GSM Fundamentals.

GSM Fundamentals

Contents Basic Concepts of Cellular Mobile System
GSM Network Components Terrestrial Interface Service Area and Number Planning Channels on The Air Interface Radio Techniques The Future Development

GSM Development 1989 Standard Protocol for GSM take effect 1991
GSM system began to provide service in Europe(2G) System was named as Global System for Mobile Communication 1992 1994 Provide services for the whole world 1996 Micro Cell Technique is used in GSM system

The Frequency Spectrum
Downlink Uplink EGSM Each cell in the Cellular Network requires a RF carrier. A RF carrier is a pair of radio frequencies. One is used in each direction (including transmitting and receiving) so that information may be passed in both directions simultaneously. The frequency spectrum allocated for cellular system is only a narrow bandwidth. The bandwidth for the GSM system is 25MHz. The transmitting and receiving frequencies in GSM are separated by 45MHz to avoid interference. The frequency bandwidth used for the downlink (from base station to MS) is MHz. The frequency bandwidth for the uplink (from MS to base station) is MHz. The channel bandwidth is 200KHz. Considering the interference to other systems, the very first carrier is not used. Thus, there are only 124 RF carriers in the GSM frequency band. GSM EGSM GSM 880 890 915 925 935 960 MHz Channel Bandwidth: 200KHz Duplex Separation: 45 MHz

Frequency Spectrum in GSM System
The bandwidth for the DCS1800 (GSM1800) system is 75MHz. The transmitting and receiving frequencies in DCS1800 are separated by 95MHz to avoid interference. The frequency bandwidth used for the downlink (from base station to MS) is MHz. The frequency bandwidth for the uplink (from MS to base station) is MHz. The channel bandwidth is 200KHz just the same as GSM. Due to interference to other systems, the very first carrier is still not used. Thus, there are 374 RF carriers in the DCS1800 frequency band. Thus, DCS 1800 has three times the frequency allocation of GSM 900. So you will understand that DCS1800 can meet the requirements of high traffic in the large densely populated area, while GSM 900 can meet the requirements of large coverage. ARFCN: Absolute Radio Frequency Channel Number

Frequency Allocation in Iraq
GSM900 Operator Frequency Bandwidth Channel Number ARFCN UpLink DownLink Zain 11.6 MHz 58 and 0 - 8 Korek 9 - 66 Asiacell GSM1800 7.5 MHz 38 ARFCN: Absolute Radio Frequency Channel Number

Cell Structure Omni Cell Sector Cell
1 120 degree 2 120 degree 120 degree 1 3 The hexagonal regions in this diagram are known as cells and represent the geographic area covered by one RF carrier. Sure it is really like the shape of bee’s cell. Now you will understand that why it is called as cellular system. Cellular system involves dividing a large service area into regions called "cells". Each cell has the equipment to switch, transmit and receive calls from any subscriber located within its' radio coverage area. Cells are conventionally regarded as being hexagonal, but in reality they are irregularly shaped. The cell shape is determined by the nature of the surrounding area such as hills, tall buildings etc. In Omni -Directional Cells, all the cells have their own Cell Site this is known as an Omni cell. When traffic density is very high, cells can be reduced into many smaller size called as “sectoring ". In 120 Degree Sectors, the original cell is divided into three smaller cells. These cells share the same cell site but each has its own allocation of radio carriers.

Cell Structural in Sulymaniyah

What is Frequency Re-Use?
Because frequency resource of mobile system is very limited, The different Subscribers must use the same frequency in different place. Of course, the quality of communication must be ensured.

How can we reuse frequency?
Frequency Re-Use How can we reuse frequency? 2 1 3 4 5 6 7 7(Site)X 1(Cell) Re-use 2 1 3 4 5 6 7 Because the frequency spectrum allocated for cellular system is only a narrow bandwidth, it is very clear that there are not enough frequencies available for every cell to have a different RF carrier. Therefore the frequencies must be reused. It means that the same RF carrier can be used in other several different cells at the same time. By reusing frequencies, many more phone calls may be made. The radio frequencies available are allocated according to a regular pattern. In this way, each carrier used repeatedly throughout the coverage area according to a frequency re-use pattern. This diagram illustrates 4*3 Re- Use Pattern. It means that 4 sites share the same group frequencies and each site has 3 cells. These group frequencies can be reused in another 4 sites. Care must be taken to make the cells which are using the same frequencies far enough apart from one another to prevent interference.

Frequency Re-Use 4(Site)X 3(Cell) Re-use 6 5 1 9 6 10 2 7 3 11 8 4 12

GSM Network Components
OMC M2000 Server PSTN ISDN MS BTS MSC/VLR GMSC BSC MS MS BTS BTS Other PLMN BSC MS SS7 This diagram shows a simplified GSM network. The main components of a GSM System are: BSS, NSS and OMC The Mobile Station (MS) is the only direct part of the network that the subscriber can see. BSS means Base Station Subsystem. BSS is responsible for the system functions related to radio and transmission of the GSM system. BSS includes BSC and BTS. BSC means base station controller. BTS means base transceiver station. NSS means Network Subsystem. NSS is composed of MSC/VLR, HLR/AuC/EIR. NSS is the control and switching part of the whole GSM system. MSC means Mobile Switching Center. HLR means home location register. AuC means authentication center. EIR means equipment identification register. MSC provides the interface between GSM network and the Public Switched Telephone Network (PSTN). OMC means operation and maintenance center. It is used to configure and maintain the network from a central location. OMC is connected to BSS and NSS through LAN or WAN. BTS MS SMS system HLR/AUC MS BSS NSS

MS=ME+SIM Mobile Station—MS
International Mobile Equipment Identity (IMEI) – Mobile Equipment The Mobile Station consists of two parts, the Mobile Equipment (ME) and an electronic “smart card” called a Subscriber identity module (SIM card). The Mobile Equipment is the hardware used by the subscriber to access the network. This may be a telephone, fax machine etc. The hardware has an identity number which is unique for that particular device and permanently stored in it. This enables stolen mobile equipment to be detected by GSM system. This identity number is called an International Mobile Equipment Identity (IMEI). The SIM is a card which plug into the Mobile Equipment. This card identifies the mobile subscriber and also provides other information regarding the service. The subscriber is identified by an identity number called the International Mobile Subscriber Identity (IMSI). Mobile Equipment may be purchased from any store but the SIM card must be obtained from the GSM network operator. When SIM card is not inserted into the mobile equipment, only the emergency calls can be made. International Mobile Subscriber Identity (IMSI) – Subscriber Identity Module

Subscriber Identity Module – SIM
International Mobile Subscriber Identity (IMSI) Temporary Mobile Subscriber Identity (TMSI) Location Area Identity (LAI) Subscriber Authentication Key (Ki) The SIM card as mentioned previously is a "smart card" which plugs into the mobile equipment and contains information about the mobile subscriber. The SIM card contains the following information: International Mobile Subscriber Identity (IMSI) - This number identifies the mobile subscriber. It is only transmitted over the air interface during initialization. Temporary Mobile Subscriber Identity (TMSI) - This number identifies the subscriber, it is periodically changed by the system in order to protect the subscriber from being identified by someone monitoring the radio interface. Location Area Identity (LAI) identifies the current location of the subscriber. Subscriber Authentication Key (Ki) - This is used to authenticate the SIM card. Mobile Station International ISDN Number (MSISDN) - This is the telephone number of the mobile. It is comprised of a country code, a national code and a subscriber number. Most of the data contained within the SIM is permanent (such as Ki and IMSI). Some of the parameters (such as LAI) will be continuously updated to reflect the current location of the subscriber. The SIM card has high security and provides protection for the subscriber's information to be difficult to duplicate. The SIM can be also protected by use of Personal Identity Number (PIN) password. PIN is similar to credit card password and it is used to prevent unauthorized use of the card. The SIM card also executes the Authentication Algorithm in which Ki is used. * PIN and PUK are used to SIM security

Base Station Subsystem (BSS)
Base Station Controller (BSC) - Base Transceiver Station (BTS) - Transcoder and Sub multiplexer (TCSM) or Transcoder and Rate Adaptation Unit (TRAU) BTS The BSS provides the connection between the mobile equipment and the Mobile Switching Center. The BSS consists of two major hardware components: The BSC provides the control for the BSS and communicates directly with the MSC. The BSC may control one or more BTS. The BTS comprises of a combination of RF equipment that provides the air interface for a particular cell. This is the part of the GSM network that communicates with the mobile station. The antenna is included as part of the BTS. The Transcoder is used to compress the signals so that they can be more efficiently sent over the terrestrial interfaces. In fact it will convert data between 64kbps and 16kbps. Sub-Multiplexer is used to combine the data in order to save the transmission cost between MSC and BTS. Although the Transcoder is considered to be part of the BSS, but it is very often located closer to the MSC in order to optimize the transmission between MSC and BSC. BSC TCSM MSC/VLR MS BTS BSS MS

Base Transceiver Station (BTS)
BTS (Base Transceiver Station): Transmit & Receive signal with MS then transfer to Base Station Controller (BSC) Signal Process: Speech Coding, Channel Coding, Interleaving, Ciphering, Modulation However, one BTS has coverage area limited. Size of coverage area depend on population of subscriber. A unit of coverage area is called “Cell” BTS BTS BTS BTS BSC MS MS

Base Station Controller (BSC)
Store cell information and parameter: eg. Cell ID, BSIC, Cell frequency (ARFCN), Output power Control BTS to process: eg. Call set up, Handover Process, Frequency Hopping, Power Control. Receive BTS alarm and send BTS & BSC alarm to OMC Measurement traffic statistic Remote BTS O&M via BSC BSC BTS BTS BSC MS MS

Transcoder and Sub-Multiplexer
It is known that the 64Kbps Pulse Code Modulation (PCM) circuits are adopted in PSTN. So if 64kbps from the MSC transmitted on the air interface without modification, it would occupy an excessive amount of radio bandwidth. This would use the available radio spectrum inefficiently. Then the Transcoder is required to convert the speech or data output from the MSC into the data rate specified by GSM standard. For example, 64kbps/PCM is converted to 13kbps speech or 3.6/6/12kbps data over the interface between BSS and MS. The required bandwidth is therefore reduced. Transcoder may be located with the MSC or BSC. If it is located at the MSC, the 13kbps channels are transmitted to the BSS by inserting additional synchronization data to 16kbps and then combining four of them into each 64kbps terrestrial circuit. Thus each 30 channel 2Mbps PCM link can carry 120 GSM- specified voice channels. It obviously costs savings for the system operator. Therefore, Transcoder is commonly arranged to be located with the MSC side and it will reduce the number of 2 Mbps link required.

Network Switching System (NSS)
MSC/VLR GMSC EC SS7 PSTN ISDN Other PLMN BSS IWF EIR The Network Switching System includes the main switching functions of the GSM Network. It also contains the databases required for subscriber data and mobility Management. Its main function is to manage communications between the GSM Network and other networks. The components of the Network Switching System are listed below: Mobile Switching Center - MSC Home Location Register - HLR Visitor Location Register - VLR Equipment Identity Register - EIR Authentication Center - AUC Inter-Working Function -IWF Echo Canceller -EC In addition to mobile switching center, NSS has Location Register network entities. These entities are the Home Location Register (HLR), Visitor Location Register (VLR), Equipment Identity Register (EIR). Normally, HLR, AuC and EIR are located in the same physical entity, and MSC/VLR can also be co-located in one physical entity. All the database registers are used to manage subscriber data and keep track of a mobile subscriber’s location as it roams around the network. Functionally, the Inter working Function and the Echo Canceller may be considered as parts of the MSC since their activities are linked with the switch. Echo Canceller is used between PSTN and MSC. Inter working Function is used between MSC and other network. HLR/AUC MSC = Mobile Switching Center GMSC = Gateway MSC HLR = Home Location Register IWF = Inter-Working Function VLR = Visitor Location Register AuC = Authentication Center EIR = Equipment Identity Register EC = Echo Canceller

Mobile Service Switching Center – MSC
Call Processing Operations and Maintenance Support Inter-network & Inter-working Billing The main function of MSC is for call- switching in GSM system. Its overall purpose is the same as that of any telephone exchanger. The MSC will carry out several different functions depending upon its position in the network. When the MSC provides the interface to PSTN, it will be known as a Gateway MSC (GMSC). In this position it will provide the switching required for all mobile originated or terminated traffic. The GSM network typically contains more than one MSC, each MSC provides service to mobiles located within a defined geographic coverage area. The functions carried out by the MSC are listed below: 1. Call Processing function - Includes of data/ voice call setup, inter - BSS and Inter - MSC Handover and control of mobility management. 2. Operation and Maintenance Supporting function - Includes database management, traffic measurement and a man machine interface. 3. Inter-network & Inter-working function - Manages the interface between the GSM network and the PSTN 4. Billing function- Collects call billing data and transit the bills to the centralized billing center.

Home Location Register (HLR)
Subscriber ID (IMSI and MSISDN) Current subscriber VLR (current location) Supplementary service information Subscriber status (registered/deregistered) Authentication key and AuC functionality The HLR is the database for subscriber parameters. Various identification numbers and addresses are stored as well as authentication parameters. This information is entered into the database by the network operator when a new subscriber is added to the system. The parameters stored in the HLR are listed below: Subscriber ID (IMSI and MSISDN) Current subscriber VLR (Current location) Supplementary service information (e.g. Current forwarding number ) Subscriber status (registered / de-registered ) Authentication key and AUC functionality Temporary Mobile Subscriber Identity (TMSI) Mobile Subscriber Roaming Number (MSRN) The HLR database contains the master database of all the subscribers in GSM system. It’s data can be remotely accessed by all the MSCs and VLRs in the network. Although the network may contain more than one HLR, there is only one database record per subscriber - each HLR is therefore handling a portion of the total subscriber database. The subscriber data may be accessed by either the IMSI or the MSISDN number. The data can also be accessed by an MSC or a VLR in a different network and allow inter-network calling and inter-country roaming.

Visitor Location Register – VLR
Mobile Status (IMSI detached/ attached / busy / idle etc) Location Area Identity(LAI) Temporary Mobile Subscriber Identity (TMSI) Mobile Station Roaming Number (MSRN) The VLR contains a copy of most of the data stored at the HLR. However, It is a temporary data that exists for only as long as the subscriber is "active" within the VLR coverage. So, the VLR provides a temporary local database for the subscriber. This function reduces the need for excessive and time-consuming references to the "home" HLR database. The additional data stored in the VLR is listed below: Mobile status (busy /free/no answer etc.) Location Area Identity (LAI) Temporary Mobile Subscriber Identity (TMSI) Mobile Station Roaming Number(MSRN)

Equipment Identity Register – EIR
White List Black List Grey List IMEI Is Checked against White List If NOT found The EIR contains a centralized database for validating the International Mobile Equipment Identity (IMEI). This database is concerned solely with MS equipment and not with the subscriber. The EIR database consists of lists of IMEIs organized as follows: 1. WHITE LIST contains those IMEIs that have been assigned to valid mobile Equipment. 2. BLACK LIST Contains IMEIs of mobiles which have been reported stolen or which are have forbidden service for some other reason. 3. GREY LIST Contains IMEIs of mobiles that have problems (e.g. faulty software). These are not sufficiently significant to enter into a "black list". EIR focus on the equipment, not the subscriber!! IMEI Is Checked against Black/Grey List

Authentication Center (AuC)
HLR IMSI(m) KI（M) VLR SIM IMSI(n) KI（N) KI(IMSI) RAND GENERATOR A8 A3 AUTH REQ RAND KC SRES KI(IMSI) CKSN RAND IMSIBUFFER RAND A8 A3 RAND KC SRES 1 2 5 KC BSS RAND KC SRES KC SRES TEMP DATA SRES SRES The AUC is a processor system. It performs the "authentication " function. It will normally be co -located with the HLR. The authentication process will usually take place each time the subscriber "initializes "on the system. In the authentication process, secure data stored on the SIM card is calculated and compared with the data held in the HLR database. The Authentication Process is as follows: A random number is sent to the Mobile from the AUC. This number is calculated together with Authentication Key (Ki) stored in the SIM card by authentication algorithms, which is held in the SIM card. The calculation of the random number and Ki will get two results. One is a response called as SRES, which are returned to the AUC. Another is an Encryption Key called as Kc which is stored in the SIM card. The Encryption key is used to encrypt data that is sent over the air interface in order to make the interface more secure. 1. While the mobile is carrying out these calculations, the AUC carries out exactly the same calculations using the random number and ki stored in the HLR. Then AUC also gets a response. 2. The AUC compares it with the response from the subscriber. If the responses produced by the AUC and the subscriber are the same, the subscriber is permitted to access the network. 3. The Encryption Key produced by the AUC is stored and sent to the BTS to enable ciphering to take place. The first time a subscriber attempts to make a call, the full authentication process takes place. However, for subsequent calls, authentication may not be necessary. EQUAL RAND KC SRES RAND 16byte KI 16byte kc 8byte SRES 4byte CKSN low 3bits of 1byte

Inter-Working Function – IWF
Rate Conversion Protocol Adaptation MSC The IWF provides the function to enable the GSM system to connect with the various forms of data networks. The basic features of the IWF are listed below: Rate Conversion function Protocol Adaptation function GSM system may require IWF capability or not. This depends upon the network to which it is being connected. PSTN EC IWF Eg. Fax, Modem

Echo Canceller － EC Generation of Echo at 2-wire to 4-wire Interface
Echo takes place by GSM system delay caused by call processing,speech encoding and decoding etc. An Echo Canceller is used on the PSTN side of the MSC for all voice circuits 2- wire 4- Hybrid Generation of Echo at 2-wire to 4-wire Interface An Echo Canceller is used between PSTN and MSC for all voice circuits. Echo control is required at the MSC because the GSM system delay can cause an unacceptable echo condition even on a short distance with PSTN. The GSM system delay may be caused by call processing, speech encoding and decoding etc. The total round trip delay is approximately 180ms. This would not be apparent to the call between MS. But this case will be very different for the call between MS and land subscriber. It is well known that, in the PSTN a 2- wire to 4- wire hybrid transformer is required in the circuit because the standard telephone connection is 2- wire. This transformer causes the echo, which does not affect the land subscriber. During a normal PSTN land to land call, no echo is apparent because the delay is too short and the user is unable to distinguish. However, with the GSM round trip delay added and without the EC, the effect would be very irritating to the MS subscriber and disrupting speech. Thus, Echo controller is required between PSTN and MSC.

Operation and Maintenance Sub System
NOC OMC OMC OMC The operation and maintenance subsystem provides a capability to manage the GSM network remotely. Operation and Maintenance Center is a centralized facility that supports daily management for the whole GSM system including MSC, HLR, BSC and BTS. The OMC provides a central point from which to control and monitor the whole network entities as well as monitor the quality of service provided by the network. Because GSM does not specified the OMC specification and it is left to the network operator to decide what capabilities they wish it to have. Thus, at present, GSM manufacturers have their own OMCs, which are not compatible with those of other manufacturers. Generally, an OMC only manages a certain area of GSM network. Another equipment Network Operation Center-NOC should be mentioned here. NMC has a view of the entire PLMN and is responsible for the management of the network as a whole. The NMC locates at the top of the hierarchy and provides global network management. Region2 Region 3 Region 1

OMC Functional Architecture
OS MMI DB Event/Alarm Management Security Configuration Performance Management Fault Management The OMC Functional Architecture is illustrated in this diagram: The OMC should support the following functions as recommendations: 1. Event/Alarm Management 2. Fault Management 3. Performance Management 4. Configuration Management 5. Security Management

Example: Baghdad OMC

GSM Interface D HLR G H AUC VLR VLR C EIR B F MSC MSC E IWF EC EC IWF
Each GSM component is designed to communicate over an interface specified by the GSM standards. This provides flexibility and enables a system operator to adopt system components from different manufacturers. For example Motorola BSS equipment may be coupled with a Huawei NSS. Each interface within the GSM system has a specified name associated with it. This table illustrates the names of all the interfaces specified by GSM. NameInterface Um MS  BTS Abis BTS  BSC A BSC MSC B MSCVLR C MSCHLR D VLR HLR E MSCMSC F MSCEIR G VLR VLR H HLR AUC This section will introduce the terrestrial interfaces. It comprise all the connections between the GSM system entities, while the Um, or air – interface is not included since it belongs to radio interface and will be introduce in the next section. IWF EC EC IWF A TC Abis Um MS BTS BSC

GSM Protocol Stack CM: Call Management MM: Mobility Management
RR: Radio Resource Management LAPDm: LAPD modified LAPD: Link Access Procedure on D Channel BTSM: BTS Site Management MTP: Message Transfer Part SCCP: Signaling Connection Control Part BSSMAP: BSS Management Application Part

ITU Signaling System CCS7
CCS7 Levels OSI Layers 7. Application 6. Presentation 5. Session 4. Transport 3. Network 2. Link 1 Physical MTP Level Mb/s Trunk MTP Level 3 TUP SCCP BSSAP (DTAP+BSSMAP) ISUP MAP TCAP MTP Level 2 This diagram illustrates the use of CCS7 in the GSM system, carrying signaling and control information between most major entities and to and from the PSTN. The following message protocols, which are part of CCS7, are used to communicate between the different GSM network entities. The structure of CCS7 conforms to OSI structure. The left side is OSI 7 layer. The right side is the CCS7 used in GSM system. The first level is physical layer with 2Mbps trunk, also called as MTP level 1. The second level is link layer with MTP level 2 The third level is network layer with MTP level 3 and SCCP. The layers from layer 4 to layer 6 are not used in GSM CCS7 structure. The seventh level is application layer, such as TUP, ISUP, MAP, TCAP and BSSAP.

Abbreviation of CCS7 MTP Message Transfer Part
TCAP Transaction Capabilities Application Part SCCP Signaling Connection Control Part TUP Telephone User Part ISUP ISDN User Part MAP Mobile Application Part BSSAP Base Station System Application Part BSSMAP BSS Management Application Part DTAP Direct Transfer Application Part This slide lists the abbreviation of CCS7. MTP Message Transfer Part TCAP Transaction Capabilities Application Part SCCP Signaling Connection Control Part TUP Telephone User Part ISUP ISDN User Part MAP Mobile Application Part BSSAP Base Station System Application Part BSSMAP BSS Management Application Part DTAP Direct Transfer Application Part As for the detailed description, please refers to the course of CCS7

2MBps Trunks Typical Configuration TS 0 TS 1-15 TS16 TS 17-31
TS = Time slot TS# Used for This diagram illustrates the structure of 2Mbps. Each is a Mbps link provides 30*64Kbps channels available to carry speech, or data and two channels for control information. The speech or data channels may contain CCS7 LAPD or X.25 formatted information. Therefore, these 2Mbps links commonly act as the physical bearer for all the interfaces used between the GSM system entities. Synchronization / Clock 1-15 Traffic 16 CCS7 Signaling (Other TS may also the used) 17-31 Traffic

SigL1: 2MBps Trunks PSTN HLR AUC OMC IWF EIR MSC/VLR MSC/VLR EC EC TC
The GSM interfaces conform to ITU specifications, which widely used throughout the world. This diagram shows the GSM system with the 2Mbps interfaces, which are highlighted. These interfaces carry traffic from the PSTN to the MSC, between MSCs, from an MSC to a BSC and from a BSC to remotely sited BTSs. These links are also used between the MSC and IWF. TC PSTN BSC BTS BTS

CCS7 Interface This slide introduces the CCS7 protocols used on the GSM interfaces. Inter - facing the PSTN, the MSC performs call signaling functions using the Telephone User Part (TUP) while inter - facing the ISDN, the ISDN User Part (ISUP) will be used. Between the MSC and the BSC, the Base Station System Management Application Part (BSSMAP) is used. The Direct Transfer Application Part (DTAP) is used to send messages between the MSC and the mobile station (MS). MAP is used between the MSC and the VLR, EIR, and HLR.

LAPD Interface Abis is the interface between BSC and BTS. Because the GSM specifications for this interface are not very specific, therefore Abis interface is not an open and standard interface. Thus, the Abis interface of different manufacturers is varied. This means that one manufacturer's BTS will not work with another manufacturer's BSC. That is to say, BSC and BTS must come from the same manufacture. Through Abis interface, a different type of protocol is required. GSM has specified the use of LAPD protocol in Abis interface.

...... System area Service Area PLMN service area Radio cell
MSC service area... Location area... Base station area... Radio cell MS service area is subdivided into following six levels: System area, PLMN service area, MSC service area, Location area, Base station area, and radio cell The System area comprises one or more international PLMN service area. In this area, the other users from PLMN、PSTN and ISDN can connect with the MS without knowing where it is. PLMN service area is served by one operator. The PLMN service area is served by one or more HLR. There are the same numbering plan and the routing plan in PLMN service area. PLMN service area comprises one or more MSC service area. MSC service area is served by one MSC. It may be a part of a city or an entire country area. MSC service area comprises one or more Location area. Location area is determined by the operator to fulfill the requirements imposed by traffic and flow, population density and subscriber mobility. Location area comprises one or more Base station area. Base station area is served by one or more BTS. It consists of one cell if the antenna is omni-directional, or more than one cell if the antenna is directional. Base station area comprises one or more radio cell. Radio cell is served by a directional or omni-directional antenna. It is the smallest service area in GSM system. In radio cell, specific radio channel devices are used for each radio connection.

MSC/VLR Number CC NDC LSP The format is CC+NDC+LSP CC：Country Code.
For example: The CC of Iraq is “964". NDC：National Destination Code. For example: The NDC of AsiaCell is 770. LSP (locally significant part): is defined by Telecom operator. For example: In the GSM system, For identification purpose, We defined the number for GSM system equipment, mobile subscriber, mobile equipment and cell. MSC/VLR number is used to identify MSC/VLR. The format is CC+NDC+LSP CC means Country Code. For example: The CC of Iraq is “964". NDC means National Destination Code. For example: The NDC of Asiacell is 770. LSP means Locally Significant Part. It is defined by Telecom operator. For example, a MSC/VLR number is Since the MSC and the VLR are usually co-located together, so the MSC-Number and the VLR-Number are the same in most case.

HLR Number The format is：CC + NDC + LSP. CC：Country Code.
For example: The CC of Iraq is “964". NDC：National Destination Code. For example: The NDC of Asiacell is 770 LSP (locally significant part): is defined by Telecom operator. For example: HLR number is used to identify HLR. The format is：CC+NDC+LSP. CC： Country Code. For example: The CC of Irag is “964". NDC：National Destination Code. For example: The NDC of Asiacell is 770. LSP (locally significant part): is defined by Telecom operator. For example:

Location Area Identification
LAI MCC MNC LAC Location Area Identification The LAI is the international code for a location area. MCC：Mobile Country Code，It consists of 3 digits . For example: The MCC of Iraq is “418" MNC：Mobile Network Code，It consists of 2 digits . For example: The MNC of Asiacell is "05" LAC： Location Area Code，It is a two bytes BCD code(hex). The value 0000 and FFFF is invalid. For example: AB LAI means Location Area Identification. The LAI is a unique international identification for a location area. The format is MCC+MNC+LAC MCC：Mobile Country Code，It consists of 3 digits . For example: The MCC of Iraq is “418" MNC：Mobile Network Code，It consists of 2 digits . For example: The MNC of Asiacell is "05" LAC： Location Area Code，It is a two bytes BCD code(hex). The value 0000 and FFFF is invalid. For example: AB E.164 = CC + NDC + … (MSC/VLR, HLR, MSISDN) E.212 = MCC + MNC + … (IMSI)

CGI The CGI is a unique international identification for a cell
CGI: Cell Global Identification The CGI is a unique international identification for a cell The format is LAI+CI LAI: Location Area Identification CI：Cell Identity. This code uses two bytes BCD code(hex) to identify the radio cells within an LAI. For example : AB-CD98 CGI means cell global identification. The CGI is a unique international identification for a cell. The format is LAI+CI LAI：Location Area Identification CI：Cell Identity. This code uses two bytes BCD code (hex) to identify the radio cells within a LAI. For example of CGI: AB-CD98

BSIC NCC BCC BSIC BSIC（Base Station Identification Color Code)
NCC：PLMN network color code. It comprises 3 bit. It allows various neighboring PLMNs to be distinguished. BCC：BTS color code. It comprises 3 bit. It allows distinction between different radio frequency channels using the same frequency in neighboring cells. BSIC means Base Station Identification Color Code The structure of BSIC shows in this diagram. NCC----PLMN network color code. It comprises 3 bits. It allows various neighboring PLMNs to be distinguished. BCC----BTS color code. It comprises 3 bits. It allows distinction Between different radio frequency channels using the same frequency in neighboring cells.

National (significant) Mobile station international
MSISDN CC NDC SN National (significant) Mobile number Mobile station international ISDN number CC： Country Code. For example: The CC of Iraq is “964". NDC：National Destination Code. For example: The NDC of Asiacell is 770. SN： Subscriber Number. Format:H0 H1 H2 ABCD Example: MSISDN is used in the following cases: By the caller to set up a connection to this mobile subscriber By the MSC/Gateway MSC to address the HLR when inquiring the visitor location of the mobile subscriber. MSISDN is stored as semi-permanent data in the database of HLR and VLR. It is transferred on MAP interface. The structure of MSISDN is shown in this diagram. CC： Country Code. For example: The CC of Iraq is “964". NDC：National Destination Code. For example: The NDC of Asiacell is 770. SN： Subscriber Number. Format:H0 H1 H2 ABCD Example:

IMSI MCC MNC MSIN Not more than 15 digits 3 digits 2 digits NMSI IMSI
MCC：Mobile Country Code，It consists of 3 digits . For example: The MCC of Iraq is “418"。 MNC：Mobile Network Code，It consists of 2 digits . For example: The MNC of Asiacell is "05"。 MSIN：Mobile Subscriber Identification Number. H1H2H3 ABCDEFG For example: NMSI：National Mobile Subscriber Identification，MNC and MSIN form it together. For Example of IMSI : The IMSI is the unique international code for the mobile subscriber within the GSM system area. But it is not known to the mobile subscriber. IMSI is stored in SIM card and is assigned to the MSISDN in the HLR. It is also stored in HLR and VLR. The structure of IMSI is shown in this diagram MCC：Mobile Country Code，It consists of 3 digits . For example: The MCC of Iraq is “418"。 MNC：Mobile Network Code，It consists of 2 digits . For example: The MNC of Asiacell is "05“. MSIN：Mobile Subscriber Identification Number. H1H2H3 ABCDEFG For example: NMSI：National Mobile Subscriber Identification，MNC and MSIN form it together. For Example of IMSI : Note that IMSI should be not more than 15 digits.

TMSI TMSI: Temporary Mobile Subscriber Identification) The TMSI is assigned only after successful subscriber authentication. The VLR controls the allocation of new TMSI numbers and notifies them to the HLR. TMSI is used to ensure that the identity of the mobile subscriber on the air interface is kept secret. The TMSI consists of 4 bytes( 8 HEX numbers) and determined by the telecom operator. TMSI means Temporary Mobile Subscriber Identification. The TMSI is assigned only after successful subscriber authentication. The VLR controls the allocation of new TMSI numbers and notifies them to the HLR. TMSI is used to ensure that the identity of the mobile subscriber on the air interface is kept secret. The TMSI will be updated frequently; this makes it very difficult for the call to be traced and therefore provides a high degree of security for the subscriber. The TMSI consists of 4 bytes (8 HEX numbers) and determined by the telecom operator.

IMEI Check IMEI by *#06# IMEI
IMEI: International Mobile Station Equipment Identification TAC FAC SNR SP IMEI TAC：Type approval code, 6 bit. It is administered by the type approval center. FAC：Final assembly code, 2 bit. It is administered by the manufacturer. SNR：Serial number, 6 bits. It is issued by the manufacturer of the MS. SP：1 bit, Not used. IMEI means International Mobile Station Equipment Identification. It is the unique number for mobile equipment. Please note the difference between IMSI and IMEI. IMSI is the identification for mobile subscriber, IMEI is the identification for mobile equipment. The structure of IMEI is shown as follows. TAC---Type approval code. It is administered by the type approval center. FAC----Final assembly code. It is administered by the manufacturer. SNR----Serial number. It is issued by the manufacturer of the MS. SP Not used. Check IMEI by *#06#

MSRN/HON MSRN: Mobile Subscriber Roaming Number HON: Hand-over Number
The MSRN is used to route the call to the MSC which MS is currently located. The HON is used by the MSC-A to set up a connection to the MSC-B during handover process Usually, MSRN and HON share the same numbering plan. The format is CC+NDC+individual number. CC and NDC is the same as that of MSISDN. The individual number is taken from a pool of numbers specially reserved for MSRN. MSRN means Mobile Subscriber Roaming Number HON means Hand-over Number The MSRN is not a direct subscriber number. At the request of HLR the VLR allocates a MSRN. Then the MSRN is transferred to the HLR. The HLR passes the MSRN on to the original MSC from which a call is then set up.. The MSRN is then used to route the call to the MSC which MS is currently located. At the end of call setup this MSRN is released again for further call setup processes. So, MSRN is a temporary number. During handover process, For example, when the MS is moving from MSC-A to MSC-B, the MSC-B will request a HON from it's VLR and transfers it to the MSC-A. The HON is used by the MSC-A to set up a connection to the MSC-B. Usually, MSRN and HON share the same numbering plan. The format of MSRN/HON is CC+NDC+individual number. CC and NDC is the same as that of MSISDN. The individual number is taken from a pool of numbers specially reserved for MSRN/HON. In fact, the format of MSRN/HON is based on MSC number and another several digits are added

Multiple Access Technique
Multiple Access Technique allows many subscribers to use the same communication medium. There are three kinds of basic Multiple Access Technique : FDMA , TDMA and CDMA. GSM system adopt FDD-TDMA (FDMA and TDMA together).

FDMA FDMA uses different frequency channels to accomplish communication. The whole frequency spectrum available is divided into many individual channels (for transmitting and receiving)，every channel can support the traffic for one subscriber or some control information. Frequency Time

TDMA TDMA accomplishes the communication in different timeslot.
A carrier is divided into channels based on time. Different signals occupy different timeslots in certain sequence , that is , many signals are transmitted on the same frequency in different time. Frequency Time

CDMA CDMA accomplishes the communication in different code sequences.
Special coding is adopted before transmission, then different information will lose nothing after being mixed and transmitted together on the same frequency and at the same time. Frequency Code Time

Physical Channel and Logical Channels
The physical channel is the medium over which the information is carried: 200KHz and 0.577ms The logical channel consists of the information carried over the physical channels 1 2 3 4 5 6 7 1 2 3 The channels used in the air interface are divided into two types: physical channel and logical channel. The physical channel is the medium over which the information is carried, in the case of a terrestrial interface this would be a cable. The logical channels consist of the information carried over the physical channel. First physical channels will be introduced. A single GSM RF carrier can support up to eight mobile subscribers simultaneously. This diagram shows how this is accomplished. Each channel occupies the carrier for one eighth of the time. This is a technique called Time Division Multiple Access (TDMA). Time is divided into discrete periods called "time slot". The time slots are arranged in sequence and are conventionally numbered 0 to 7. Each repetition of this sequence is called a "TDMA frame". Each mobile telephone call occupies one time slot (0-7) within the frame until the call is terminated, or a handover occurs. The TDMA frames are then built into further frame structures according to the type of channel. We later shall introduce how the information builds into frames and multi – frames. The information carried in one time slot is called a "burst". Each data burst occupies its allocated time slot and provides a single GSM physical channel. Timeslot The information carried in one time slot is called a “burst” TDMA FRAME TDMA FRAME

Two types of Logical Channel
Traffic Channel (TCH) : Transmits traffic information, include data and speech. Control Channel (CCH) : Or Signaling Channel, transmits all kinds of control information.

Traffic Channel (TCH) TCH Traffic Channels Speech Data TCH/FS TCH/HS
Normal Burst Speech Data TCH/FS TCH/HS There are two main groups of logical channels, traffic channels and control channels. The traffic channel carries speech or data information. A full rate TCH/F carries information at a gross rate of 22.8kbps. The raw data rate for each TCH is 13kbps and 9.6kbps, 4.8kbps and 2.4kbps for data A half rate TCH/H carries information at half of the full rate channel or at the gross rate of 11.4kbps. The data rate associated with the half rate TCH are 4.8kbps and 2.4kbps. The different types of traffic channel are listed below: TCH/FS Full rate speech channel TCH/HS Half rate speech channel TCH/F Kbps full rate data channel TCH/F Kbps full rate data channel TCH/F Kbps full rate data channel TCH/H Kbps half rate data channel TCH/H Kbps half rate data channel TCH/9.6 TCH/2.4 TCH Traffic Channel TCH/FS Full rate Speech Channel TCH/HS Half rate Speech Channel TCH/9.6 Data Channel 9.6kb/s TCH/4.8 Data Channel 4.8kb/s TCH/2.4 Data Channel 2.4Kb/s TCH/4.8

Control Channel (CCH) CCH Control Channels FCCH SCH DCCH SDCCH BCCH
Synch. CH. ACCH SACCH FACCH CCCH RACH CBCH PCH/AGCH There are four main groups of control channel that are listed below: Broadcast Control Channel – BCCH: Transmitted at all times convey information about cell timing and configuration. Common Control Channel – CCCH: Used by BSS and MS when trying to initiate a connection over the air. Dedicated Control Channel – DCCH: This dedicated channel is used to convey signaling information during call set - up. Associated Control Channel – ACCH: The associated channels are used to transmit signaling information when a call is in progress. Broadcast Control Channel – BCCH Common Control Channel – CCCH Dedicated Control Channel – DCCH Associated Control Channel – ACCH

Broadcast Control Channel – BCCH
downlink only Synch. Channels SCH FCCH The information carried on the BCCH is monitored by the MS periodically when it is in idle mode BCCH: Broadcast Control Channel FCCH: Frequency Correction Channel SCH: Synchronization Channel The Broadcast Control Channel is transmitted by the BTS at all times. The RF carrier used to transmit the BCCH is called as the BCCH carrier. The information carried on the BCCH is monitored by the mobile periodically (at least every 30s) when it is switched on and not in a call. Broadcast Control Channel (BCCH) - Carries the following information (this is only a partial list): Location Area identity (LAI) List of neighboring cells that should be monitored by the mobile List of frequencies used in the cell Cell identity Power Control indicator DTX permitted Access Control (e.g. Emergency calls, call barring) CBCH description The BCCH is transmitted at constant power at all times and its signal strength is measured by all mobiles which may seek to use it. Frequency Correction Channel (FCCH) is transmitted frequently and is more easily detected by the mobile than SCH. When the FCCH is detected, the mobile corrects the frequency. It is then able to detect the SCH which contains the precise synchronization information. Synchronization Channel (SCH) carries the information to enable the mobile to synchronize to the TDMA frame structure. The following parameters as also carried. Frame Number Base Site Identity Code (BSIC) The mobile will monitor BCCH information from surrounding cells and store the information from the best six cells. The SCH information on these cells is also stored so that the mobile may quickly re-synchronize when it enters a new cell.

Common Control Channel – CCCH
The CCCH is responsible for transferring control information between all mobiles and the network. RACH: Random Access Control Channel PCH: Paging Channel AGCH: Access Grant Control Channel CBCH: Cell Broadcast Channel CCCH RACH uplink CBCH downlink The common control channel (CCCH) is responsible for transferring control information between all mobiles and the BTS. This is necessary for the implementation of "call origination" and "call paging" functions. It consists of the following types: Random Access Control Channel (RACH) - Transmitted by the mobile when it wishes to access to the system. This occurs when the mobile initiates a call or responds to a page. Paging Channel (PCH) - Transmitted by the BTS when it wishes to contact a mobile. Access Grant Control Channel (AGCH) - Transmitted by the BTS. The AGCH is used to assign dedicated resources to an MS such as a Standalone Dedicated Control Channel (SDCCH). Cell Broadcast Channel (CBCH) - This channel is used to transmit messages to be broadcast to all mobiles within a cell e.g. traffic info. The CBCH will steal time from an SDCCH. Active mobiles must frequently monitor both BCCH and CCCH. The CCCH will be transmitted on the RF carrier with the BCCH. PCH/AGCH downlink

Dedicated Control Channel – DCCH
DCCH is assigned to a single mobile connection for call setup or for measurement and handover purpose. SDCCH: Standalone Dedicated Control Channel ACCH: Associated Control Channel SACCH: Slow Associated Control Channel FACCH: Fast Associated Control Channel DCCH SDCCH ACCH Dedicated control channels (DCCH) are assigned to a single mobile connection for call setup or for measurement and hand over purposes: Standalone Dedicated Control Channel (SDCCH) - This supports the transfer of data to and from the mobile during call setup. It also carries information for call forwarding and transmission of short messages. Associated Control Channels – ACCH These channels can be associated with either an SDCCH or a TCH. They are used for carrying information associated with the process being carried out on either the SDCCH or the TCH. Slow Associated Control Channel (SACCH) - Conveys power control and timing information in the downlink direction (towards the MS) and Receive Signal Strength Indicator (RSSI) and link quality reports in the uplink direction. Fast Associated Control Channel (FACCH) - the FACCH is transmitted instead of a TCH. The FACCH "steals" the TCH burst and inserts its own information. The FACCH is used to carry out user authentication and handover. FACCH SACCH

Uplink Logical channel
RACH CCCH CCH SDCCH SACCH FACCH TCH/F TCH/H DCCH TCH DCH

Downlink Logical channel
FCCH SCH BCCH PCH AGCH CCCH CCH SDCCH SACCH FACCH TCH/F TCH/H DCCH TCH DCH

How to use these channel?
Power-off state Search for frequency correction pulse Search for synchronous pulse Unscramble system information Snoop into paging message Send access pulse Allocate signaling channel Set up the call Allocate voice channel Conversation Release the call FCCH SCH BCCH PCH RACH AGCH SDCCH FACCH TCH Idle state Dedicated mode Idle state

Channel Combination GSM Logical Channel
Main BCCH combination – BCCH + CCCH SDCCH combination – SDCCH8 + SACCH8 Combined BCCH – BCCH + CCCH +SDCCH4 + SACCH4 TCH combination – TCH/FACCH + SACCH The different logical channel types mentioned previously are grouped into what are called channel combinations. The four most common channel combinations are listed below: 1. Full Rate Traffic Channel Combination - TCH/FACCH + SACCH 2. Broadcast Channel Combination - BCCH + CCCH 3. Dedicated Channel Combination - SDCCH8 + SACCH8 4. Combined Channel Combination - BCCH + CCCH + SDCCH4 + SACCH4

GSM Multiframe CONTROL CHANNELS TDMA Frames 1 1 2 3 4 46 47 48 49 50
1 1 2 3 4 5 6 7 1 2 3 4 5 6 7 1 2 3 4 46 47 48 49 50 This multi-frame structure for control channels is different from traffic channel. The diagram shows the time relationship between time slot, TDMA frame, and multi-frame for control channels. Control channels occupy a 51 - frame multi-frame structure. 51 – Frame Multiframes CONTROL CHANNELS

BCCH/CCCH Multiframe Downlink Uplink F = FCCH (Frequency)
S B C F S C I S C C .. F S C C .. F S C C .. F = FCCH (Frequency) S = SCH (Sync.) C = CCCH (Common) I = Idle R = RACH (Random) The 51 - frame structure used for control channels is considerably more complex than the 26 frame structure used for the traffic channels. The 51 – frame multi-frame structure occurs in several forms, depending on the type of control channel and the system operator's requirements. This diagram gives an example. In the downlink direction (from BSS to MS), the time slot is shared by several logical channel types. Some of the channels are repeated frequently e.g. SCH and FCCH while others less frequently e.g. BCCH. In the uplink direction (from MS to BSS), all time slots are allocated to RACH. This is because RACH is the only control channel in the BCCH/CCCH group, which operates in the uplink direction. Uplink R R R R R .. R R R ..R R R ..

SDCCH Multiframe Downlink D0 D1 D6 D7 A0 A3 I I I D0 D1 D6 D7 A4 A7 I
D = SDCCH/8 (Dedicated) A = SACCH/C8 (Associated) I = Idle The 51 - frame structure used for control channels is considerably more complex than the 26 frame structure used for the traffic channels. The 51 – frame multi-frame structure occurs in several forms, depending on the type of control channel and the system operator's requirements. This diagram gives an example. In the downlink direction (from BSS to MS), the time slot is shared by several logical channel types. Some of the channels are repeated frequently e.g. SCH and FCCH while others less frequently e.g. BCCH. In the uplink direction (from MS to BSS), all time slots are allocated to RACH. This is because RACH is the only control channel in the BCCH/CCCH group, which operates in the uplink direction. This diagram shows the 51 - frame structure used to accommodate 8 SDCCHs although, as it takes two repetitions of the multi-frame to complete the entire sequence, it may be more logical to think of it as a frame structure! This structure may be transmitted on any time slot. Note that the 8 SACCHs (shaded) are associated with the 8 SDCCHs. It is important to remember that each SDCCH has an SACCH just like a traffic channel. Uplink A5 A6 A7 I I I D0 D7 A0 A1 A2 A3 I I I D0 D7 A4

Timeslots and TDMA Frames
Higher Capacity Cell Broadcast Traffic Dedicated 1 2 3 4 5 6 7 Now the relation between Channel Combinations and Time slots will be introduced. The channel combinations are sent over the air interface in a selected time slot. Some channel combinations may be sent on any time slot but others must be sent specific time slots. Below is a table mapping the channels combination to their respective time slots. Channel CombinationTime slots TrafficAny time slotBroadcast0,2,4,6(0 must be used first) DedicatedAny time slot Combined0 only This diagram gives an example. In the low capacity cell, ts0 is used as combined channel, while other time slots used for traffic channels. In the higher capacity cell, ts0 is used as broadcast channel, ts1 is used as dedicated channel, while other time slots used for traffic channels. Low Capacity Cell Combined Traffic 1 2 3 4 5 6 7

Combined Multiframe B S F C D0 D1 D2 D3 A0 A1 I A2 A3
Downlink R Uplink R = RACH (Random) B = BCCH (Broadcast) F = FCCH (Frequency) S = SCH (Sync.) C = CCCH (Common) D = SDCCH/4 (Dedicated) A = SACCH/4 (Associated) I = Idle This diagram illustrates the 51 - frame Control Channel combined Multi-frame. In this configuration the BCCH and SDCCH share a common time slot, this means that each logical channel has less time than it would if one of the other configurations were used. Because each channel has less time, fewer subscribers can be supported. Therefore the combined channel combination is used in areas where traffic density is low. Like the SDCCH multi-frame, it takes two repetitions of the 51 - frame multi-frame to complete the sequence, this is really a frame structure.

GSM Multiframe TRAFFIC CHANNELS TDMA Frames 1 1 2 3 4 21 22 23 24 25
1 1 2 3 4 5 6 7 1 2 3 4 5 6 7 1 2 3 4 21 22 23 24 25 This diagram illustrates how these different channel combinations may be mapped onto the TDMA structure. Several logical channels share one time slot. The individual channels are sequenced so that each receives the amount of time it requires. This sequencing is carried out by the use of multi-frames, each channel combination has a different multi-frame configuration. This diagram shows the time relationship between time slot, TDMA frame, and multi-frame for traffic channels. Traffic channels occupy a 26 - frame multi-frame structure. 26 – Frame Multiframes TRAFFIC CHANNELS

TCH Multiframe Downlink Uplink 25 12 IDLE SACCH 25 12 IDLE SACCH This is used to transmit a Traffic Channel Combination (TCH/ SACCH/FACCH). The FACCH is not showed in the diagram as it does not receive its own time allocation. The FACCH steals a time period from the TCH is required. The 13th frame is used by the SACCH which carriers link control information to and from the mobile and BTS. The 26th frame is idle. This diagram illustrates a 26 frame multi-frame structure, this is used to transmit a Traffic Channel Combination (TCH / SACCH / FACCH). Note the FACCH is not shown in the diagram as it does not receive its own time allocation. The FACCH steals a time period from the TCH when it is required. The 13th frame is used by the SACCH (Slow Associated Control Channel) which carries link control information to and from the mobile and BTS. Also note that the 26th frame is idle which will be used when half rate speech channel is a reality.

Superframe and Hyperframe
By the end of this section, Super frames and hyper frames will be introduced. From the previous slide, we have known that the control channel multi-frame is not a direct multiple of the traffic channel multi-frame. This case is not by accident. From the diagram, it can be seen that any given frame number will only occur simultaneously in both multi-frames every 1326 TDMA frames (26×51). This number of TDMA frames is called a "super frame" and it takes 6.12s to transmit. This arrangement means that the timing of the traffic channel multi-frame is always moving in relation to that of the control channel multi-frame. This enables a mobile to receive and decode BCCH information from surrounding cells. If the two multi-frames were exact multiples of each other, then control channel time slots would be permanently 'masked' by traffic channel time slot activity. This changing relationship between the two multi-frames is particularly important. The "hyper frame" consists of 2048 super frames, this is used in connection with ciphering and frequency hopping, the hyper frame lasts for over three hours, after this time the ciphering and frequency hopping algorithms are restarted.

Modulation Techniques
Amplitude Modulation (AM) Frequency Modulation (FM) Phase Modulation (PM) – phase modulation can be implemented easily for digital signals, this is the method which is used for the GSM air interfaces. Phase Modulation is known as Phase Shift Keying when applied to digital signals It is well known that there are three methods of modulating a signal so that it may be transmitted over the air: 1、Amplitude Modulation (AM) 2、Frequency Modulation (FM) 3、Phase Modulation (PM) The modulator causes the frequency, amplitude or phase of an RF carrier to be varied in proportion to the signal it is going to carry. GSM uses a digital air interface. It means that digital signals are transmitted on the radio channel. Digital signals can use any of the modulation methods but phase modulation provides the best noise tolerance. Since phase modulation can be implemented easily for digital signals, this is the method, which is used for the GSM air interface. Phase Modulation is known as Phase Shift Keying when applied to digital signals.

Gaussian Minimum Shift Keying (GMSK)
Gaussian Digital Filter Phase Modulator Phase Modulation provides a high degree of noise tolerance, however there is a problem with this modulation. When the signal changes phase abruptly, high frequency components are produced, thus, a wide bandwidth would be required for transmission. We have mentioned previously that GSM has a narrow bandwidth and to be as efficient as possible with the available bandwidth. Therefore, a more efficient development of phase modulation called as Gaussian Shift Keying(GMSK) is actually used by the GSM air interface. With GMSK the phase change does not occur instantaneously. Instead it occurs over a period of time and therefore the addition of high frequency components to the spectrum is reduced. With GMSK, first the digital signal is filtered through a Gaussian filter. This filter causes distortion to the signal, the corners are rounded off. This distorted signal is then used to phase shift the carrier signal. The phase change therefore is no longer instantaneous but spread out.

Power Control Both Uplink and Downlink power settings can be controlled independently and individually. 8W 0.8W POWER CONTROL is a feature of the GSM air interface which allows the operator to not only compensate for the distance from mobile to BTS as regards timing, but can also cause the BTS and mobile to adjust their power output. This feature saves radio battery power at the mobile, and helps to reduce co -channel and adjacent channel interference. Both Uplink and Downlink power settings can be controlled independently and individually. Initial power setting for the MS is set by the information provided on Broadcast Control Channel (BCCH) for a particular cell. The BSS controls the transmit power of both the mobile and the BTS .The received mobile power is monitored by the BSS and the receive BTS power is monitored by the mobile and then reported to the BSS. Using these measurements the power of both mobile and BTS can be adjusted accordingly 5W Saves radio battery power Reduces co-channel and adjacent channel interference

Voice Activity Detection – VAD
VAD and DTX Voice Activity Detection – VAD Discontinuous Transmission – DTX Battery Saving Interference reduction

Multipath Fading Diversity Frequency Hopping Time Dispersion
Multi path Fading results from a signal traveling from a transmitter to a receiver by a variety of routes. This is caused by the signal being reflected from objects, or being influenced by atmospheric effects as it passes, for example, through layers of air of varying temperatures and humidity. The received signals will therefore arrive at different times and not be in phase with each other, they will have experienced time dispersion. When the receive antenna is moving, the exact phase of each path changes and consequently the combined signal-strength is also continually changing. GSM offers many techniques, which combat multi-path fading effects. In the following, Diversity and Frequency Hopping will be introduced.

Diversity Approx. 10 wavelengths
When diversity is implemented two antennas are situated at the receiver. These antennas are placed several wavelengths apart to ensure minimum correlation between the two receive paths. Compare or add signals Signals arrive at the receive antenna from multiple paths. The signals are therefore received by the antenna at different phases, some at a peak and some at trough. This means that some signals will add together to form a strong signal while others will subtract causing a weak signal When diversity is implemented, two antennas are situated at the receiver. These antennas are placed several wavelengths apart to ensure minimum correlation between the two receive paths .The two signals are then combined, this ensures that a low signal strength is less likely to occur. The two signals are then combined, this ensures that a low signal strength is less likely to occur. Resultant Signal

Frequency Hopping Each time the BTS or mobile transmits a burst, it does so on a different RF carrier frequency. frequency Synthesizer Hopping:each timeslot on a given transceiver can transmit at a different frequency Baseband Hopping: each transceiver stays at the same frequency and the data is switched to the appropriate transceiver. Frequency hopping means each time the BTS or mobile transmits a burst on a different RF carrier frequency. In one way, Frequency hopping brings the security benefit to GSM system. The other main reason is to reduce multi path fading effects The hopping must use a predetermined sequence so that both transmitter and receiver must hop in synchronization. This sequence is stored in a 'frequency hopping table'. Care should be taken to that BCCH is not frequency hopped and it is always transmitted at the same frequency. This is because the BCCH in any cell must be transmitted on a dedicated RF carrier ,otherwise mobiles would be unable to find and decode it. There are two methods of frequency hopping, Synthesizer Hopping and Baseband Hopping. Both are slow frequency hopping techniques. This means that the frequency of the transmission only changes once every time a burst is transmitted. In Synthesizer Hopping, each time slot on a given transceiver can transmit at a different frequency. The transceiver retunes between time slots. This is an efficient method for small sites with few transceivers. In Baseband Hopping, each transceiver stays at the same frequency and data is switched to the appropriate .The numbers of hopping frequencies is limited to the number of transceivers. time

GSM Network Components Terrestrial Interface Service Area and Number Planning Channels on The Air Interface Radio Technologies The Future Development

Mobile usage overtakes fixed
GSM User World Wide Millions 200 400 600 800 1000 1200 1400 1600 1800 1999 2000 2001 2002 2003 2004 2005 Mobile will be the most prolific form of access to internet-based information, content and services Mobile subscribers Mobile usage overtakes fixed Fixed line (dial-up) subscribers 500m Mobile users PC/NC Internet users Nowadays, The mobile communication market has experienced rapid growth. GSM system wins widely market applications. However, it represents a large and continuously increasing percentage of all new mobile subscribers in the world. All professional Market Forecasts say GSM will stay in the Lead in the recent several years. From this diagram, you can know about the average growth of GSM mobile subscribes in the world. Last year, the number of mobile subscribers reaches more than 1400millions. Mobile Internet access overtakes fixed Mobile Internet users Source: Ericsson Business Consulting

Number of Wireless Subscribers*
Iraq Asiacell 6,686,140 Zain 10,111,000 Korek Telecom 665,361 Sanatel 361,431 Thailand AIS 27,581,800 DTAC 18,945,227 TRUE 15,004,000 China China Mobile 477,160,000 China Unicom 133,365,000 World 4,153,784,344 *Update Q1, 2009 from

Technology Roadmap 1992 1999 2000 2002 GSM (2G) WAP HSCSD GPRS (2.5G)
EDGE (2.75G) UMTS (3G) 9.6 38.4 64-115 384 Up to 2Mb/s? DATA SPEED Kbit/s Driven by the market force, cellular system experienced three generations. GSM and DCS 1800 belong to Second Generation cellular technologies In recent years second generation technologies have been developed to GPRS called 2.5G to support high-speed data packet services. Its maximum rate can reach 115kbps. A third generation system is being developed. It aims at integrating and merging a range of communication services and providing high-speed and wide-band services. GSM will become the basis for the Third Generation (3G) system will evolve from GSM. The maximum rate of Mobile multimedia services can reach 2Mbps. DEVICES

Mobile Service Evolution
Dial-up connections Accelerated connections, voice and data multitasking Corporate access Always-on, performance and security enhancements Messaging Hi, I’ll see you at 6 PM Regards, Bob Multimedia messaging with video Multimedia messaging with pictures and audio Basic text messaging Black and white screens, simple graphics Browsing Instant connectivity, color screen, WAP Push xHTML for WAP and web integration, animated content Ringing tones, icons, screensavers, business cards Downloading Downloadable applications, MIDI sounds Video content (MMS, streaming)

Summary Basic Concepts of Cellular Mobile System
GSM Network Components Terrestrial Interface Service Area and Number Planning Channels on The Air Interface Summary: The contents of this course are mainly divided into seven sections: Section 1 deal with principles of the Cellular Telecommunication, where we discuss the concepts of cell and frequency spectrum used in cellular system. Section 2 provides a detailed discussion of GSM Network Components and their functions. Section 3 describes service Area and Number Planning Section 4 is devoted to Terrestrial Interface in GSM system. Section 5 provides a detailed discussion of Channels on the Air Interface Section 6 deals with radio interfaces, where we discuss the basic concepts of radio technologies. Section 7 briefly introduces the Future Development of mobile communication So much for the courses for GSM fundamentals. Thank you. Radio Techniques The Future Development

Thank You By [Technical Trainer]

GSM Fundamentals.

Similar presentations

Presentation on theme: "GSM Fundamentals."— Presentation transcript:

Similar presentations

About project

Feedback

Log in

Auth with social network:

GSM Fundamentals.

Similar presentations

Presentation on theme: "GSM Fundamentals."— Presentation transcript:

Similar presentations

About project

Feedback