods, etc Two or more rods subjected to tensile and compressive forces are fastened together Their axes are not in alignments but meet in a point The joint allows a small angular moment of one rod relative to another It can be easily connected and disconnected Applications: Elevator chains, valve rods, etc

Knuckle joint

Knuckle joint

Cotter joints A cotter joints is a flat wedge link piece of steel of rectangular cross section which is inserted through the rods at high angle to their axes .It is uniform in thickness but tapering in width , generally on one side only. Usually the taper is 1 in 30. when a special arrangement like a set-screw is provided for keeping the cotter from slackening ,its taper may be as large as 1 in 7. the end of the cotter are made narrow to facilitate the hammering for fixing and removing. cotter joins are generally use to fasten rigidly two rod s which is subjected to tensile or compressive stress along their axes. this joint is used to connect two circular rods. This joint in not suitable where the member are subjected under rotation. Thus they differ from key joints which are used to fasten shaft and hubs subjected to tensional stress:

Cotter joints with socket and spigot ends for circular bars Slots are wider than the cotter. Cotter pulls the rod and socket tightly together Clearance: must be provided for adjustment.(2 to 3 mm) Proportions cotter thickness = (1/3)diameter of rod cotter width = rod diameter

Cotter joint

Sleeve and cotter joint For circular rods The enlarged ends of the rods butt against each other with a common sleeve over them The rod ends are enlarged to take care of the weakening effect caused by slots

Cotter joint with a gib Gib and cotter joints are used for rods of square or rectangular cross section .the end of one rod fits the end of the other rod which is made in the form of a strap. A gib is used along with the cotter to make this joint. Gib is likely a cotter but with two gib heads at its ends . The thickness of the gib and cotter are same.

Gib and cotter joint for rectangular rods One bar end is made in the form of a strap A Gib is used along with the cotter. Gib is like a cotter but with two gib heads at its ends . The thickness of the gib and cotter are same

Gib and cotter joint or rectangular rods