1. J-FRM-0101 Revision with Reason No.DateInitials Drawing No. D’Vinyl Inc. Descriptive Part Name Designed byChecked by Engineer Drawing Type Foot Plate Date of This RevisionDrawing Issue Date Drawing SizeScale as DrawnScale as Printed Engineer Phone # Parts List QuantitySupplier Quantity Required 26 partA 8 x10 1:1, 1in=1in D. Quesnel 275-5215 02/27/99 1:1 =100% NOTES: Suitable for CNC Milling Material: Cold Roll Steel four per frame except six for process zone frame Total 4X5+6=26 Stock Finish OK ALL SURFACES Match Radii of 3.5” Square Tube Nominal Dimension so Foot fits and centers inside 3.5” square Tube Break sharp edges and corners All dimensions in inch units. Unless otherwise indicated, use default tolerances below x.x +/- 0.050” x.xx +/- 0.010” x.xxx +/- 0.005” Angles +/- 2 o 0.50 0.75 (stock Thickness) 3.50 Tap Through Hole 3/4 -10 3/16 Four Sides A A B B 1.75

2. J-FRM-0102 Revision with Reason No.DateInitials Drawing No. D’Vinyl Inc. Descriptive Part Name Designed byChecked by Engineer Drawing Type Foot Plate Assembly Date of This RevisionDrawing Issue Date Drawing SizeScale as DrawnScale as Printed Engineer Phone # Parts List QuantitySupplier Quantity Required 26 AssemblyA 8 x10 1:1, 1in=1in D. Quesnel 275-5215 02/27/99 1:1 =100% NOTES: 3/16 inch 6-32 pointed set screws Set Screws Must be on exterior surface and interior surface so both set screws are accessible after frames are butted together. Centering of Set screws is visual Center Break sharp edges and corners All dimensions in inch units. Unless otherwise indicated, use default tolerances below x.x +/- 0.050” x.xx +/- 0.010” x.xxx +/- 0.005” Angles +/- 2 o View of Bottom of Frame Leg Looking in Process Direction A A 1/8 Tap 6-32 Two Places Centered on Inside and Outside Faces Jam Nut 3/4-10 Hex Head Cap Screw-Grade 5 3/4 -10 1.5 inch Hex Head Cap Screw1 eachAny Vendor 3/4 -10 Jam Nut1 eachAny Vendor 6-32 pointed allen set screw, 3/16 length2 eachAny Vendor Foot Plate, J-FRM-01011 eachRCIMS

3. J-FRM-0103 Revision with Reason No.DateInitials Drawing No. D’Vinyl Inc. Descriptive Part Name Designed byChecked by Engineer Drawing Type Alignment Tab Date of This RevisionDrawing Issue Date Drawing SizeScale as DrawnScale as Printed Engineer Phone # Parts List QuantitySupplier Quantity Required 10 PartA 8 x10 1:1, 1in=1in D Quesnel D.Quesnel 275-5215 3/3/99 1:1 =100% Material: 1/2” Cold Rolled Steel Notes Two per framejoining 2X(6-1)=10 Holes 1.75 inch on centers Slot and Holes on Centerline Radius Nominal 1/8, 1/4” Mill Finish OK 2.00 0.750 1.00 6.75 1.75 4.25 2.50 0.44 (nominal 7/16) Through Drill Clearance for 3/8-24 A A Break sharp edges and corners All dimensions in inch units. Unless otherwise indicated, use default tolerances below x.x +/- 0.050” x.xx +/- 0.010” x.xxx +/- 0.005” Angles +/- 2 o 0.50 +.010 -.000 Tap for 1/4-20

4. J-FRM-0104 Revision with Reason No.DateInitials Drawing No. D’Vinyl Inc. Descriptive Part Name Designed byChecked by Engineer Drawing Type Alignment Tab Slider Date of This RevisionDrawing Issue Date Drawing SizeScale as DrawnScale as Printed Engineer Phone # Parts List QuantitySupplier Quantity Required ### PartA 8 x10 1:1, 1in=1in D. Quesnel 275-5215 3/3/992/2/99 1:1 =100% Material: Cold Rolled Steel Notes Holes 1.75 inch on centers Sliding fit into Slot in Alignment Tab Break sharp edges and corners All dimensions in inch units. Unless otherwise indicated, use default tolerances below x.x +/- 0.050” x.xx +/- 0.010” x.xxx +/- 0.005” Angles +/- 2 o 1.750 2.375 0.3125 Clearance for 3/8-24, Two Places 0.75 0.375 0.50 A A

5. J-FRM-0105 Drawing No. D’Vinyl Inc. Descriptive Part Name Designed byChecked by Engineer Drawing Type Alignment Tab Assembly Date of This RevisionDrawing Issue Date Drawing SizeScale as DrawnScale as Printed Engineer Phone # Parts List QuantitySupplier Quantity Required NA AssemblyA 8 x10 1:1, 1in=1in D Quesnel D. Quesnel 275-5215 3/3/99 1:1 =100% Notes All holes 1.75 inch on center Line of 3.5”Square Tube. -Use Drill Jig then tap holes for 3/8 -24 Bolt to Frame Just below lower Cross Member, inside frame. Use Allen Set Screw to Pull Frames Together. Spread Clamping Load to tab using washers Break sharp edges and corners All dimensions in inch units. Unless otherwise indicated, use default tolerances below x.x +/- 0.050” x.xx +/- 0.010” x.xxx +/- 0.005” Angles +/- 2 o Belville Washers 3/8-24 Allen Head Cap Screws Slider 1/4-20 Flat End Set Screw Height of Lower Cross Member Alignment Tab Junction of End Sections of adjacent Frames 1 J-FRM-0103 RCIMS 1 J-FRM-0104 RCIMS 4 1 inch outer Diameter Washer Any Vendor 4 3/8-24 Allen Head 5/8 Length Any Vendor Revision with Reason No.DateInitials 1.50 inches below to allow clearance for Weld