1. July 2, 2001Systems Architecture I1 Systems Architecture II (CS 282) Lab 3: State Elements, Registers, and Memory * Jeremy R. Johnson Monday July 2, 2001 *This lecture was derived from material in the text (Appendix B). All figures from Computer Organization and Design: The Hardware/Software Approach, Second Edition, by David Patterson and John Hennessy, are copyrighted material (COPYRIGHT 1998 MORGAN KAUFMANN PUBLISHERS, INC. ALL RIGHTS RESERVED).

2. July 2, 2001Systems Architecture I2 Introduction Objective: Review sequential logic and use of a clock. Provide help with Register File and Memory Unit in VHDL. Topics –Sequential logic (elements with state) and timing (edge triggered) Latches and flip flops Registers –Memory SRAM DRAM

3. July 2, 2001Systems Architecture I3 Timing Clocks used in synchronous logic – when should an element that contains state be updated? –All state elements must have the clock signal as an input Edge-triggered timing –All state elements are updated on the same clock edge cycle time rising edge falling edge

4. July 2, 2001Systems Architecture I4 Edge Triggered Timing State updated at clock edge read contents of some state elements, send values through some combinational logic write results to one or more state elements Clock must have sufficiently long period for combinational logic to stabilize.

5. July 2, 2001Systems Architecture I5 Edge Triggered Timing Allows a state element to be used as both an input and an output

6. July 2, 2001Systems Architecture I6 Components for Simple Implementation Functional Units needed for each instruction

7. July 2, 2001Systems Architecture I7 Register File A set of registers that can be read/written by supplying a register number to be accessed. Built using a decoder for each read and write port, and an array of D flip-flops. For the MIPS processor, the register file has two read ports and one write port. A write flag is used to indicate that the state should change, and a clock is needed to determine when to change state.

8. July 2, 2001Systems Architecture I8 Implementation of Read Ports

9. July 2, 2001Systems Architecture I9 Implementation of Write Ports

10. July 2, 2001Systems Architecture I10 Memory Registers and register files provide the basic building blocks for small memories. Larger memories are built from SRAMs (Static Random Access Memories) and DRAMs (Dynamic Random Access Memories) SRAM –5 to 25 ns access time –largest SRAMs have over 4 Million bits –4 to 6 transistors per bit –value stored in cell kept on a pair of inverting gates and can be kept indefinitely DRAM –60 to 110 ns access time –1 transistor per bit –charge stored in capacitor, and needs periodic refreshing

11. July 2, 2001Systems Architecture I11 Behavioral Model for Memory library IEEE; use IEEE.std_logic_1164.all; use IEEE.std_logic_arith.all; entity memory is port(address, write_data : in std_logic_vector(31 downto 0); MemWrite, MemRead : in std_logic; read_data : out std_logic_vector(31 downto 0)); end memory;

12. July 2, 2001Systems Architecture I12 Behavioral Model for Memory architecture behavorial of memory is type mem_array is array(0 to 7) of std_logic_vector (31 downto 0); begin mem_process: process(address, write_data) variable data_mem : mem_array := ( to_stdlogicvector(X”00000000”), --- initialize data memory to_stdlogicvector(X”00000000”), to_stdlogicvector(X”00000000”)); variable adddr : integer;

13. July 2, 2001Systems Architecture I13 Behavioral Model of Memory begin addr := to_integer(address (2 downto 0)); if MemWrite = ‘1’ then data_mem(addr) := write_data; elsif MemRead = ‘1’ then read_data := data_mem(addr) after 10 ns; end if; end process mem_process; end behavorial;