1. Annual Refresher Training Tools and Machine Guards

2. Hazard Recognition Tools are common in “day-to-day” life Difficult to spot hazards due to familiarity Most tools manufactured with safety devices Users must inspect the tool daily Tools are often misused Tools and equipment used on the job can be dangerous devices. Even a simple hand tool can cause injury. Workers with little or no training are the highest risk for injury

3. Examples of Misuse Using a screwdriver as a chisel Using tools with loose handles Wrenches with sprung jaws

4. Hand Tools Safety Regular plastic dipped handles on hand tools are not for working on electrical equipment. If a wooden handle on a tool, such as a hammer or axe is loose, splintered or cracked, the head of the tool may dislodge from the handle. A wrench must not be used if its jaws are sprung. Impact tools, such as chisels, wedges or drift pins are unsafe if they have mushroomed heads. The heads may shatter on impact, causing sharp fragments to disperse

5. Power Tools Safety

6. Five Basic Rules with Power Tools Keep all tools regularly maintained Use the right tool for the job Examine each tool for damage before use Operate tools in accordance with the manufacturer Provide and use the proper personal protective equipment

7. Precautions Never place your finger on the start button while carrying a power tool. Never try to alter a tool to complete a task it was not designed for perform. Never remove a guard from a tool or machine. Be sure the power tool you need to use has a functioning guard. Properly tighten all nuts and bolts

8. Precautions, cont. Before You Plug it in, check for loose or frayed cords. Only use double-insulated or three- pronged plugs. Never carry a tool by the cord or hose Never yank the cord to unplug it Keep cords and hoses away form heat, oil, and sharp edges Disconnect tools when not in use

9. Precautions, cont Make sure observers at a safe distance Secure work with a vise or clamp Keep tools sharp and lubricated Do not wear loose clothes, ties, jewelry, etc. Mark or tag all damaged tools with “Do Not Use”

10. Personal Protective Equipment Use proper gloves when applying any chemical Wear the appropriate safety glasses/goggles when using hand tools Use the proper respirator when working with power tools that may produce respiratory hazards Spark shield and protection around flammables Don’t use tools near aisle ways

11. Equipment & Machine Safety Proper Tool Storage When finished using a power tool, disconnect it immediately from its power source Do not wrap the electric cord around the tool because it may cause the cord to wear or break Working at Heights Never work directly above someone. Do not carry tools up ladders, instead use a hoist or rope to lift your tools. Be aware of where your tools are at all times

12. Equipment & Machine Safety Operate them within their design limitations Gloves and footwear are recommended When they are not in use, store them in a dry location Do not use them in wet or damp location Work areas should be well lighted

13. Machine Guard

14. Protective Guards Guards are required for: Pinch, shear, or in-roll points. Shaft ends exposed more than ½ the diameter or have rough areas, such as gears, chains, pulleys, rope pulls and fan blades. Electrical circuits.

15. General Guard Safety Requirement Prevent body contact with dangerous moving parts Guards must be durable and firmly secured to the machine. Unplug the machine before attempting to conduct repairs. Never removed jammed objects by removing or working around the guard. Guards must protect objects from falling into moving parts. Guards must not create a hazard of its own, such as, shear points, jagged edges or any surface which could cause a laceration. Guards should not create interference or impede the worker from job performance. Properly maintain the machine according to manufacturer's instructions Always use proper lockout and tagout procedures

16. Guards Protect Against Guards will provide protection for operators from the following hazards: Point of operation In-running nip points Rotating parts Flying chips and sparks

17. Power Grinders Always use eye protection Turn off power when it is not in use Never clamp a hand-held grinder in a vise

18. ALL DONE! Make sure you fill out the quiz, sign it, and drop it off in my mailbox for record keeping. Remember: This is an annual requirement. SEE YOU NEXT YEAR

19. QUESTIONS? Contact: Kathie Moh 255-8849 kcm25@cornell.edu