1. Our Vision. Your Safety ™
Mobileye Setup Wizard
Version 5.9.1
User Manual
Our Vision. Your Safety ™

2. Mobileye Setup Wizard Activation
Click on the Mobileye Setup Wizard icon to open the application

3. Welcome Screen
Choose the preferred available language and Click “Next” to continue

4. User Identification and Accessories
Enter your Username & Password, then click on “Login”
Choose your “Installation site”
In the “Accessories” section you can:
Access the Vehicle Database
Update the Vehicle Database

5. Vehicle Database Vehicle Database Choose the relevant
“Car Manufacture”

6. Vehicle Database
Vehicle Database
Choose the relevant
“Car Model”

7. Vehicle Database After choosing the Car
Manufacture and Model you will get instructions were to find the CAN wires in the Vehicle, and what signals are available by
CAN-bus.
You will also get a picture
describing the CAN-bus wires location.

8. Vehicle Database Vehicle Database Choose “Accept selection”
for CAN-Bus configuration
to take effect.
Chose “Cancel selection”
to return to Analog
Installation

9. User Identification and Accessories
After selecting the wanted vehicle
profile you return to the Mobileye
Setup Wizard “User Identification
& Accessories” slide
The selected vehicle will appear in
all the following steps
Click “Next” to continue

10. Connection Phase Connect your Laptop to the Mobileye system using
the “EyeCAN” cable or
“Kvaser” cable
Connect E-box to Mobileye5
(if this is a Mobileye 5 analog installation)
Click on “Next” to initiate
connection

11. System Information
Please verify all relevant system information is shown and click “Next” to continue.
Click “Try again” if
Information fails to appear.
Click “Restore system defaults”
if you whish to reset the system
configurations (in case the system was
previously installed on a different vehicle)
Click on “Signal test & config ” to skip Calibration and
jump directly to Signal Test & configuration slide

12. System Information When installing a Mobileye 5
Enhancement–box (E-box)
When installing a Mobileye 5
system using the Mobileye
E-box make sure to:
Connect E-box to Mobileye system and confirm the E-box has been recognized (indicated by a V in the Enhancement–box check box).
Press “Next” to continue

13. Local Information Select your “Country”
Select the “Measurement system”
Select the “Speed format”
Select the “Road driving side”
Note:
Confirm “SLI detected locals” matches the speed sign type and the Speed unit (km/h or mph) of the selected Country
Click “Next” to continue

14. Local Information
Use the vertical grid lines to properly attach the camera to the windshield, verifying it is not rotated or tilted.
You can use the Red horizontal line if required. The Red line will appear only after inserting the camera height value.

15. Local Information Vehicle Information:
Enter the “Vehicle Chassis Num” (or license plate number)
Enter the vehicle Details (manufacture, model, year)
Car Information will show automatically if a profile was chosen from vehicle Database.
If vehicle details are not in Database, click on Other to add the vehicle details.

16. Click “Next” to continue
Local Information
Vehicle Measurements:
Enter the Camera height measurement (if not already entered)
Enter the “Distance to bumper” measurement
Enter the “Vehicle width” (Front wheel base)
Enter camera distance to left and right windshield edges
Click “Next” to continue

17. Car Hood Step
Use the cursor or the left hand side bar to locate the horizontal line at the car hood level (only if Car Hood is visible)
If there is no Car Hood, do not mark anything. Keep default Car hood value at -120)
Click “Next” to continue

18. Signals Sources – CAN-bus installations
If a vehicle profile was chosen from the “Vehicle Database”,
it is possible to switch the signals source back to Analog (Only for C2 series or Mobileye 5 with E-box)
If all signals are available by Vehicle CAN-bus there is no need to choose the Signals Polarity (Option is disabled)
Click “Next” to continue

19. Signals Sources – Analog installations
If connected to the vehicle’s Analog Speed Signal, enter the vss rate (vehicle Speed Signals)
Choose the polarity of the Analog signals (choose between High and Low
Choose Disabled if you did not connect to a specific signal
Click “Next” to continue

20. Camera Calibration Choose the preferred Calibration method:
TAC - you will continue to “Camera Calibration” slide
Automatic Calibration – all configuration will be burned to the system and you will proceed to “Signal test & and configuration” slide (or to the Alerts configuration slide, if permitted)

21. Click on “Calculate close TAC” TAC Calibration TAC - Calibration
Locate the “TAC Target” exactly in the middle of the vehicle’s front bumper.
For cars – close as possible to the front bumper.
For trucks – 1 meter away from front bumper.
Click on
“Calculate close TAC”

22. TAC Calibration
Close TAC Calibration
After clicking on Calculate Close TAC, you will see a black image for a few seconds.
When “Close TAC calculation” is completed, an image of the close
target with red dots will appear and A pop-up message will ask you to move the TAC to the Far Position

23. TAC Calibration Far TAC Calibration
Now, move the TAC Target to the Far position (1 meter away from the vehicle's front bumper) and only then:
click “OK” on the message box
click on “Calculate far TAC”
After clicking on Calculate Far TAC, you will see a black image for a few seconds.

24. TAC Calibration
After TAC calculation is complete, check the F.O.E and Camera height results according to the table below.
If all is OK, Click on “Burn Now”
Recommended Horizon values (FOE Y value) for different camera heights.
Note – FOE Y values may differ by +/- “10” from recommended values.

25. TAC Calibration
When Burning process is complete click “OK” in the pop up message
Click “Next” to continue

26. when changing any value
Alerts configuration
The Alerts Configuration screen enables users to define the system settings (sensitivity values) and disable the system control buttons so drivers cannot modify the system settings.
If you choose not to change any system settings. Simply click “Next” to continue.
Note:
when changing any value
You must burn the new
configurations
For more details download the full Alerts configuration - User Manual

27. Please pay attention to the instructions
Alerts configuration
Step 1 – check physical connection of all signals to the Mobileye system (either by CAN or analog).
- Signal is not detected by the system
- Signal detected by the system, but not activated.
- Signal detected and activated.
- Signal is disabled.
Please pay attention to the instructions

28. Signal Test and Configuration
Step 2 –
Activate and verify each signal.
If any signal fails the activation test, or connection verification test, click Restart test to test again.
All signals must pass the test (Green V icon) in order to complete the installation process

29. Signal Test and Configuration
Step 3 – Test drive
Drive and confirm speed indication in the Setup Wizard matches to the actual speed of the car.
After completing speed test,
Click “Next” button to finish the Calibration or enter the system into “Automatic Calibration” mode.
Note 1:
If speed doesn’t match the real vehicle speed, change the VSS rate, and click “Burn now” (this is optional only when Speed Signal source is Analog).

30. E-Box Outputs When E-Box is connected a
“E-Box out” button will appear.
Enhancement Box features:
2 additional independent configurable analog Outputs.
When IHC wire is not used for IHC, “IHC out” button will appear and will allow configuration of 1 analog output.

31. E-Box Outputs configuration
Choose the Alert Yype from the list and assign it to the relevant output by clicking Left or Right arrows.
Note:
Up to 3 Alert Types can be assigned to each output.
Note:
SLI Alert Type cannot be assigned with other Alert Types

32. E-Box Outputs configuration
Choose Alert Output Type:
Continuous
Output will be active for as long as the alert is active
Patterned
Output can be configured according to user demands.

33. E-Box Outputs configuration
If you choose Alert Output Type: “Patterned” Choose the output Duration
Effective – Output will be active for as long as the Alert is active (On/Off) Or
Choose to limit the Output
Duration by choosing any of the time options in the list.
Using the options you can configure the output pattern duration (in milliseconds)
Use the “duplicate” button to copy the Alert Type to the second output option.
Use the “move” button to move the Alert Type to the second output option.

34. E-Box Outputs configuration
After E-Box configuration is complete press “Burn now” to burn the new outputs settings

35. Fix Speed What is Fix Speed:
OBD II universal Speed signal acquisition (Speed by Request from OBD2 CAN-bus) without having to perform CAN sniffing.
Works only when connected to the OBDII CAN-bus on a bus speed of 250kbs or 500kbs (and only Pins 6 & 14 in OBDII)
Can be used when a vehicle has been chosen from the DB and the speed signal is not accurate or not working.
Will not affect other signals receiving from the OBDII CAN-Bus.

36. Thank you for using Mobileye Setup Wizard Application.
Finish
Thank you for using Mobileye Setup Wizard Application.
Please click on “Finish” to exit.

37. Thank you, and please drive safely