Valve stem “gag” mechanism

Slides:

Advertisements

Similar presentations

Fasteners Mr. Lombardi. Fasteners Mr. Lombardi.

Advertisements

Michael Long– Eagle Project - Exhibit D-1 Plans/Drawings – Top View

Manual Flo-tap Installation Instructions

BRX210 ‘Mechanical Blueprint Reading’

Honda 450 Installation Manual.

ATD Assembly. ATD Assembly #1 Dewar Assembly #1 Status: Dewar has been completely assembled and vacuum tested. No vacuum leaks were detected on the outer.

10-3 Common Threaded Fasteners Machine screws have either fine or course threads and are available in a variety of heads. They may be used in tapped holes.

A New Stripline Connection to JPARC Horn 1 Larry Bartoszek BARTOSZEK ENGINEERING 9/23/04.

Hardware, Fasteners, Drills, and Thread Repair

Solenoid Pressure Regulator Check Valve Hand-turn Valve Pipe Clamp L-Bracket Mounting Block Plastic Tubing AN Fitting AN T-Fitting Pressure Sensor Base.

McMaster rail #6709K601 McMaster linear bearing #6709K180 with guide rail suppressed.

Gear Drive Flo-tap Installation Instructions Quick Installation Guides: rev. EA – 485 Flanged Flo-tap rev. DB – 485 Threaded.

Major Diameter: The largest diameter of the thread Minor Diameter: The smallest diameter of the thread Pitch: Distance between two threads (mm) or no of.

Tank Car Specialist Training Support Package November 2014 Module 9: Leak Repair.

Hoop Tech Clamp Assembly and Attachment. Contents of package.

Senior Design: Validation of Design December 15, 2008.

Threads and Fasteners.

General idea of a couple of check rod system and adjustments

LINAC LASER NOTCHER READINESS REVIEW August 5 th, 2014 Kevin Duel – Mechanical Support Engineer.

Vbine Energy Generator Assembly Pictures and Info Slide Show.

SubsystemCost Tanks and Containment$ Camera Positioning$ Pumping System $2, Common Header$ Pressure Control and Measurement$11,

Cylinder Head Motorcycle Engineering (021) Overhaul Cylinder Head (SK-KD – 04)

J-FRM-0101 Revision with Reason No.DateInitials Drawing No. D’Vinyl Inc. Descriptive Part Name Designed byChecked by Engineer Drawing Type Foot Plate Date.

Reverse Engineering: An Introduction.

VC Training Table Setup and Floating Agenda General –Air Supply Requirements Assembly –Assembling the System –Leveling the Table –Isolating.

Threads, Fasteners, and Springs Chapter Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson.

Plans for the 2015 Invention Challenge Target Paul MacNeal August 9,

Threaded Fasteners BOLTS, NUTS AND SCREWS. Threaded Fasteners Fastener is any device used to connect or join two or more parts/components. Fastener is.

14.52 in Attach the Axle to the chassis using the four (4) bolts, washers, and nylon lock nuts. Mount the tires. Note: The wheel recess outside on the.

New design With fewer parts and easier manufacture degrees 20mm 245.

Fundamentals of Structural Detailing

Frame Overview A36 Steel square tubing and plate Frame will rest on four wheels or two air skids 90” Long, 30” wide- outside CG envelope Two carts for.

Side view of generator. Close up of unused grounding pad - gives provisions for mounting the absorber.

Model 12 Intek Horizontal OHV

TAIL STOCK ASSEMBLY Modeled & Compiled by R.Rajashekar Asst. Professor Department of Mechanical Engineering U.V.C.E, Bangalore-1.

Motor Mounting MECH1200 Foot Mount: Simple and common Tabs or feet that are attached at the four corners of the motor and attaches to a bedplate. Sometimes.

½ ” steel plates 1/8 ” Steel C channels; 3 ½” inch wide each The Laser Holder Support Frame Geophone platforms (to characterize fixture motion) Stiffening.

Motor Propeller wrench Screw Nut (2) Cylinder top Tiny screw IGNORE:

½”-10”. Modification Overview  Production of the series began in 1989 and is current.

Date of download: 7/10/2016 Copyright © ASME. All rights reserved. Forearm Attachment for Postamputation Weight Lifting Exercise 1 J. Med. Devices. 2014;8(2):

CHAPTER 12 THREADS, FASTENERS AND SPRING

Common Woodworking Hand Tools

ENGINE MODE CODES.

Fasteners and Cold Metal

009 2½”-3”.

ME Contest Structure Plan View dia. orange circle

Far Detector Activities Late 2017 – Early 2018

HOW TO READ A TAPE MEASURE

Flag Installation on Roll-up Signs

Measure Hose as 14”, 12.5”, 12.25”, 9” & cut it.

Flag Installation on Roll-up Signs

NCB® Plating System Display

BASEPLATES SLIDE SHOW.

BASIC MECHANICAL FUNCTIONS

EML 2023 – Threads and Fasteners

BASIC MECHANICAL FUNCTIONS

Drawing of stud.

3000CIV 21/2”-10”.

McMaster linear bearing #6709K180 with guide rail suppressed

Wood and Metal fasteners

Assembling/Dismanteling Method of the Socket

Safety Practices: Cold Metal

EML 2023 – Threads and Fasteners

2000CIV 2½ ”-10”.

709 2½ ”-10”.

Presentation transcript:

Valve stem “gag” mechanism Valve stem “gag” mechanism. Same device will be used to clamp onto pipe cap, except the 2 bolts on top will be used to attach additional weight plates.

Clamp 4” Hole to clamp on to 1” pipe cap 5” Through holes for 3/8” bolts 1” Through holes for 3/8” -bolts

Half-Inch Weight Plate (1) 4” 5” Through holes for 3/8” bolts 0.5

One-Inch Weight Plate (3) 4” 5” Through holes for 3/8” bolts 1”

Assembly All parts will be assembled with 3/8” bolts (Grade 5 or better) and nuts. (Holes do not need to be tapped) Make parts from A36 steel