Presentation is loading. Please wait.

Presentation is loading. Please wait.

P13651: FINAL DESIGN. Contents Revised Design Subsystem design Power requirements BOM/Budget.

Published byAnne McCarthy Modified over 9 years ago

Similar presentations

Presentation on theme: "P13651: FINAL DESIGN. Contents Revised Design Subsystem design Power requirements BOM/Budget."— Presentation transcript:

1 P13651: FINAL DESIGN

2 Contents Revised Design Subsystem design Power requirements BOM/Budget

3 Hold Wax: Hopper Designed to hold an entire bag of wax flakes Reduces operator work during operation Hopper held within base with springs to reduce affects of vibrations from vibrator For drawings see attached

4 Transport Wax: Chute Goal: Transport 2 gallons of wax at a time into the tank Wax flow controlled by a door operator by a linear actuator Ideal chute angle to transport wax flakes: 45° Vibrator is attached to the backside of chute to improve transfer Super-Quiet Low-Impact Electric Vibrator Nonadjustable Force, 115 VAC, 1.4 Amps, 25 lbs Force http://www.mcmaster.com/#catalog/119/517/=lsgnla

5 Melt Wax: Melting Tank Goal: Melt 2 gallon batch of wax within 10 minutes Aluminum tank structure heaters around exterior wall of tank is sole provider of heat to melt the wax Aluminum shaft and 2 stirrers induce flow and increase melt rate Insulation surrounding tank prevent heat loss to surroundings

6 Heat Requirements Energy Required to Melt 50 lb of Wax 50 lb/hr100 lb/hr KC 40889831967 Cerita 28-811482296 Solucore 114917113422 Testing Melter Efficiency39% Melted varying quantities of three sample wax in a home wax melting unit Determined melter efficiency by comparing results from testing to known material, paraffin Used data to determine amount of energy required to achieve customer requirement of 50 lb/hour

7 Sample Calculations Raw DataAnalyzed DataPower Required TrialAmt (lbs) Melt Time (min) Time (s)Weight (kg) Melt Rate (kg/s) Heat of Fusion (J/kg) 50 lb/hr100 lb/hr 10.616.589950.27220.00027213E+313412682 20.611.827090.27220.00038152E+39561911 30.614.988990.27220.00030192E+312122423 40.616.8310100.27220.00027216E+313612723 5126.1715700.45360.00029202E+312702539 6120.6312380.45360.00037159E+310012002 7120.3812230.45360.00037157E+39891978 8124.3714620.45360.00031188E+311822365 91.435.0221010.63500.00030193E+312142427 101.427.5016500.63500.00038151E+39531906 Average182E+311482296 Power (W)58.23 Required Melt Rate (lb/hr) 50 Required Melt Rate (kg/s) 0.0063 Required Melt Rate (lb/hr) 100 Required Melt Rate (kg/s) 0.0126

8 System Heaters System will require 4 heaters to provide enough energy and cover the tank Heaters will come up to 2.25in down from the top of the tank Heat density of 100W/in 2 Watlow Band/Barrel Heaters http:/www.watlow.com/downloads/en/catalogs/band-barrel.pdf/

9 Melted Wax Transport Goal: Achieve 50 lb/hour flowrate Flow rate out of tank controlled by a door operated by a linear actuator Outlet through current baseplate into reservoir

10 BOM: Metal Metals Item #QuantityDescriptionPartVendorCode/Part NumberLead TimeUnit PriceTotal Price 131 Cold Roll Mild Steel Sheet A366/1008, 20"x20" 16 Gauge Chute wall of Hopper online metals -- $ 24.00 141 Cold Roll Mild Steel Sheet A366/1008, 10"x60" 16 Gauge Hopper bottom wall (3 sides) online metals -- $ 24.00 152 Cold Roll Mild Steel Sheet A366/1008, 12"x40" 16 Gauge Hopper box online metals -- $ 19.20 $ 38.40 164 Cold Roll Mild Steel Sheet A366/1008, 12"x24" 16 Gauge Heater box walls online metals -- $ 9.31 $ 37.24 171 Cold Roll Mild Steel Sheet A366/1008, 12"x12" 16 Gauge Heater box top online metals -- $ 4.82 181 Cold Finish Mild Steel Rectangle 1018, 6"x30"x1/8" Hopper support (Angled) online metals -- $ 30.30 191 Cold Finish Mild Steel Rectangle 1018, 1/4"x2"x36" Hopper support (Horizontal) online metals -- $ 17.20 204 DOM Mild Steel Tube A513 TYPE 5, length 36", OD=3/4", ID=0.53" with wall thickness 0.109 " Support Rods online metals -- $ 10.09 $ 40.36 211 Cold Finish Alloy Sheet Steel 4130 Annealed, 10"x10"x.19" L Brace online metals $ 38.00 221 Extruded Aluminum Round 6061 T6511, length 2-1/4", OD=8" Heater base online metals -- $ 57.89 231 Aluminum 6061-T6 Bare Sheet, 18" x 26", thickness=1/8" Heater tank online metals -- $ 60.84 241 Extruded Aluminum Round 6061 T6511, length 24", dia 3/4" Stir shaft online metals -- $ 4.74 251 Extruded Aluminum Round 6061 T6511, length 24" L, dia 1.5" Stir blades online metals -- $ 18.95 261 Mild Steel BLANCHARD GROUND Plate 1018, 24"x24"x1/2" Base plate online metals -- $ 284.51 Metal Sub-Total $ 681.25

11 BOM: Electrical Electrical Components Item #QuantityDescriptionPartVendorCode/Part NumberLead TimeUnit PriceTotal Price 112Logic Gates Electrical Component DigiKey 4 AND, 2 NOR, 2 OR, 4 Inverter packages 5 Days $ 0.42 $ 5.04 2101% resistors for booster circuit Electrical Component Digikey-3-5 Days $ 0.50 $ 5.00 34MOSFETs for booster circuits Electrical Component Digikey-- $ 0.60 $ 2.40 42120 V Relays Electrical Component DigikeyZ774-ND- $ 2.07 $ 4.14 5120 A breaker Electrical Component Lowes Square D Qo 20A breaker Ready to purchase $ 6.44 6 1 12/2 Wire Electrical Component Lowes50' of 12 AWG 12-2 Ready to purchase $ 33.24 71Light Switch Electrical Component Lowes Single standard 15 A light switch Ready to purchase $ 5.00 81Primary Drive Motor Electrical Component Grainger Dayton motor 1/3 HP GP item #5K917 Purchased $ 130.00 92Linear actuator for valves Electrical Component Firgelli automation -- $ 160.00 $ 320.00 101Signal wire Electrical Component - 20 gauge signal wire of various colors, 10ft On hand $ - 111K-A-Watt Electrical Component --- $ 40.00 124Heater Electrical Component WatlowME7L3AP1 Purchased 2 weeks ago $ 130.00 $ 520.00 Electrical Components Sub-Total $ 1,071.26

12 BOM: Auxilliary Auxiliary Components Item #QuantityDescriptionPartVendorCode/Part NumberLead TimeUnit PriceTotal Price 272 High-Temp Cast Iron Mounted STL Ball Bearing 2-Bolt Flange Mount, for 3/4" Shaft Diameter Bearing McMaster- Carr 6665K332 Weeks $ 112.72 $ 225.44 281 Right-Angle Speed Reducer Shaft Input, 30:1 Ratio, 1.33" Center, Left Output Speed reducer/ Gear box McMaster- Carr 5887K3213 Days $ 357.87 292 Steel Machinable-Bore Sprocket for #25 Chain, 1/4" Pitch, 30 Teeth, 3/8" min Bore Bore sprockets for roller chain McMaster- Carr 6793K19In stock $ 10.35 $ 20.70 301 Standard ANSI Roller Chain #25, Single Strand, 1/4" Pitch,.13" Dia, 4ft length Chain McMaster- Carr 6261K171In stock $ 14.92 311 Very HI-Temp Mineral Wool Insulation Wire Mesh One Side, 1" Thick, 24" X 48" Sheet Insulation McMaster- Carr 9328K21In stock $ 18.79 3210 Reusable SS Harsh-Environment Cable Tie 45" Length, bundle dia 12 1/2" Insulation holder McMaster- Carr 1853T64In stock $ 2.36 $ 23.60 331 Tape Made with Kapton® Polyimide High Temperature, 6" W, 5 Yards,.0025" Thk Electrical Insulator McMaster- Carr 7648A718In stock $ 57.94 341 2 oz., highly conductive two part epoxy to 500°F Thermally Conductive Epoxies OmegaOB-200-2In stock $ 17.00 351 Super-Quiet Low-Impact Electric Vibrator Nonadjustable Force, 115 VAC, 1.4 Amps, 25 lbs Force Hopper vibrator McMaster- Carr 5802K13In stock $ 264.63 368 High Load Plastic Compression Spring 250 in-lbs Energy Cap, 1.11" Overall Diameter Springs McMaster- Carr 9677K12In stock $ 8.14 $ 65.12 Auxiliary Sub-Total $ 1,066.01

13 Manufacturing Costs Manufacturing Cost Item #QuantityDescriptionPartVendorCode/Part NumberLead TimeUnit PriceTotal Price 371CNCTank Base Brinkman Lab -2 weeks $ 500.00 381Water jetBase Plate Brinkman Lab `1 week $ 50.00 391Water jetL-Brace Brinkman Lab `1 week $ 50.00 Manufacturing Sub-Total $ 600.00

14 Budget Breakdown Project Budget $ 5,000.00 Metal Parts $ 681.25 Electrical Parts $ 1,071.26 Auxilliary Parts $ 1,066.01 Machining Costs $ 600.00 Total $ 3,418.52 Remaining in Budget $ 1,581.48

Download ppt "P13651: FINAL DESIGN. Contents Revised Design Subsystem design Power requirements BOM/Budget."

Similar presentations

All Russelectric 4 pole Open Transition ATS’s have a fully rated -break before make- switched neutral, identical in every way to the main power poles and.

All Russelectric 4 pole Open Transition ATS’s have a fully rated -break before make- switched neutral, identical in every way to the main power poles and.
HVAC523 Heat Sources.

HVAC523 Heat Sources.
Basic Electricity.

Basic Electricity.
Quiz – 2014.02.05 An organic liquid enters a 0.834-in. ID horizontal steel tube, 3.5 ft long, at a rate of 5000 lb/hr. You are given that the specific.

Quiz – An organic liquid enters a in. ID horizontal steel tube, 3.5 ft long, at a rate of 5000 lb/hr. You are given that the specific.
P5 Electric Circuits. Question 1 How do you generate a current in a coil of wire?

P5 Electric Circuits. Question 1 How do you generate a current in a coil of wire?
TIGERBOT MECHANICAL DESIGN Kyle Backer (EE), Jeremy Jensen (ME), Matthew DeCapua (EE), Eric Walkama (ME), Mike Thomas (EE), Jonathan Cormier (CE), John.

TIGERBOT MECHANICAL DESIGN Kyle Backer (EE), Jeremy Jensen (ME), Matthew DeCapua (EE), Eric Walkama (ME), Mike Thomas (EE), Jonathan Cormier (CE), John.
UNIT 16: Extrusion and Injection moulding Manufacturing Engineering Unit 16 Copyright © 2012 MDIS. All rights reserved. 1.

UNIT 16: Extrusion and Injection moulding Manufacturing Engineering Unit 16 Copyright © 2012 MDIS. All rights reserved. 1.
Gripper Designs By Pragnay Choksi. INTRODUCTION Hands of robots referred to as Grippers No single design is ideal for all applications.

Gripper Designs By Pragnay Choksi. INTRODUCTION Hands of robots referred to as Grippers No single design is ideal for all applications.
LEarNeR© Kit 1- Core LENR Reactor Description of hardware, fittings and raw metal that can be purchased. Prices, part numbers & vendors, high pricing for.

LEarNeR© Kit 1- Core LENR Reactor Description of hardware, fittings and raw metal that can be purchased. Prices, part numbers & vendors, high pricing for.
Plans for a Machine to Collect Plastic Mulch. The use of plastic mulch is a common practice for strawberry and vegetable growers, but there are two major.

Plans for a Machine to Collect Plastic Mulch. The use of plastic mulch is a common practice for strawberry and vegetable growers, but there are two major.
Engine Removal and Disassembly

Engine Removal and Disassembly
WHAT IS MANUFACTURING? Why do we study manufacturing?

WHAT IS MANUFACTURING? Why do we study manufacturing?
Filter manifold Holding tank Iron- manganese filter Aeration tank Control unit Pre- filter To storage tanks Backwash overflow SO2 vent Bypass Cutoff valve.

Filter manifold Holding tank Iron- manganese filter Aeration tank Control unit Pre- filter To storage tanks Backwash overflow SO2 vent Bypass Cutoff valve.
DAY 4 CHAPTER 3 CONDUCTOR SIZES,TYPES, ETC.. Continuous Load. A load where the maximum current is expected to continue for 3 hours or more. Continuous.

DAY 4 CHAPTER 3 CONDUCTOR SIZES,TYPES, ETC.. Continuous Load. A load where the maximum current is expected to continue for 3 hours or more. Continuous.
Peltier Solar Concentrator By: Michael Forrest Kyle Fifield Evan White.

Peltier Solar Concentrator By: Michael Forrest Kyle Fifield Evan White.
0 Beach Cities Robotics FRC Team 294 Summer Academy Motors and Gears July 20, 2008 Rick Wagner, Mentor, Beach Cities Robotics FIRST Team 294.

0 Beach Cities Robotics FRC Team 294 Summer Academy Motors and Gears July 20, 2008 Rick Wagner, Mentor, Beach Cities Robotics FIRST Team 294.
Development of Laser Fuser Test Bed Project Number: P07501 Justin McMillan.

Development of Laser Fuser Test Bed Project Number: P07501 Justin McMillan.
EET Survey of Electronics

EET Survey of Electronics
Electrical Power Systems

Electrical Power Systems
P13651 – MPI Wax Melter.  Change from design review  System Architecture/subsystems  Feasibility  Test plan  Risk assessment  BOM  MSD II Plan.

P13651 – MPI Wax Melter.  Change from design review  System Architecture/subsystems  Feasibility  Test plan  Risk assessment  BOM  MSD II Plan.

Similar presentations

Ads by Google