Presentation is loading. Please wait.

Presentation is loading. Please wait.

PPE Use Standard (SSP-0011) Y Full Face Shield / Goggles Hood Clothing—Chemical Protection Gloves—Chemical Personal Fall Protection Respirator / Filter.

Similar presentations


Presentation on theme: "PPE Use Standard (SSP-0011) Y Full Face Shield / Goggles Hood Clothing—Chemical Protection Gloves—Chemical Personal Fall Protection Respirator / Filter."— Presentation transcript:

1 PPE Use Standard (SSP-0011) Y Full Face Shield / Goggles Hood Clothing—Chemical Protection Gloves—Chemical Personal Fall Protection Respirator / Filter Mask Supplied Air Job Hazards Y es Job Hazards Y es Access and EgressMoving Parts Activities of OthersNoise Adverse WeatherRail Movement Chemical ExposureSharp Edges ElectricitySlips, Trips, and Falls FatigueStatic Electricity Fire and ExplosionTrip Injuries Ground ContaminationTrapped Pressure Manual HandlingWorking at Height Other: References / Documents  ASTM D36 AreaUnitOperating Procedure #Certified byRevision #DatePage 3LabOPS-LB-PT of 2 Automated Softening Point Measurement Using ISL RB36 EnvironmentalSpecial Instructions Automated Softening Point Measurement Using ISL RB36 1Lightly grease brass pouring plate with silicon grease to prevent sticking. 2Place ring on pouring plate. 3Pour a slight excess of heated sample into ring and allow to cool for 30 minutes. 4Fill beaker to mark with glycerin. 5Remove any excess sample from outer portion of ring with knife or razor and flatten top of sample so that flush with ring. 6Place ring with sample in appropriate hole in ring and ball holder. 7 Referring to picture below, place ball centering guide on top of ring (ensure sits flush on holder oriented such that guide pins not touching ring). 8Place ball in center of ball centering guide. 9Place ring and ball holder in the beaker filled with glycerin. 10Set the temperature probe in place (through center hole on top plate of holder assembly). 11Install the beaker on the heating stand. 12Select the bath type using the L/Q key. (Press button 3 times to get to “G”.) EquipmentMaterials and Reagents  Ring, Brass (Part #V048101)  Ball Centering Guide (Part #Q048006)  Temperature Probe (Part #L00140)  Ball, Steel (Part #V048105)  Ring and Ball Holder (Part #V048100)  Pouring Plate – flat, smooth, brass plate  USP Glycerin  Stir Bar  ISL Beaker (Part #M00413)  Silicon Grease Scope / Objective This procedure covers the determination of softening point within the range of ° F using automated instrumentation. Note: This procedure is only valid at the time of printing. The control version can be found on the Meraux Refinery intranet. Completed Date:Prepared By:Approved By:

2 AreaUnitOperating Procedure #Certified byRevision #DatePage 3LabOPS-LB-PT of 2 Automated Softening Point Measurement Using ISL RB36 Continued 13 Enter a sample number if desired. To enter a sample number: a.Depress the (N) key – a number will display. b.Enter new number (1 – 6 figures) using keypad – display will blink. c.Depress the (ENT) key to validate. 14Start stirrer by depressing “-O-” key. 15Start test by depressing ON key. 16Test will end when ball drop is detected – an audible alarm will sound and display will blink. 17 Press “ALA” key to silence alarm. IMPORTANT: At test end, “ALA” key must be depressed to store data. If “OFF” key is pressed to silence alarm, data will be lost and will not be retrievable. 18Record temperature reading from display screen. 19Clean test components with toluene while still warm. CAUTION: Allow beaker to cool before removing from heating plate. Note: This procedure is only valid at the time of printing. The control version can be found on the Meraux Refinery intranet. Completed Date:Prepared By:Approved By:


Download ppt "PPE Use Standard (SSP-0011) Y Full Face Shield / Goggles Hood Clothing—Chemical Protection Gloves—Chemical Personal Fall Protection Respirator / Filter."

Similar presentations


Ads by Google