Presentation is loading. Please wait.

Presentation is loading. Please wait.

Microfilter (2-way splitter) Phone Jack Phone Cable (RJ11) *Plug the given microfilter into the connector marked at the back of the router. Connect the.

Similar presentations


Presentation on theme: "Microfilter (2-way splitter) Phone Jack Phone Cable (RJ11) *Plug the given microfilter into the connector marked at the back of the router. Connect the."— Presentation transcript:

1 Microfilter (2-way splitter) Phone Jack Phone Cable (RJ11) *Plug the given microfilter into the connector marked at the back of the router. Connect the phone cable RJ-11 from the microfilter label ADSL to the main phone socket & another RJ-11 from Tel to your telephone line jack. *For surfing only, you may connect the phone cable directly to the router without going thru the microfilter. Straight RJ-45 Cable 1. Turn off the computer. 2. Plug the end of the Ethernet cable RJ-45 into any one connector marked at the back of the router. 3. Plug the other end of the Ethernet cable into your computer's RJ-45 jack of the Ethernet card. Turn on the PC. *You may connect to a Hub/Switch to have more than 4 PCs connected. Connect the given Power adaptor to the Jack marked and then switch on the power point. 5V Power Adapter The console port is connected using the RJ–232 serial cable for configuration purposes. Normally you do not need to connect it. User is recommended to use the Web-based management to configure. Please refer to the back page for more information. Line Jack LAN Connectors Console Port Power Connector For Phone Cable (Rj-11), to connect to ADSL Line For Lan Cable (Rj-45), to connect to PCs Network Card For Serial Cable (RS-232), to connect to Serial Port (Normally, no need to connect it) Power LED (In red color) Light ON once detected *ADSL LED (In green color) Light ON when the connection is ON LAN LED X 4 (In green color) Keeps ON, Light blinks during data transfer ADSL TEL Power Point Quick Installation Guide for Hurricane8800P ( For Singapore Users ) ( For Singapore Users ) A. Hardware Installation A. Hardware Installation Straight RJ-45 Cable After connecting up as shown on 1,2 and 3, you should see the following lights on the router *If ADSL LED fail to light UP. CHECK1 : All telephones sharing the same ADSL line are attached with microfilters each CHECK2 : ADSL account is activated and your ADSL line condition (check with your ISP if youre unsure) Laptop RJ-45 Connection Desktop RJ-45 Connection

2 B. Configure Your PCs Specify a static IP for your individual PCs. For Windows 95/98/ME Go To Control Panel >Network>TCP/IP of your LAN card > Properties For Windows 2000/XP Click the Start button and then Control Panel. From there, click the Network and Internet Connections icon. Then click the Network Connections icon *Set IP Address to X (X : 2~254) Set Subnet Mask to Add Gateway to Enable DNS server Host : pc Add Singnet/Pacnet DNS Select TCP/IP of your Lan Card and then click Properties Select Internet Protocol(TCP/IP) and then Click Properties Key in the IP Add, Subnet Mask, Gateway and DNS Server as follow C. Web-Based Configuration Open Internet Explorer/Netscape, type in Default username: admin password: admin The system will remind you to enter the administrator s username and password when restarting or configuring. *Click Router mode under Configuration and choose PPPOA routed. Then click Configure (i) Description: Name of the WAN connection. (e.g. SingNet) (ii) Choose CHAP (iii) User name and Password: The user name and password will be provided by your ISP when applying for ADSL service. ) (iv) The rest of the settings will be in default (v) Click the Configure button Click Security. Choose Enable under Security State and click Change State Click Add Interface under Security Interface Add LAN Interface Name: ppp-0Interface Type:external Click Apply Remember to click on the Add button Select the Local Area Connection icon for the applicable Ethernet adapter and then do a Right Click and select Properties Notes: i) You may have to disable the proxy settings on your internet browser. ii) For IE user, go to Tools> Internet Options>Connections>Choose Never dial a connection>go to LAN Settings>Disable Proxy Server ii) For Netscape user, click Edit>Preferences>Advanced>Proxies>Choose Direct connection to the Internet Click Add Interface under Security Interface again Add WAN Interface Name : eth-0 or ip1 Interface Type : Choose internal Click Apply Click Enable NAT to internal interfaces The configuration of PPPoA Router mode has been done NOTE: Please remember to save the configuration after finishing the settings. Click Save Config and then click the Save button to store your settings *Pls refer to the manual for the configuration of other routing modes. Note : The router is OS Independent. *IP Address for each PC MUST BE Unique. Example PC 1 IP add is , therefore PC 2 IP add should be and so forth.


Download ppt "Microfilter (2-way splitter) Phone Jack Phone Cable (RJ11) *Plug the given microfilter into the connector marked at the back of the router. Connect the."

Similar presentations


Ads by Google