1. Distribution Statement C: Authorized for Government Agencies and their Contractors Only

2. SSP T&ME LCS Program Overview
Michal Dusendang
(812)

3. Topics
SSP TME LCS Organization
SSBN
SSGN
Key Program Instructions
Key Responsibilities
SSP Technical Branches
SSP TME Requirements Process
NAVSEA Requirements Process

4. SSP LCS Organization INTERFACE ROLE SP201 J. SCHAEFER SP2016 M. RIVERA
B. MORRISON
NAVY TAMS
EXECUTIVE BOARD
SP20163
E. ZACHARIA
TME LCS
SP206
P. VOTH
LOGISTICS
SP502
A. HUNT
STRATSYS SSGL
UK CAL LAB
NAVSEA 07T112
F. COLEMAN
NSWC CORONA, MSD
(CTM)
R. FIGURRES
UII
(CDM)
O. ROBINSON
NSWC CRANE
(CSM)
R. ALLEN
SWFLANT/PAC
(TSBs)
J. LANGE /
S. SCHAFER
NSWC CORONA (QAM)
P. THORNBERRY

5. SSBN Fourteen Ohio-Class SSBNs Notional Schedule: Calibration Support:
Eight home ported in Silverdale, WA
Six home ported in Kings Bay, GA
Notional Schedule:
21 day maintenance period at home port (Silverdale, WA or Kings Bay, GA), 90 Day deployment.
Two Crews (Blue/Gold)
Calibration Support:
Calibration exchanges of portable T&ME conducted during 21 Day maintenance period – 100% portable T&ME calibrated at all times
SWFPAC/SWFLANT Navy Calibration Laboratories support/coordinate installed and installed removable “I” Level T&ME calibration support.

6. SSGN First Four Ohio-Class SSBNs converted to SSGN Notional Schedule:
USS Ohio, USS Michigan, USS Florida, USS Georgia
Notional Schedule:
3-Month Major Maintenance Period at home port (Bremerton, WA or Kings Bay, GA), 15 month deployment, including 3 forward deployed voyage repair periods (VRP).
Calibration Support:
Two calibration exchanges of portable T&ME conducted during MMP (upon return from deployment, and just prior to departure)
Calibration exchange of portable T&ME conducted at each VRP to lessen impact on forward labs.
Short interval installed instruments supported by VR site laboratories
USS Frank Cable (AS-40) – Guam
NAVAIR Calibration Laboratory – Diego Garcia

7. Key Program Instructions
OPNAVINST A (TMDE, ATS, METCAL)
SSPINST C (T&ME LCS Instruction)
OPNAVINST F (TRIDENT Logistics Support)
OD63913 (METPRO)
OD55373A (T&ME LCS Procedures)
OD55551 (SSBN Substitution Guide)
OD64498 (SSGN Substitution Guide)
OD65701 (Calibration Support Procedures for SSGN Forward Deployment)

8. Key Responsibilities for LCS
SSPINST C (T&ME LCS Instruction)
Paragraph 3.a T&ME covered by this instruction…
(1) All SWS, AWS and non-SWS/AWS GPTE, SPTE, GPS and SPS onboard SSBN/SSGN
Paragraph 7 Responsibilities…
f. NAVSEA and SPAWAR shall:
Submit data sheets
Outfit and replace non-SWS T&ME (excluding exchange pool)
Provide support for new requirements (procedures, intervals, equipment)
Provide maintenance documentation to NSWC Crane
Provide authorized substitute information for OD55551
Ensure that NAVSEA resources (e.g., provision of authorized onboard FCA portable calibrators, audit of FCAs, evaluation and certification of FCAs, provision of “O” level calibration procedures)….and notify SSP when changes are planned.

9. SSP Technical Branches
INSTRUMENTATION SUBSYSTEM
INTERSTATE ELECTRONICS CORP
NAVIGATION
SUBSYSTEM N
FIRE CONTROL
SUBSYSTEM
LMNE&SS/BOEING E
GENERAL DYNAMICS
ADVANCED INFORMATION
SYSTEMS W
NAVSEA/SP21 S
SP22
SP28
LAUNCHER
SUBSYSTEM
NORTHROP
GRUMMAN
MARINE SYSTEMS
SUBMARINE SSBN/SSGN
GENERAL DYNAMICS
ELECTRIC BOAT CORP.
REENTRY
SUBSYSTEM
LOCKHEED MARTIN
SPACE SYSTEMS COMPANY
59 SSBN SSP T&ME Requirements = ~ 104 pieces equipment
251 SSBN NAVSEA T&ME Requirements = ~ 708 pieces equipment
SP23
SP27
GUIDANCE
SUBSYSTEM
TRIDENT MISSILE
LOCKHEED MARTIN
SPACE SYSTEMS COMPANY
CHARLES
STARK DRAPER
LABORATORIES, et al

10. SSP Requirements Process
Originator (generally contractor) initiates T&ME Requirement (Data Sheet) via web site

11. SSP Requirements Process
Data Sheet Identifies:
Originator and Approving Official (SSP or NAVSEA Cog)
New, Revised or Cancelled Requirement
SPTE or GPTE
Specific Model, Accessories, Authorized Substitutes chosen from OD Selection List
Procurement Required and by who
Calibration Support (Completed by MSD)
Repair Support
Allocation (SSBN, Work Center, Qty, Prime System)
Procedural Documents for Requirement (MRC, SMP, Tech Manual, RPM, etc.)

12. SSP Requirements Process

13. SSP Requirements Process
Electronic Data Sheet Routing Process Flow
Originator Creates
Designated Government Rep Approves
NSWC Crane Review
Ensure proper TME selection and non-proliferation
Update allowance documentation, initiate procurement, update OD55551 (SSBN Substitution Guide)
NSWC Corona Review
Determine calibration support level, update METRL, identify ICP

14. SSP Requirements Process

15. NAVSEA Requirements Process
Upload
PMS FR
Identify
MRCs added,
deleted
or changed
Identify T&ME
impact
Run
comparison
routine
Cancel Requirement and
Remove T&ME if required
New
Requirement
Link Requirement
to Data Sheet No
Yes
Generate “Matrix” of
Data Sheet requirements
Proliferation of
T&ME
Obviously the data sheet process is in an ideal world, that does not exist. To ensure changing requirements are captured, NSWC Crane reviews both SSP and NAVSEA maintenance documentation for portable T&ME impacts. The intent of the process is to ensure the sailor has the equipment to perform the procedure, remove equipment not required and ensure calibration support in place.
Initiate Data Sheet No
Yes
Use Equipment Onboard

16. NAVSEA Requirements Data

17. T&ME Matrix

18. NAVSEA 08 Requirements Process
BPMI generate new requirements (Data Sheets)
NAVSEA 08 approve requirements
NAVSEA 08 determine revised or cancelled requirements
BPMI procure initial outfitting and exchange pool
NSWC Crane push requirements to exchange pool/boats (need schedule)
NSWC Crane update GPTE Addendum with NAVSEA 08 SCAT requirements
NAVSEA 08 remove SCAT requirements from QCOSAL?
NSWC Crane update “Matrix”

19. Questions?