1. Munira Bt Mohamed Nazari School of Bioprocess, UniMAP 2012
ERT VIBRATION
Munira Bt Mohamed Nazari
School of Bioprocess, UniMAP 2012
ERT 452

2. LECTURE 1: Fundamentals of Vibration
ERT 452

3. Topic Outline Introduction Basic Concepts of Vibration
Classification of Vibration
Vibration Analysis Procedure
Spring Elements
Mass or Inertia Elements
Damping Elements
Harmonic Motion
Harmonic Analysis
ERT 452

4. introduction
ERT 452

5. Brief History of Vibration
Phenomenon of Vibration
Musical instrument (string)
Use monochord
Pythagoras ( BC)
Observed that if 2 string of different length are subject to the same tension, the shorter one emits a higher note.
Frequency of vibration
ERT 452

6. Brief History of Vibration
(1564 – 1642) Galileo Galilei
- Founder of modern experimental science.
- Started experimenting on simple pendulum.
- Study the behavior of a simple pendulum (observe pendulum movement of a lamp).
- Describing resonance, frequency, length, tension and density of a vibrating stretched string.
(1642 – 1727) Sir Isaac Newton
- Derive the equation of motion of a vibrating body.
ERT 452

7. Brief History of Vibration
(1902 – 1909) Frahm
- Investigate the importance of torsional vibration study in the design of the propeller shafts of steamships.
- Propose the dynamic vibration absorber, which involves the addition of a secondary spring-mass system to eliminate the vibration of main system.
ERT 452

8. Importance of the Study of Vibration
WHY???
Vibrations can lead to excessive deflections and failure on the machines and structures.
To reduce vibration through proper design of machines and their mountings.
To utilize profitably in several consumer and industrial applications.
To improve the efficiency of certain machining, casting, forging & welding processes.
To stimulate earthquakes for geological research and conduct studies in design of nuclear reactors.
ERT 452

9. Importance of the Study of Vibration
EXAMPLE OF PROBLEMS
Vibrational problems of prime movers due to inherent unbalance in the engine.
Wheel of some locomotive rise more than centimeter off the track – high speeds – due to imbalance.
Turbines – vibration cause spectacular mechanical failure.
ERT 452

10. Importance of the Study of Vibration
DISADVANTAGES
Cause rapid wear.
Create excessive noise.
Leads to poor surface finish (eg: in metal cutting process, vibration cause chatter).
Resonance – natural frequency of vibration of a machine/structure coincide with the frequency of the external excitation (eg: Tacoma Narrow Bridge – 1948)
ERT 452

11. Applications
ERT 452

12. Basic Concepts of vibration
ERT 452

13. Basic Concepts of Vibration
Vibration = any motion that repeats itself after an interval of time.
Vibratory System consists of:
1) spring or elasticity
2) mass or inertia
3) damper
Involves transfer of potential energy to kinetic energy and vice versa.
ERT 452

14. Basic Concepts of Vibration
Degree of Freedom (d.o.f.) = min. no. of independent coordinates required to determine completely the positions of all parts of a system at any instant of time
Examples of single degree-of-freedom systems:
ERT 452

15. Basic Concepts of Vibration
Examples of single degree-of-freedom systems:
ERT 452

16. Basic Concepts of Vibration
Examples of Two degree-of-freedom systems:
ERT 452

17. Basic Concepts of Vibration
Examples of Three degree of freedom systems:
ERT 452

18. Basic Concepts of Vibration
Example of Infinite number of degrees of freedom system:
Infinite number of degrees of freedom system are termed continuous or distributed systems.
Finite number of degrees of freedom are termed discrete or lumped parameter systems.
More accurate results obtained by increasing number of degrees of freedom.
ERT 452

19. Classification of vibration
ERT 452

20. Classification of Vibration
Free Vibration: A system is left to vibrate on its own after an initial disturbance and no external force acts on the system. E.g. simple pendulum
Forced Vibration: A system that is subjected to a repeating external force. E.g. oscillation arises from diesel engines
Resonance occurs when the frequency of the external force coincides with one of the natural frequencies of the system

21. Classification of Vibration
Undamped Vibration: When no energy is lost or dissipated in friction or other resistance during oscillations
Damped Vibration: When any energy is lost or dissipated in friction or other resistance during oscillations
Linear Vibration: When all basic components of a vibratory system, i.e. the spring, the mass and the damper behave linearly

22. Classification of Vibration
Nonlinear Vibration: If any of the components behave nonlinearly
Deterministic Vibration: If the value or magnitude of the excitation (force or motion) acting on a vibratory system is known at any given time
Nondeterministic or random Vibration: When the value of the excitation at a given time cannot be predicted

23. Classification of Vibration
Examples of deterministic and random excitation:

24. Vibration analysis procedure
ERT 452

25. Vibration Analysis Procedure
Step 1: Mathematical Modeling
Step 2: Derivation of Governing Equations
Step 3: Solution of the Governing Equations
Step 4: Interpretation of the Results
Derive system/component
Free body diagram
(FBD)
Find the response
(solve problem method)
Response (result):
Displacement, velocities & acceleration

26. Vibration Analysis Procedure
Example of the modeling of a forging hammer:

27. Example 1.1 Mathematical Model of a Motorcycle
Figure below shows a motorcycle with a rider. Develop a sequence of three mathematical models of the system for investigating vibration in the vertical direction. Consider the elasticity of the tires, elasticity and damping of the struts (in the vertical direction), masses of the wheels, and elasticity, damping, and mass of the rider.

28. Example Solution
We start with the simplest model and refine it gradually. When the equivalent values of the mass, stiffness, and damping of the system are used, we obtain a single-degree of freedom model of the motorcycle with a rider as indicated in Fig.(b). In this model, the equivalent stiffness (keq) includes the stiffness of the tires, struts, and rider. The equivalent damping constant (ceq) includes the damping of the struts and the rider. The equivalent mass includes the mass of the wheels, vehicle body and the rider.

29. Example Solution

30. Example Solution
This model can be refined by representing the masses of wheels, elasticity of tires, and elasticity and damping of the struts separately, as shown in Fig.(c). In this model, the mass of the vehicle body (mv) and the mass of the rider (mr) are shown as a single mass, mv + mr. When the elasticity (as spring constant kr) and damping (as damping constant cr) of the rider are considered, the refined model shown in Fig.(d) can be obtained.

31. Example Solution

32. Example Solution
Note that the models shown in Figs.(b) to (d) are not unique. For example, by combining the spring constants of both tires, the masses of both wheels, and the spring and damping constants of both struts as single quantities, the model shown in Fig.(e) can be obtained instead of Fig.(c).

33. Spring elements
ERT 452

34. Spring force is given by:
Spring Elements
Linear spring is a type of mechanical link that is generally assumed to have negligible mass and damping.
Spring force is given by:
F = spring force, k = spring stiffness or spring constant, and x = deformation (displacement of one end with respect to the other)

35. Spring Elements
Work done (U) in deforming a spring or the strain (potential) energy is given by:
When an incremental force ΔF is added to F:

37. Static deflection of a beam at the free end is given by:
Spring Elements
Static deflection of a beam at the free end is given by:
Spring Constant is given by:
W = mg is the weight of the mass m, E = Young’s Modulus, and I = moment of inertia of cross-section of beam

38. Spring Elements
Combination of Springs:
1) Springs in parallel – if we have n spring constants k1, k2, …, kn in parallel, then the equivalent spring constant keq is:

39. Spring Elements
Combination of Springs:
2) Springs in series – if we have n spring constants k1, k2, …, kn in series, then the equivalent spring constant keq is:

40. Example 1.3 Torsional Spring Constant of a Propeller Shaft
Determine the torsional spring constant of the speed propeller shaft shown in Fig

41. Example 1.3 Solution
We need to consider the segments 12 and 23 of the shaft as springs in combination. From Fig. 1.25, the torque induced at any cross section of the shaft (such as AA or BB) can be seen to be equal to the torque applied at the propeller, T. Hence, the elasticities (springs) corresponding to the two segments 12 and 23 are to be considered as series springs. The spring constants of segments 12 and 23 of the shaft (kt12 and kt23) are given by:

42. Example 1.3 Solution

43. Example 1.3 Solution
Since the springs are in series, Eq. (1.16) gives

44. Example 1.5 Equivalent k of a Crane
The boom AB of crane is a uniform steel bar of length 10 m and x-section area of 2,500 mm2. A weight W is suspended while the crane is stationary. Steel cable CDEBF has x-sectional area of 100 mm2. Neglect effect of cable CDEB, find equivalent spring constant of system in the vertical direction.

45. Example 1.5 Solution
A vertical displacement x of pt B will cause the spring k2 (boom) to deform by x2 = x cos 45º and the spring k1 (cable) to deform by an amount x1 = x cos (90º – θ). Length of cable FB, l1 is as shown.

46. Example 1.5 Solution
The angle θ satisfies the relation:
The total potential energy (U):

47. Example 1.5 Solution
Potential Energy of the equivalent spring is:
By setting U = Ueq, hence:

48. Mass or inertia elements

49. Mass or Inertia Elements
Using mathematical model to represent the actual vibrating system
E.g. In figure below, the mass and damping of the beam can be disregarded; the system can thus be modeled as a spring-mass system as shown.

50. Mass or Inertia Elements
Combination of Masses
E.g. Assume that the mass of the frame is negligible compared to the masses of the floors. The masses of various floor levels represent the mass elements, and the elasticities of the vertical members denote the spring elements.

51. Mass or Inertia Elements
Case 1: Translational Masses Connected by a Rigid Bar
Velocities of masses can be expressed as:

52. Mass or Inertia Elements
and,
By equating the kinetic energy of the system:

53. Mass or Inertia Elements
Case 2: Translational and Rotational Masses Coupled Together
meq = single equivalent translational mass = translational velocity = rotational velocity J0 = mass moment of inertia Jeq = single equivalent rotational mass

54. Mass or Inertia Elements
Case 2: Translational and Rotational Masses Coupled Together
1. Equivalent translational mass:
Kinetic energy of the two masses is given by:
Kinetic energy of the equivalent mass is given by:

55. Mass or Inertia Elements
Case 2: Translational and Rotational Masses Coupled Together
2. Equivalent rotational mass:
Here, and , equating Teq and T gives
Since and , equating Teq & T gives

56. Example 1.7 Cam-Follower Mechanism
A cam-follower mechanism is used to convert the rotary motion of a shaft into the oscillating or reciprocating motion of a valve.
The follower system consists of a pushrod of mass mp, a rocker arm of mass mr, and mass moment of inertia Jr about its C.G., a valve of mass mv, and a valve spring of negligible mass.
Find the equivalent mass (meq) of this cam-follower system by assuming the location of meq as (i) pt A and (ii) pt C.

57. Example 1.7 Cam-Follower Mechanism
ERT 452

58. The kinetic energy of the system (T) is:
Example 1.7 Solution
The kinetic energy of the system (T) is:
If meq denotes equivalent mass placed at pt A, with
the kinetic energy equivalent mass system Teq is:

59. By equating T and Teq, and note that
Example 1.7 Solution
By equating T and Teq, and note that
Similarly, if equivalent mass is located at point C, hence,

60. Example 1.7 Solution
Equating (E.4) and (E.1) gives

61. Damping elements
ERT 452

62. Damping Elements
Viscous Damping: Damping force is proportional to the velocity of the vibrating body in a fluid medium such as air, water, gas, and oil.
Coulomb or Dry Friction Damping: Damping force is constant in magnitude but opposite in direction to that of the motion of the vibrating body between dry surfaces.
Material or Solid or Hysteretic Damping: Energy is absorbed or dissipated by material during deformation due to friction between internal planes.

63. Hysteresis loop for elastic materials:
Damping Elements
Hysteresis loop for elastic materials:

64. Construction of Viscous Dampers
Damping Elements
Construction of Viscous Dampers
Velocity of intermediate fluid layers
are assumed to vary linearly
Fixed plane
Plate be moved with a velocity v in its own plane
ERT 452

65. where du/dy = v/h is the velocity gradient.
Damping Elements
Shear Stress ( ) developed in the fluid layer at a distance y from the fixed plate is:
where du/dy = v/h is the velocity gradient.
Shear or Resisting Force (F) developed at the bottom surface of the moving plate is:
where A is the surface area of the moving plate and is the damping constant.

66. Damping Elements
If a damper is nonlinear, a linearization process is used about the operating velocity (v*) and the equivalent damping constant is:

67. Example 1.10 Equivalent Spring and Damping Constants of a Machine Tool Support
A precision milling machine is supported on four shock mounts, as shown in Fig. 1.37(a). The elasticity and damping of each shock mount can be modeled as a spring and a viscous damper, as shown in Fig. 1.37(b). Find the equivalent spring constant, keq, and the equivalent damping constant, ceq, of the machine tool support in terms of the spring constants (ki) and damping constants (ci) of the mounts.

68. Example 1.10 Equivalent Spring and Damping Constants of a Machine Tool Support

69. Example Solution
The free-body diagrams of the four springs and four dampers are shown in Fig. 1.37(c). Assuming that the center of mass, G, is located symmetrically with respect to the four springs and dampers, we notice that all the springs will be subjected to the same displacement, , and all the dampers will be subject to the same relative velocity , where and denote the displacement and velocity, respectively, of the center of mass, G. Hence the forces acting on the springs (Fsi) and the dampers (Fdi) can be expressed as

70. Example Solution

71. Example Solution
Let the total forces acting on all the springs and all the dampers be Fs and Fd, respectively (see Fig. 1.37d). The force equilibrium equations can thus be expressed as

72. Example Solution
where Fs + Fd = W, with W denoting the total vertical force (including the inertia force) acting on the milling machine. From Fig. 1.37(d), we have
Equation (E.2) along with Eqs. (E.1) and (E.3), yield
Parallel

73. Example 1.10 Solution where ki = k and ci = c for i = 1, 2, 3, 4.
Note: If the center of mass, G, is not located symmetrically with respect to the four springs and dampers, the ith spring experiences a displacement of and the ith damper experiences a velocity of where and can be related to the displacement and velocity of the center of mass of the milling machine, G. In such a case, Eqs. (E.1) and (E.4) need to be modified suitably.

74. Harmonic motion
ERT 452

75. Periodic Motion: motion repeated after equal intervals of time
Harmonic Motion
Periodic Motion: motion repeated after equal intervals of time
Harmonic Motion: simplest type of periodic motion
Displacement (x):
Velocity:
Acceleration:
(On horizontal axis)

76. Harmonic Motion Scotch yoke mechanism:
The similarity between cyclic (harmonic) and sinusoidal motion.

77. Complex number representation of harmonic motion:
where i = √(–1) and a and b denote the real and imaginary x and y components of X, respectively.

78. Also, Eqn. (1.36) can be expressed as
Harmonic Motion
Also, Eqn. (1.36) can be expressed as
Thus,

79. Operations on Harmonic Functions:
Harmonic Motion
Operations on Harmonic Functions:
Rotating Vector,
Where Re denotes the real part.

80. Displacement, velocity, and accelerations as rotating vectors
Harmonic Motion
Displacement, velocity, and accelerations as rotating vectors
Vectorial addition of harmonic functions

81. Example 1.11 Addition of Harmonic Motions
Find the sum of the two harmonic motions
Solution:
Method 1: By using trigonometric relations: Since the circular frequency is the same for both x1(t) and x2(t), we express the sum as

82. Example 1.11 Solution That is, That is,
By equating the corresponding coefficients of cosωt and sinωt on both sides, we obtain

83. Example 1.11 Solution
and
Method 2: By using vectors: For an arbitrary value of ωt, the harmonic motions x1(t) and x2(t) can be denoted graphically as shown in Fig By adding them vectorially, the resultant vector x(t) can be found to be

84. Example 1.11 Solution
Method 3: By using complex number representation: the two harmonic motions can be denoted in terms of complex numbers:
The sum of x1(t) and x2(t) can be expressed as
where A and α can be determined using Eqs. (1.47) and (1.48) as A = and α = º

85. Definitions of Terminology:
Harmonic Motion
Definitions of Terminology:
Amplitude (A) is the maximum displacement of a vibrating body from its equilibrium position
Period of oscillation (T) is time taken to complete one cycle of motion
Frequency of oscillation (f) is the no. of cycles per unit time

86. Definitions of Terminology:
Harmonic Motion
Definitions of Terminology:
Natural frequency is the frequency which a system oscillates without external forces
Phase angle () is the angular difference between two synchronous harmonic motions

87. Definitions of Terminology:
Harmonic Motion
Definitions of Terminology:
Beats are formed when two harmonic motions, with frequencies close to one another, are added

88. Definitions of Terminology:
Harmonic Motion
Definitions of Terminology:
Decibel is originally defined as a ratio of electric powers. It is now often used as a notation of various quantities such as displacement, velocity, acceleration, pressure, and power
where P0 is some reference value of power and X0 is specified reference voltage.

89. Harmonic analysis
ERT 452

90. Harmonic Analysis
A periodic function:

91. Harmonic Analysis
Fourier Series Expansion: If x(t) is a periodic function with period , its Fourier Series representation is given by

92. Harmonic Analysis
Gibbs Phenomenon: An anomalous behavior observed from a periodic function that is being represented by Fourier series.
As n increases, the approximation can be seen to improve everywhere except in the vicinity of the discontinuity, P. The error in amplitude remains at approximately 9 percent, even when

93. Harmonic Analysis
Complex Fourier Series: The Fourier series can also be represented in terms of complex numbers.
and
Also,

94. Harmonic Analysis Frequency Spectrum:
Harmonics plotted as vertical lines on a diagram of amplitude (an and bn or dn and Φn) versus frequency (nω).

95. Harmonic Analysis
Representation of a function in time and frequency domain:

96. Even and odd functions:
Harmonic Analysis
Even and odd functions:
Even function & its Fourier series expansion
Odd function & its Fourier series expansion

97. Half-Range Expansions:
Harmonic Analysis
Half-Range Expansions:
The function is extended to include the interval as shown in the figure. The Fourier series expansions of x1(t) and x2(t) are known as half-range expansions.

98. Harmonic Analysis
Numerical Computation of Coefficients. If x(t) is not in a simple form, experimental determination of the amplitude of vibration and numerical integration procedure like the trapezoidal or Simpson’s rule is used to determine the coefficients an and bn.

99. Example 1.12 Fourier Series Expansion
Determine the Fourier series expansion of the motion of the valve in the cam-follower system shown in the Figure.

100. Example 1.12 Solution
If y(t) denotes the vertical motion of the pushrod, the motion of the valve, x(t), can be determined from the relation: or
where
and the period is given by

101. Example 1.12 Solution By defining x(t) can be expressed as
Equation (E.3) is shown in the Figure. To compute the Fourier coefficients an and bn, we use Eqs. (1.71) to (1.73):

102. Example 1.12 Solution

103. Example 1.12 Solution
Therefore the Fourier series expansion of x(t) is
The first three terms of the series are shown plotted in the figure. It can be seen that the approximation reaches the sawtooth shape even with a small number of terms.

104. ERT 452