1. MECHANICAL DRAWING Chapter 11: Threads Fasteners and Springs

2. Objectives of threads and fasteners
1. To hold parts together (Assembly).
2. To provide for adjustment between parts (Drum).
3. To transmit power

3. Define and label the parts of a screw thread
Chapter Objectives
Define and label the parts of a screw thread
Identify various screw thread forms.
Draw detailed, schematic, and simplified threads.
Define typical thread specifications
Draw various screw head types.
Draw springs

4. Screw Thread Nomenclature
External thread: a thread on the outside of a member (shaft).
Internal thread: a thread on the inside of a member (hole).
Major diameter: the largest diameter of the screw thread.
Minor diameter: the smallest diameter of the screw thread.
Pitch: the distance from a point on a screw thread to the corresponding point on the next thread measured parallel to the axis (US units = 1/ number of threads per inch).
Pitch diameter: the diameter of an imaginary cylinder passing through the threads where the widths of the threads and the width of the spaces are equal

5. Screw Thread Nomenclature
Lead: the distance that the screw advances in one turn.
Angle of a thread: the angle between the sides of the thread.
Crest: the outer surface of the thread
Root: the inner surface of the thread.
Side:
Axis of the screw:
From of the thread: the cross section of thread cut by a plane containing the axis
Series of thread: the standard number of threads per inch for various diameters.

6. Standardization of screw thread is very important
Important notes:
Thread Form:
International standard form (SI metric). Most widely used.
United States forms (English units). USA, Great Britain and Canada.
Standardization of screw thread is very important

7. Different number of threads per inch for various standard diameters
Screw Thread Forms
Sharp V thread: high friction because of full thread face.
American national: flatten roots and crests. General use. Replace by the following thread.
Unified thread (N): US standard thread (replaces the previous thread). Root is rounded, crest (rounded/flat).
Old standard US threads: (still included in the new standard - 11 series)
(UN or N); general.
(UNC or NC); course thread series.
(UNF or NF); fine thread series.
(UNS or NS); special series.
●) Unified extra fine series (UNEF)
Different number of threads per inch for various standard diameters

8. Screw Thread Forms
Metric thread (M): Standard (international screw thread fasteners ISO). Normally flat crest and root, could be rounded in external thread. Similar to the unified thread (lower depth).
Course thread (general purpose)
Fine thread
Square thread; power transmission (difficult to fabricate, and other problems). ACME thread is more used.
ACME thread: largely replaces the square thread.
●) Worm standard thread; similar to the ACME thread but deeper.

9. Screw Thread Forms
Whitworth thread: replaced by the unified thread (angle=55)
Knuckle thread: usually rolled from sheet metal. (Ex. Electrical bulbs and sockets, bottle tops, …etc).
Buttress thread: transmits power in one direction only. High strength requirements.
ASME standards == American Society of
Mechanical Engineers.

10. Right and Left-Hand Threads
Thread Pitch, Right and Left-Hand Threads & Single and Multiple Threads
Thread Pitch:
Right and Left-Hand Threads
Single and Multiple Threads

11. Drawing a Thread

12. Drawing a Thread
Simplified and Schematic Internal Thread symbols

13. Tables for Screw threads American and Metric

14. Tables for Screw threads American and Metric

15. Tables for Screw threads American and Metric

16. Detailed representation: External Metric, Unified, & American National Threads (DRAWING)

17. Simplified External and Internal Threads (DRAWING)

18. Schematic External and Internal Threads (DRAWING)

19. American National Thread Fits
A ≡ external thread
B ≡ internal thread
Class 1 fit: Clearance between mating parts is essential for rapid assembly, (1A, 1B).
Class 2 fit: High quality of commercial thread product, (2A, 2B).
Class 3 fit: Very high quality of commercial thread product (high cost), (3A, 3B)
Metric and Unified Thread Fits
g ≡ external thread
H ≡ internal thread
General-purpose application: (6H for internal, 6g for external) ≡ (2A, 2B).
Closer fit: (6H for internal, 5g6g for external)

20. Thread Notes

21. Thread Notes

22. Detailed representation: Internal Metric, Unified, & American National Threads (DRAWING)
Note that slope line is in the opposite direction of the external thread as you see internal threads!

23. Detailed representation: Internal Metric, Unified, & American National Threads (DRAWING)
Note that slope line is in the opposite direction of the external thread as you see internal threads!

24. Detailed External Square Thread

25. Detailed External Square Thread
Use the same table for square and acme threads

26. Detailed Internal Square Thread
Lines from crest to crest
Lines from root to screw axis

27. Detailed External ACME Thread

28. Phantom Lines and Threads in Assembly
For long threads use
phantom (hidden) lines
Threads in Assembly
Stud, bolt heads, and
nuts are not sectioned
External and internal
threads are shown in
V-shapes

29. One of the parts is threaded (no nut)
Bolts, Studs, and Screws
Threaded at both ends
Greater thread length
One of the parts is threaded (no nut)

30. Standard Bolts and Nuts
Inch and metric sizes
chamfered at 15-30o
Regular Heads & Bolts
(W = 1½D, H = ⅔D, T =⅞ D)
Heavy Heads & bolts
(structure)
(W = 1½D + ⅛" (3mm)
H = ⅔D, T = D)
See Table in Appendix 20 for standard bolts and nuts dimensions (no standard for bolt lengths)
Inch sizes only
Chamfered at 30o
(W = 1½D, H = ⅔D, T =⅞ D)
Thread Length:
Screws up to 6" length = 2D+¼" (6mm)
Screws over 6" length = 2D+½" (12mm)

31. Standard Bolts and Nuts
Across Corners
Across Flats

32. Hexagonal Bolts, Cap Screws, and Nuts (DRAWING)

33. Square Bolts, Cap Screws, and Nuts (DRAWING)

34. Standard Cap Screws
All screws except (e) can be drawn directly as in figures.
For exact dimensions see table (A21)

35. Standard Cap Screws

36. Standard Machine Screws (Smaller, Thread all the length)
All screws can be drawn directly as in figures.
For exact dimensions see table (A21)

37. Keys, Pins, and Rivets (Keys)

38. Keys, Pins, and Rivets (Keys)
Square or Flat Keys
Gib Head Key
Woodruff Keys and Key Slot Cutter
Pratt & Whitney Key

39. Keys, Pins, and Rivets (Keys Drawing)
Square and Flat Keys

40. Keys, Pins, and Rivets (Keys Drawing)
Gib Head Keys

41. Keys, Pins, and Rivets (Keys Drawing)
Pratt and Whitney Keys

42. Keys, Pins, and Rivets (Keys Drawing)
Woodruff keys

43. Keys, Pins, and Rivets (Keys Drawing)
Woodruff key solt

44. Keys, Pins, and Rivets (Machine Pins)
Taper Pin:
Used to fasten collars to shaft
Collars
See table A31 for standard diameters for given lengths

45. Keys, Pins, and Rivets (Rivets)
Usage:
Permanent fastening used to hold sheet metal or rolled steel together.
Made of wrought iron, carbon steel, copper, or other metals.
Hole diameter is slightly larger than the diameter of the rivet.
Rivet diameter d = to t: thickness of the sheet
A riveting machine is used to drive the rivet and forms the head on the plain end. This causes the rivet to swell and fill the hole tightly.
wrought iron = حديد مطاوع
Swell = become larger

46. Keys, Pins, and Rivets (Rivets)
Riveted Joints :

47. Springs (Types)

48. Springs (Representation/Drawing)
Schematic:

49. Springs (Representation/Drawing)
Detailed: