API Spec 6A Tensile Test Yield Offset Requirements

Slides:

Advertisements

Similar presentations

Byron Skillings, Ladish Proposed Rates: An Aerospace Perspective

Advertisements

Imagination at work API SC6 Resource Group On Materials Plenary Meeting Report Tim Haeberle June 19, 2014.

API Specification 6A Furnace Calibration Requirements

SC6 Ballot 1974: Adopt-back of ISO 10423:2009 as API 6A 20 th ed. Task Group Report on Resolution of Ballot Comments Eric Wehner 30 June 2010.

API6A718 Work Group Update February 6, API6A718 Work Group Meeting January 30, 2014.

API SC6 Winter Meeting New Business: API Spec 6A Tensile Test Specimen Requirements Tim Haeberle 8 February 2011.

API 6AV1 and API 6A Comparison

PH-DT Engineering Office, CERN

Given Connections Solution

Standard Practice for Reporting Data for Test Specimens Prepared by Additive Manufacturing This work is part of a larger project funded by the Advanced.

1 API Subcommittee 6 Plenary Meeting Resource Group on Materials Tim Haeberle Chairman – API SC6 Resource Group for Materials 6 February 2014.

Screws, Fasteners, and the Design of Nonpermanent Joints

1 API SC6 Winter Meeting Update on CSOEM MARG Activities Tim Haeberle Chief Consulting Engineer – Materials and Processes GE Oil & Gas 4 February 2015.

CSOEM MARG SUMMARY 24 June Meeting Tim Haeberle Chief Consulting Engineer – Materials and Processes GE Oil & Gas 24 June 2015.

API TG for 6A718 Inclusion of Additional Alloy 718 Strength Classes Rashmi Bhavsar 27 June 2013 Washington, DC.

New Item API Specification 6A Furnace Calibration Requirements Tim Haeberle 30 June 2011.

Tim Haeberle API SC Winter Meeting

Lesson 18 Casing Design Example

CSOEM Materials Advisory Group Summer Meeting: Status Update - UNS S66286 Elevated Temperature Tensile Testing Tim Haeberle Chief Consulting Engineer –

API Standard 6A718 Inclusion of Additional Alloy 718 Strength Classes

New Higher Strength Coiled Tubing Developed to Extend Coiled Tubing Operating Envelopes W. D. (Don) Van Arnam.

1 API SC6 Winter Meeting Other Materials Issues Tim Haeberle Chief Consulting Engineer – Materials and Processes GE Oil & Gas 4 February 2015.

SC6 Resource Group on Trees and Wellhead SC6 Winter Meeting 2012 Eric Wehner 22 February 2012.

Methods of Specifying ACT Objective Recognize the language, proper preparation, and appropriate situation for the four methods of specifying. 2.

Update on the API Work Group Activities on Pipe Markings.

Subcommittee on Heights, Massing, and Alternate Standards    Third Report – January 20, 2009 Planning & Zoning Commission.

Safety and quality issues – studs and nuts Presentation API 6A Winter meeting Feb

API Spec 6A Tensile Test Spec Reference Requirements Tim Haeberle API SC Summer Meeting.

Annual report TC67/SC4/WG3 Wellhead and Xmass tree ISO10423vs API 6A WG Scope:standardisation of wellhead and xmass trees plus valves WG convenor :Ries.

API Standard 6A718 Inclusion of Additional Alloy 718 Strength Classes – June Update Acceptance of alloy 718 at 140 ksi min yield strength Rashmi Bhavsar.

API SC6 Winter Meeting New Business: API Standard 6A718 – Inclusion of Additional Alloy 718 Strength Classes - Inclusion of Additional Alloys Tim Haeberle.

Other Party Management Team (OPMT) Status Briefing Americas Aerospace Quality Group (AAQG) Registration Management Committee (RMC) Tim Lee – Chair The.

Use of API 6A vs ISO in marking 6A equipment

Operational Excellence Quality and Customer Experience Operational Excellence Quality and Customer Experience SC-18 Liaison Report TG-3: Definition of.

Operational Excellence Quality and Customer Experience Operational Excellence Quality and Customer Experience SC18 Liaison report for SC6 Rick Faircloth.

SC17 Materials Initiatives 2015 Summer Meeting Update.

Annual report TC67/SC4/WG3 Wellhead and Xmass tree ISO10423 and API 6A WG Scope:standardisation of wellhead and xmass trees plus valves WG convenor :Ries.

Sub Committee 6 Ballot resolution Summary June 2012 Mike Briggs.

Tim Haeberle API SC Winter Meeting

API Spec 6A: ASME Section V And Section IX Reference Editions Tim Haeberle API SC Summer Meeting.

Reports / Updates From Task Groups / Liaisons Material Test Lab Calibration & Certification David Salgado reporting for Tim Haeberle 9 February 2010.

Ballot for WI 2361: The revision of the Total Elongation under load for the measurement of Grade C110 yield strength requires changing 0.6 to 0.7 in Tables.

Date of download: 6/2/2016 Copyright © ASME. All rights reserved. From: Technical Basis of Material Toughness Requirements in the ASME Boiler and Pressure.

TS Cool Down Studies TSu Unit Coils (24-25) N. Dhanaraj and E. Voirin Tuesday, 10 March 2015 Reference: Docdb No:

Imagination at work. Presented by Tim Haeberle Chief Consulting Engineer – Materials and Processes GE Oil & Gas 20 January 2016 API SC21 Austin, TX Status.

Operational Excellence Quality and Customer Experience Operational Excellence Quality and Customer Experience SC18 Liaison report for SC6 Rick Faircloth.

S.Movchan Straw manufacturing and QC

New Business – Proposal For Approval of SR3 For Addendum to API 6ACRA

Material Testing under Tension

Carry Over From API SC6 Winter Meeting API Standard 6A718 Inclusion of Additional Alloys Tim Haeberle 30 June 2011.

Carry Over From API SC6 Winter Meeting API Spec 6A Tensile Test Requirements Tim Haeberle 30 June 2011.

Carry Over From API SC6 Winter Meeting API Standard 6A718 Inclusion of Additional Alloy 718 Strength Classes Tim Haeberle 30 June 2011.

Tim Haeberle API SC Winter Meeting

WG Technical Editor’s Report

API 14L Specification for Lock Mandrels and Landing Nipples

API RP 17A - Discussion Points

May 26, 2014 EFFECT OF EXPLOSION CLADDING INDUCED HARDNESS ON SULFIDE STRESS CRACKING AND STRESS CORROSION CRACKING RESISTANCE OF INCONEL 625 Outline:

Specification on float equipment

SC6 Summer ’13 Meeting: WG 14H Update

Use of API 6A vs ISO in marking 6A equipment

Development of a specification

API Publication Types From “API Document Format and Style Manual” and “Procedures for Standards Development” the following are “standards” 1. Bulletin.

АВЛИГАТАЙ ТЭМЦЭХ ҮНДЭСНИЙ ХӨТӨЛБӨР /танилцуулга/

API SC 10 WG15 Stage Cementing Collars

OBD2CG OBD2 Phase 1 consolidated draft

API Specification 6A Keel Block Requirements New Item

Title : Alternative warm-up procedure WLTP rev1e by Japan

1. Get specs from customer Cost out the solution Decide discount strategy Assemble proposed response Approve proposed response.

API Specification 6A Keel Block Requirements

API 6A718 Work Group on Addition of Nickel Base CRAs

Presentation transcript:

API Spec 6A Tensile Test Yield Offset Requirements Tim Haeberle API SC6 2012 Summer Meeting

Need to fix in API version Background PROBLEM: The yield strength acceptance criteria for bodies, bonnets, and end and outlet connections is limited to the 0,2% offset method yield strength values in Table 6. This is good! However, for mandrel hangers it is up to the manufacturer to specify not only the yield strength in MPa (psi), but also the method of determining the yield strength. Unfortunately, if the manufacturer does not specify the method of determining the yield strength, methods other than the 0,2% offset method may be used, and these may give higher or lower values than would be obtained if the 0,2% offset method were used. Need to fix in API version

The Solution PROPOSED REVISION: 5.3.5.2 PSL 2 to 4 tensile testing (for mandrel tubing hangers and casing hangers) “b) test method: Perform tensile tests at room temperature in accordance with the procedures specified in ISO 6892-1 or ASTM A370. Perform a minimum of one tensile test. The results of the tensile test(s) shall satisfy the manufacturer’s specified requirements. The 0,2% offset method shall be used for determination of the yield strength”. JUSTIFICATION: A standardized method of determining the yield strength needs to be used for mandrel casing and tubing hangers.

API Ballot Ballot ready for SC6 to approve at the 2012 Summer Meeting for formal balloting

End Of Presentation

Backup Slides

Background CURRENT WORDING 5.3.5.2 PSL 2 to 4 tensile testing (for mandrel tubing hangers and casing hangers) “b) test method: Perform tensile tests at room temperature in accordance with the procedures specified in ISO 6892-1 or ASTM A370. Perform a minimum of one tensile test. The results of the tensile test(s) shall satisfy the manufacturer’s specified requirements.” 5.4.2.3 PSL 2 to 4 tensile testing (for bodies, bonnets, and end and outlet connections) Perform a minimum of one tensile test. The results of the tensile test(s) shall satisfy the applicable requirements of Table 6.” API 6A Table 6, column 2 (for bodies, bonnets, and end and outlet connections) “0,2% offset yield strength”.