2. OSHA Office of Training and Education 1 Machine Guarding

3. OSHA Office of Training and Education 2 Introduction Crushed hands and arms, severed fingers, blindness - the list of possible machinery-related injuries is as long as it is horrifying. Safeguards are essential for protecting workers from needless and preventable injuries. A good rule to remember is: Any machine part, function, or process which may cause injury must be safeguarded. Where the operation of a machine can injure the operator or other workers, the hazard must be controlled or eliminated.

4. OSHA Office of Training and Education 3 1.A good rule to remember is: Any machine part, function, or process which may cause injury must be ___________.

5. OSHA Office of Training and Education 4 Causes of Machine Accidents !Reaching in to “clear” equipment !Not using Lockout/Tagout !Unauthorized persons doing maintenance or using the machines !Missing or loose machine guards

6. Machine Guarding !2. List three causes of machine accidents OSHA Office of Training and Education 5

7. 6 Where Mechanical Hazards Occur !Point of operation !All parts of the machine which move, such as: >flywheels, pulleys, belts, couplings, chains, cranks, gears, etc. >feed mechanisms and auxiliary parts of the machine !In-running nip points

8. !Identify and guard all nip points !While patrolling the hog fuel conveyor belt system, a worker noticed a piece of wire caught in the nip point between the hog fuel belt and the head spool. He reached into the nip-point area to remove the wire. As he grabbed the wire, his hand was pulled into the nip point. His arm was crushed when it rotated through the nip point and the head spool. The crushing injury resulted in the amputation of his right arm — the injured worker died two days later. !Safe work practices: !Train supervisors and safety committee members in hazard recognition. !Identify and guard all nip points. !Never reach into an unguarded nip point. OSHA Office of Training and Education 7

9. 8 While patrolling the hog fuel conveyor belt system, a worker noticed a piece of wire caught in the nip point between the hog fuel belt and the head spool. He reached into the nip-point area to remove the wire. As he grabbed the wire, his hand was pulled into the nip point. His arm was crushed when it rotated through the nip point and the head spool. The crushing injury resulted in the amputation of his right arm — the injured worker died two days later. Industry: Pulp & Paper Age: 26 years Experience: Several Years Area: Vancouver Island POSTER # 97-07

10. OSHA Office of Training and Education 9 Point of Operation That point where work is performed on the material, such as cutting, shaping, boring, or forming of stock must be guarded.

11. OSHA Office of Training and Education 10 Rotating Parts

12. OSHA Office of Training and Education 11 In-Running Nip Points Belt and pulley Chain and sprocket Rack and pinion Rotating cylinders

13. OSHA Office of Training and Education 12

14. OSHA Office of Training and Education 13

15. OSHA Office of Training and Education 14

16. Machine Guarding OSHA Office of Training and Education 15 3. What is a nip point? 4. What is point of operation?

17. !5.What are three requirements when gaurding a machine of tool OSHA Office of Training and Education 16

18. OSHA Office of Training and Education 17 Requirements for Safeguards !Prevent contact - prevent worker’s body or clothing from contacting hazardous moving parts !Secure - firmly secured to machine and not easily removed !Protect from falling objects - ensure that no objects can fall into moving parts !Create no new hazards - must not have shear points, jagged edges or unfinished surfaces !Create no interference - must not prevent worker from performing the job quickly and comfortably !Allow safe lubrication - if possible, be able to lubricate the machine without removing the safeguards

19. !5.What are three requirements when gaurding a machine of tool. OSHA Office of Training and Education 18

20. !6. list three methods of machine safeguarding. OSHA Office of Training and Education 19

21. OSHA Office of Training and Education 20 Methods of Machine Safeguarding !Guards >fixed >interlocked >adjustable >self-adjusting !Devices >presence sensing >pullback >restraint >safety controls (tripwire cable, two-hand contol, etc.) >gates ! Location/distance ! Feeding and ejection methods >automatic and/or semi- automatic feed and ejection >robots ! Miscellaneous aids >awareness barriers >protective shields >hand-feeding tools

22. !6. list three methods of machine safeguarding. OSHA Office of Training and Education 21

23. OSHA Office of Training and Education 22 Fixed Guard Provides a barrier - a permanent part of the machine, preferable to all other types of guards.

24. OSHA Office of Training and Education 23 Interlocked Guard When this type of guard is opened or removed, the tripping mechanism and/or power automatically shuts off or disengages, and the machine cannot cycle or be started until the guard is back in place. Interlocked guard on revolving drum

25. OSHA Office of Training and Education 24 Adjustable Guard Provides a barrier which may be adjusted to facilitate a variety of production operations. Bandsaw blade adjustable guard

26. OSHA Office of Training and Education 25 Self-Adjusting Guard Provides a barrier which moves according to the size of the stock entering the danger area. Circular table saw self-adjusting guard

27. !7.What machine in the shop has a self adjusting guard? OSHA Office of Training and Education 26

28. !8.Describe a pull back device. OSHA Office of Training and Education 27

29. OSHA Office of Training and Education 28 Pullback Device !Utilizes a series of cables attached to the operator’s hands, wrists, and/or arms !Primarily used on machines with stroking action !Allows access to the point of operation when the slide/ram is up !Withdraws hands when the slide/ram begins to descend

30. OSHA Office of Training and Education 29 Pullback Device (cont’d) !Hands in die, feeding !Point of operation exposed !Pullback device attached and properly adjusted ! Die closed ! Hands withdrawn from point of operation by pullback device

31. OSHA Office of Training and Education 30

32. !8.Describe a pull back device !9. Describe a restraint device. OSHA Office of Training and Education 31

33. OSHA Office of Training and Education 32 Restraint Device !Uses cables or straps attached to the operator’s hands and a fixed point !Must be adjusted to let the operator’s hands travel within a predetermined safe area !Hand-feeding tools are often necessary if the operation involves placing material into the danger area

34. !9. Describe a restraint device. !10. What is a trip wire? OSHA Office of Training and Education 33

35. OSHA Office of Training and Education 34 Safety Tripwire Cables !Device located around the perimeter of or near the danger area !Operator must be able to reach the cable to stop the machine

36. !10. What is a trip wire? OSHA Office of Training and Education 35

37. OSHA Office of Training and Education 36 Two-Hand Control. !Requires constant, concurrent pressure to activate the machine !The operator’s hands are required to be at a safe location (on control buttons) and at a safe distance from the danger area while the machine completes its closing cycle

38. OSHA Office of Training and Education 37 Gate !Movable barrier device which protects the operator at the point of operation before the machine cycle can be started !If the gate does not fully close, machine will not function Gate OpenGate Closed

39. OSHA Office of Training and Education 38 Safeguarding by Location/Distance !Locate the machine or its dangerous moving parts so that they are not accessible or do not present a hazard to a worker during normal operation !Maintain a safe distance from the danger area

40. OSHA Office of Training and Education 39 Automatic Feed (shown on power press) Transparent Enclosure Guard Stock Feed Roll Danger Area Completed Work

41. OSHA Office of Training and Education 40 Robots !Machines that load and unload stock, assemble parts, transfer objects, or perform other tasks !Best used in high- production processes requiring repeated routines where they prevent other hazards to employees

42. OSHA Office of Training and Education 41 Protective Shields These do not give complete protection from machine hazards, but do provide some protection from flying particles, splashing cutting oils, or coolants.

43. OSHA Office of Training and Education 42 Holding Tools !Used to place and remove stock in the danger area !Not to be used instead of other machine safeguards, but as a supplement

44. OSHA Office of Training and Education 43 Some Examples of OSHA Machine Guarding Requirements....

45. OSHA Office of Training and Education 44 Guarding Fan Blades When the periphery of the blades of a fan is less than 7 feet above the floor or working level, the blades must be guarded with a guard having openings no larger than 1/2 inch.

46. OSHA Office of Training and Education 45 Abrasive Wheel Machinery Work rests on offhand grinding machines must be kept adjusted closely to the wheel with a maximum opening of 1/8-inch to prevent the work from being jammed between the wheel and the rest, which may result in wheel breakage.

47. OSHA Office of Training and Education 46 Abrasive Wheel Machinery The distance between the wheel periphery and the adjustable tongue must never exceed 1/4-inch.

48. OSHA Office of Training and Education 47 Power-Transmission Apparatus Power-transmission apparatus (shafting, flywheels, pulleys, belts, chain drives, etc.) less than 7 feet from the floor or working platform must be guarded. Unguarded belt and pulley

49. OSHA Office of Training and Education 48 Machine Safety Responsibilities !Management >ensure all machinery is properly guarded !Supervisors >train employees on specific guard rules in their areas >ensure machine guards remain in place and are functional >immediately correct machine guard deficiencies !Employees >do not remove guards unless machine is locked and tagged >report machine guard problems to supervisors immediately >do not operate equipment unless guards are in place

50. OSHA Office of Training and Education 49 Training !Hazards associated with particular machines !How the safeguards provide protection and the hazards for which they are intended !How and why to use the safeguards !How and when safeguards can be removed and by whom !What to do if a safeguard is damaged, missing, or unable to provide adequate protection Operators should receive training on the following:

51. OSHA Office of Training and Education 50 Summary !Safeguards are essential for protecting workers from needless and preventable machinery- related injuries !The point of operation, as well as all parts of the machine that move while the machine is working, must be safeguarded !A good rule to remember is: Any machine part, function, or process which may cause injury must be safeguarded