TECHNOLOGY AND ENGINERRING SKILL STUDY PROGRAM : BUILDING TECHNOLOGY SKILL COMPETENCE : DRAWING BUILDING TECHNOLOGY.

Slides:



Advertisements
Similar presentations
HULL FRAMING SYSTEMS by GROUP-E MEMBERS 1 JUDE RINALDO 2 AARYL D’SA
Advertisements

Chp12- Footings.
Summary Sheet Session Number : Date : Subject Expert : Dr. M.C. Nataraja Professor Department of Civil Engineering, S.J. College of Engineering,
Reinforced Concrete Design-8
Structural Components
1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore Mob:
SHEAR IN BEAMS. SHEAR IN BEAMS Example (4.1): A rectangular beam has the dimensions shown in Figure 4.12.a and is loaded with a 40 ton concentrated.
Lecture Goals Slab design reinforcement.
Department of Civil Engineering NED University Engineering & Technology Building Prof Sarosh Lodi.
Foundation Systems.
10 Chapter Floor Framing. 10 Chapter Floor Framing.
FLOOR CONSTRUCTION Meeting 8 Study Program: S0673 / Building Construction II Period: 2007.
Competency: Draw Foundation Plans
Teknologi Dan Rekayasa TECHNOLOGY AND ENGINERRING PROGRAM STUDI KEAHLIAN (SKILL DEPARTEMEN PROGRAME) : TEKNIK BANGUNAN (BUILDING TECHNOLOGY) KOMPETENSI.
COLUMNS. COLUMNS Introduction According to ACI Code 2.1, a structural element with a ratio of height-to least lateral dimension exceeding three used.
Teknologi Dan Rekayasa TECHNOLOGY AND ENGINERRING PROGRAM STUDI KEAHLIAN (SKILL DEPARTEMEN PROGRAM) : TEKNIK BANGUNAN (BUILDING TECHNOLOGY) KOMPETENSI.
Plain & Reinforced Concrete-1 CE-313
Reading Structural Drawings
Reinforced Concrete Design
1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore Mob:
Competency: Draw wall sections and details
Composite Construction
FLAT SLAB Flat slab are also known as beamless slab, is a type of slab in which the flooring slab is directly supported on columns without the agency of.
HULL FRAMING SYSTEMS GROUP B : SUNDEEP KULHARI PRASHANT KRISHNAN
On a floor plan of her room, the length of Hailey’s bed is 3 inches. If the scale of her floor plan is inch = 1 foot, what is the actual length of her.
BEAMS: Beams are structural members that can carry transverse loads which produce bending moments & shear force. Girders: Main load carrying members into.
Framed Structures Luisana Hernández.
Recommendations on Supports and Adjustment systems for ESS LINAC Components Fabien Rey Pawel Garsztka ESS Survey, Alignment and Metrology Group.
BUILDING CONSTRUCTION
SANKALCHAND PATEL COLLEGE OF ENGINEERING,
AR362 - Structural Systems In Architecture IV Lecture : Foundations
AHSANULLAH UNIVERSITY OF SCIENCE & TECHNOLOGY DEPT
Arranging Bugdget Plan of Construction Cost (RAB) Calculating construction RAB of House Building, water building and Bridge By: SMK NEGERI 5 SURAKARTA.
Teknologi Dan Rekayasa SHIELDED METAL ARC WELDING ADVANCE (SMAW) ADVANCE.
Index Temporary Works: No.Subject 1Timber Trenches 2Timber Scaffolding.
Teknologi Dan Rekayasa
Making picture of construction applying.
Competency: Repairing of CD Player
TECHNOLOGY AND ENGINERRING
Teknologi Dan Rekayasa TECHNOLOGY AND ENGINERRING
Identifying House Building Science
Teknologi Dan Rekayasa
TECHNOLOGY AND ENGINERRING
Making Picture of construction Application
Applying the basics of technical drawing
Competency: Draw wall sections and details
Identify the science building
Technological And Enginering
INDENTIFYING BODY PANEL/KOMPONEN TO BE REPAIRED
Teknologi Dan Rekayasa
Teknologi Dan Rekayasa TECHNOLOGY AND ENGINERRING
IMPLEMENTING PRE MOULDED CONCRETE JOB
TECHNOLOGY AND ENGINERRING
PLUMBING AND SANITATION ENGINEERING
MEASURES BY MEANS OF PRECISION MECHANIC MEASURE
786 Design of Two Way floor system for Flat Plate Slab
Introduction Used for covering spaces in the form of roof or floor
Identifying House Building science
Structural Design of Technology College in Hebron University
Applying Building Material Checking
Teknik Dasar Perkapalan
Slender Columns and Two-way Slabs
(i) proper arrangement of reinforcing bars and
SeminAR ON LINTELS --SANTHOSHKUMAR.M..,.
Competency: Draw wall sections and details
Building section A vertical cut or slice through a structure that illustrates the type of foundation, wall, and roof construction to be used.
Competency: Draw Foundation Plans
TOLMAN HALL RETROFIT POSSIBILITIES
An-Najah National University
Civil engineering drawing
Presentation transcript:

TECHNOLOGY AND ENGINERRING SKILL STUDY PROGRAM : BUILDING TECHNOLOGY SKILL COMPETENCE : DRAWING BUILDING TECHNOLOGY

Teknologi dan Rekayasa DRAWING A PLAN OF MAKING RE- ENFORCE CONCRETE Basic competence  To describe a frame of reenforced concrete  To design a frame of reenfoce concrete  To draw a map of setting frame of reenforced concrete  To draw a beam of setting frame of reenforced concrete  To make a list of a beam of reenforced concrete

Teknologi dan Rekayasa Drawing A plan of Reinforced Concrete Column A. DRAWING A BEAM OF BUILDING PROVIDED BY REINFORCED CONCRETE A column is a component of building frame that has duty to bear vertical burden. it is not in partial but the long unit. A short reinforced concrete bear any burden as well as no bending side part on the beam.

Teknologi dan Rekayasa Drawing A plan of Reinforced Concrete Column Giving reinforced concrete can strengthen the power of longitudinal bearing especially for the smaller part of the beam.

Teknologi dan Rekayasa Drawing A plan of Reinforced Concrete Column The frame of beam is frequently thinner. It brings about certain bend, flax or even more broken and collapse. So the beam should be given concrete construction.

Teknologi dan Rekayasa Drawing A plan of Reinforced Concrete Column The frame of beam is frequently thinner. It brings about certain bend, flax or even more broken and collapse. So the beam should be given concrete construction.

Teknologi dan Rekayasa Drawing A plan of Reinforced Concrete Column The re-enforced concrete should be provided by the literal construction to hinder the crump and the broken coating frame of the beam.

Teknologi dan Rekayasa Drawing A plan of Reinforced Concrete Column The edge of the beam should be given an angkur. The space between the begel along the the beam should be multiflied to the diameter of the smallest concrete in order that the frame of the concrete. To prevent the frame bent, you should set the concrete as close as possible so the scale can be covered the beam properly.

Teknologi dan Rekayasa Drawing A plan of Reinforced Concrete Column Technical requirements of a concrete the scale of concrete (should be at least like the following: – depth: 2,0 cm – width : 2,5 cm – invisible : 3,0 cm

Teknologi dan Rekayasa Drawing A plan of Reinforced Concrete Column Something important to take into consideration in drawing the reinforce column:  The connector of the beam is on the “sloof”  The column intervals of the beam on the middle side is more quite rare than those at the edge.  Those who have size about 30 cm should be widely given an extra concrete  The diameter of the main column is at least 12 mm)

Teknologi dan Rekayasa Drawing A plan of Reinforced Concrete Column B. Designing a plan of column structure of the concrete building To design concrete column is started from making a map and plan of allocate the column of the beam the column of concrete can be identified after counting the column we need.

Teknologi dan Rekayasa Drawing A plan of Reinforced Concrete Columns Steps of counting column of building concrete: 1.To define the amount of columns 2.To estimate the burden bearing by the concrete columns 3.To count momentary statement of columns 4.To estimate the concrete of columns 5.To estimate the powerful control of the burden that is likely stuck on the columns

Teknologi dan Rekayasa Drawing the map of setting the columns of reinforce structured building concrete C. Drawing the map of setting the columns of reinforce structured building concrete For example The map of setting concrete columns

Teknologi dan Rekayasa Drawing master plan of beaming the second floor and columns concrete setting 1. Drawing of a plan to beam the second floor and the column setting

Teknologi dan Rekayasa Map of foot plate, columns and “sloof”

Teknologi dan Rekayasa Map of foot plate, columns and concrete construction

Teknologi dan Rekayasa Map of foot plate, columns and concrete constructions

Teknologi dan Rekayasa Map of foot plate, columns and concrete constructions

Teknologi dan Rekayasa Map of foot plate, columns and concrete constructions

Teknologi dan Rekayasa Drawing A plan of Reinforced Concrete Columns  D. Drawing of a plan to beam the second floor and the column Setting The example column reinforce of building structure

Teknologi dan Rekayasa Drawing A plan of Reinforced Concrete Column

Teknologi dan Rekayasa Drawing A plan of Reinforced Concrete Column

Teknologi dan Rekayasa Drawing A plan of Reinforced Concrete Columns

Teknologi dan Rekayasa Drawing A plan of Reinforced Concrete Columns

Teknologi dan Rekayasa Drawing A plan of Reinforced Concrete Columns

Teknologi dan Rekayasa Drawing A plan of Reinforced Concrete Columns

Teknologi dan Rekayasa Drawing A plan of Reinforced Concrete Columns

Teknologi dan Rekayasa Drawing A plan of Reinforced Concrete Columns

Teknologi dan Rekayasa Drawing a map of concrete column

Teknologi dan Rekayasa Drawing A plan of Reinforced Concrete Column

Teknologi dan Rekayasa Drawing A plan of Reinforced Concrete Column

Teknologi dan Rekayasa Drawing A plan of Reinforced Concrete Columns

Teknologi dan Rekayasa Drawing A plan of Reinforce Concrete Column

Teknologi dan Rekayasa Drawing A plan of Reinforced Concrete Columns Thank you Compiled by : Rina D. Kania.S.Pd SMK Negeri 2 Tasikmalaya