1. EMC Test Equipment - Amplifiers and Antennas George Barth Product Engineer, Systems ar rf/microwave instrumentation 160 School House Road Souderton, PA 18964-9990 gbarth@ar-worldwide.com gbarth@ar-worldwide.com

2. Topics G. Barth Ideal Amplifier Environment The EMC Reality Review of Amplifier Technologies Tube (Vacuum tube) Traveling Wave Tube (TWT) Amplifiers Solid-State: Different classes Amplifier Use Proper drive levels Loads

3. Topics G. Barth Amplifier Care and Maintenance Power and Field Measurements Antennas Technologies Applications Equipment Pairing and Sizing Power vs. Field

4. Ideal Conditions G. Barth What Amplifiers Love Always run in a low ambient room temperature ~72°F Use in a dust free environment Have clean power supplied Install in a fixed location by professionals Never exceed required input level depends on specification of each amplifier Never have a load fail Connect amplifier only to a matched load 50 Ω loads <1.5:1VSWR Only use fully tested and verified coax & waveguide

5. Ideal Conditions G. Barth Majority of the worlds amplifiers are designed for single uses. transmitters, cell phones, radios… These types of applications have known environmental conditions. Load is constant Frequency is usually narrowband Trained professionals are installing Environmental temperature constraints are known Amplifiers can be designed much more easily in these cases and are simple.

6. Less Than Ideal Conditions G. Barth EMC testing does not fall anywhere near ideal or simple conditions. The extremes for the EMC market High VSWR Amplifier is still required to deliver power or at a minimum not be damaged Bad loads, cables, connections Use in many tests, locations, and setups EMC Test engineers & technicians do not have to be amplifier experts

7. Less Than Ideal Conditions G. Barth What is needed Different engineering techniques are used to extend these constraints so the amplifier is more useful. Better heat removal for extended operating temperature range, which inherently extends the life of the amp Use better, more durable power supplies Rugged physical design Class A design Added VSWR protection (active protection) Added ability to handle VSWR

8. G. Barth Tube (Tetrode tube) TWT (Traveling Wave Tube) Amplifier Solid-state Class A Class AB Class B What are the differences? Amplifier Technologies

9. G. Barth Amplifier Technologies FET DC IV-Curve Operating Modes & Bias

10. G. Barth Amplifier Technologies FET DC IV-Curve Operating Modes & Bias Class A Class AB Class B

11. G. Barth Amplifier Technologies Class A

12. G. Barth Amplifier Technologies Class A

13. G. Barth Amplifier Technologies Class A

14. G. Barth Amplifier Technologies Class A

15. G. Barth Amplifier Technologies Class A Full current and voltage swing No harmonics

16. G. Barth Amplifier Technologies Class B Clipping High Harmonic content

17. G. Barth Amplifier Technologies Class AB

18. G. Barth Amplifier Technologies Class AB Good small signal response

19. G. Barth Amplifier Technologies Class AB

20. G. Barth Amplifier Technologies Class AB Clipping and Harmonics introduced

21. G. Barth Amplifier Technologies Class AB Shorted Harmonics

22. G. Barth Amplifier Technologies Class AB Shorted Harmonics

23. G. Barth Amplifier Technologies Class AB Shorted Harmonics Good small signal performance

24. G. Barth Amplifier Technologies Class AB Shorted Harmonics Self biasing

25. G. Barth Amplifier Technologies Class AB Shorted Harmonics Good performance due to self biasing limited to sub octave bandwidth

26. G. Barth Amplifier Technologies Amplifier Linearity 1dB point Harmonics at 1dB Harmonics above 1dB* Noise power density/ Spurious Ability to handle VSWR* Frequency coverage Tube Bad Good Worst Bad Best Low freq. <250 MHz TWTA Worst High freq. >1 GHz Solid state Class A Best Good Best Full coverage Solid state Class AB Bad Good Good to bad Full coverage Solid state Class B BadGood Bad Best Good to bad Full coverage * Results greatly depends on how the technology is implemented

27. G. Barth Amplifier Technologies Important specifications (other than the power, frequency, and VSWR protection you require) are linearity and harmonics, which are related. High harmonics may have undesirable effects on recorded test levels. As the amplifier approaches compression the harmonics increase. Class A solid state amplifiers seem to have the best performance even into compression. But large variations can be seen depending on the technology used. A recommended level is -6dBc of the field. Example: IEC 61000-4-3

28. G. Barth Compression Running the test while the amplifier is in compression will distort the test signal CW signal CW in compression Harmonics The compressed wave starts to resemble a square wave, producing higher harmonics.

29. G. Barth Compression Example of compressed power Compression points at one frequency

30. G. Barth What is the correct drive level to the amplifier? There will always be a max drive level before damage. Most of AR’s amps have +13dBm max input level. In most cases there is no reason to come even close to max input level. Amplifiers are rated with a 0dBm input to reach rated output. Most testing should not be done with saturated power Therefore -5 - -10 dBm may be all you need to drive the amplifier Amplifier Driving

31. G. Barth Amplifier Driving This brings us to the proper input to produce the desired linear output

32. G. Barth Amplifier Driving An amplifier requiring 0 dBm input to reach rated output does not mean 0dBm of input is required to get the results you may need. TWT amplifiers in some cases with a 0dBm input and full gain will be over driving the TWT. Over time this could be damaging. Application Note # 45 Input Power Requirements… For further explanation

33. G. Barth Amplifier & VSWR The amplifier’s ability to deal with VSWR will determine the possible use and application. TWTAs have a relatively low threshold to VSWR The TWT will fail at high VSWR without protection or precautions. 2:1 VSWR at rated power 1. Fold back at 20% reflected power (best) [AR] pulsed amps fold back at 50% reflected power [AR] 2. Shutdown at 2:1 VSWR 3. Rely on user to take responsibility to be proactive Low Power Solid State can have high threshold to VSWR Dependent on technology used Infinite VSWR handling, no protection needed [AR]

34. G. Barth Amplifier & VSWR High Power Solid State can have high threshold to VSWR Dependent on technology used High VSWR handling, some protection required Can handle up to 50% of rated power (6:1 VSWR) when used at full power Folds back so that reverse power does not exceed reverse power limit Why can’t higher power amplifiers handle infinite VSWR like lower power versions? Combining Components see up to twice the power (4x voltage and current) Combiners also act as splitters and direct energy back to output stages

35. Large Amplifier Makeup G. Barth Attenuator IN OUT Pre-amplification splitterscombiners Final stages

36. G. Barth Why is protection from mismatch needed? There is only so much that can be done to protect the amplifier without adding exorbitant cost Amplifier Technologies

37. G. Barth General care Keep original packaging for shipping If new packaging is required contact AR for suggestions Do not disconnect RF connection while amplifier is not in standby! The amplifier is protected from this but you are not! Make sure heat is not re-circulated back into amplifier Temperature is monitored and protected in the amplifier, but cooler is always better Care

38. G. Barth Tube [Vacuum tube] amplifiers Oil cooling system New unit: make sure to fill oil correctly. Do not tip over and place on it’s side to work on! Will drive full power and not fold-back into any load. Maintain recommended operating temperature. Over time tubes will slowly decrease power output and require replacement. Care

39. G. Barth TWTA TWT is most expensive part of the amplifier (Protect It) Make sure heat outtake and intake are not confined Be very careful not to overdrive input! This can be damaging to the TWT. Take care not to let the amplifier sit unused for extended periods of time [months – years]. The TWT will “Gas up”, then when activated the Tube may be damaged. A De-gassing start up routine needs to be used Do not leave the TWTA powered up and not being used for extended periods of time. Tube can “Gas up” Do not disable sleep mode feature Take care not to use badly mismatched loads AR’s amps are fully protected for all mismatches but is still stressful to TWT Care

40. G. Barth Solid-state Do what ever you want they can take it! Care

41. G. Barth Power and Field Measurement What is the proper way to measure power and field? What is the measurement device Power meter (w/directional coupler) Diode sensor Thermocouple sensor Peak power meter Field probe Diode sensor Thermocouple sensor Pulse probe Spectrum analyzer

42. G. Barth Power and Field Measurement Technology differences DiodeThermocouple More sensitive Can measure true RMS of a CW signal. Can be used to measure RMS of modulated signals if used within the linear region. Usually this is in the lower region but it’s difficult to know exactly. A signal in compression can have error in the actual reading. Faster response Less sensitive Less dynamic range Measures true RMS of any signal

43. G. Barth Power and Field Measurement Technology differences Broad-Band Device (power meter, field probe) Frequency Selective Device (Spectrum Analyzer) Will measure whole frequency spectrum including harmonics Care must be taken that harmonics are not contributing to reading Can be very accurate if used correctly Easy setup and use Can discern between different frequency signals Measures peak – RMS = Peak/SQRT(2) Can measure modulated signals Possible time consuming setup

44. G. Barth Power and Field Measurement For measuring amplifier output, using a directional coupler with a power meter is acceptable. Care should be taken in a reverberation chamber, for example. In most ALSE testing, forward power is a relative number and care only needs to be taken that this can be reproduced. If harmonics are a concern harmonic filters can be used.

45. G. Barth Power and Field Measurement Verify measurements are correct when using a broad-band device to take measurements It is a good idea to verify the readings are correct with a spectrum analyzer. 1.Run a calibration with the power meter and then a calibration with the spectrum analyzer to see if the forward power reading matches up 2.Use an antenna and spectrum analyzer to spot check V/m reading from probe during calibration especially where the amplifier is being driven hard. Don’t assume that if the harmonics are out of band that they are no longer a factor! (amplifier, probe, antenna…)

46. G. Barth E-Field Generator 10kHz-100MHz Field created between elements or elements and ground Non-radiating Power limited by Impedance Transformer Antennas

47. G. Barth Biconical (Bicon) 20MHz-300MHz Extremely broad beam width Power limited by Impedance Transformer (Balun) Antennas

48. G. Barth Log Periodic (LP) 26MHz-6GHz Beam width narrows with frequency Power limited by input connector and antenna feed Antennas

49. G. Barth Horn 200MHz-40GHz High Gain Beam width dependant on design Power limited by input connector or waveguide Antennas

50. G. Barth Pairing Considerations Frequency Antennas and Amplifiers do they match? Will switching be required? Power Can antenna handle amplifier power available? RF connectors compatible? Cabling? Equipment Pairing and Sizing

51. G. Barth Pairing Considerations Illumination of EUT 3dB beam width (test distance) Will windowing be required? Equipment Pairing and Sizing 28° 41° 74° 1.5 m 1 m 2 m 3 m

52. G. Barth Sizing Considerations Field Strength Test distance? Modulation? (AM, AM constant peak, Pulse) Losses Cables Chamber effects Reflections (EUT) VSWR (antenna) Margin Equipment Pairing and Sizing

53. G. Barth Calculating Power Required to Get Field Frequency dependant Equipment Pairing and Sizing

54. G. Barth Calculating Power Required to Get Field Frequency dependant Equipment Pairing and Sizing

55. G. Barth Calculating Power Required to Get Field Power calculated from graphs or formulas is P1dB Add for system losses Cables Chamber effects Reflections (EUT) VSWR (antenna) Add Margin Equipment Pairing and Sizing

56. G. Barth Any questions? Thank you for your attention!!! George Barth Product Engineer, Systems ar rf/microwave instrumentation 160 School House Road Souderton, PA 18964-9990 gbarth@ar-worldwide.com gbarth@ar-worldwide.com