1. © 2011 Autodesk Mechanical Simulation in AutoCAD ® 2012 Craig A. Miller – Pennsylvania College of Technology CAD Technology Specialist

2. © 2011 Autodesk Class Summary Creating, Manipulating & Animating AutoCAD Assemblies  Quick Review of Parametric Constraints in AutoCAD  Creating 3D Block Parts  Use Geometric Constraints to Assemble Block Parts  Use Parametric Dimensions to Edit Component Positions  Writing Simple LISP Routines to Animate Assemblies

3. © 2011 Autodesk Learning Objectives At the end of this class, you will be able to:  Create 3D block parts with connection geometry  Use geometric constraints to create mechanical assemblies  Apply parametric dimensions to assemblies to edit component position  Create a “skeleton frame” that is suitable for assembling blocks  Drive motion within an assembly through the use of simple LISP routines

4. © 2011 Autodesk Instructor Introduction  Craig A. Miller - CAD Technology Specialist  Pennsylvania College of Technology

5. © 2011 Autodesk Instructor Introduction  Craig A. Miller - CAD Technology Specialist  Pennsylvania College of Technology  E-mail Address - cmiller2@pct.edu

6. © 2011 Autodesk Instructor Introduction  Craig A. Miller - CAD Technology Specialist  Pennsylvania College of Technology  E-mail Address - cmiller2@pct.edu  Using AutoCAD since Release 11

7. © 2011 Autodesk Instructor Introduction  Craig A. Miller - CAD Technology Specialist  Pennsylvania College of Technology  E-mail Address - cmiller2@pct.edu  Using AutoCAD since Release 11  Started with Inventor on Release 1

8. © 2011 Autodesk Instructor Introduction  Craig A. Miller - CAD Technology Specialist  Pennsylvania College of Technology  E-mail Address - cmiller2@pct.edu  Using AutoCAD since Release 11  Started with Inventor on Release 1  CAD experience with Software that will remain nameless

9. © 2011 Autodesk Instructor Introduction  Craig A. Miller - CAD Technology Specialist  Pennsylvania College of Technology  E-mail Address - cmiller2@pct.edu  Using AutoCAD since Release 11  Started with Inventor on Release 1  CAD experience with Software that will remain nameless  Personal Note - I’m an avid runner  Lots of time to think about new ways to use AutoCAD

10. © 2011 Autodesk Rules for Assigning 2D Constraints to 3D Objects 1. Geometric Constraints can only be applied in the XY Plane

11. © 2011 Autodesk Rules for Assigning 2D Constraints to 3D Objects 1. Geometric Constraints can only be applied in the XY Plane 2. Objects to which Constraints are being applied must be Co- Planer

12. © 2011 Autodesk Rules for Assigning 2D Constraints to 3D Objects 1. Geometric Constraints can only be applied in the XY Plane 2. Objects to which Constraints are being applied must be Co- Planer 3. Multiple Constraints cannot be applied to single 3D Objects in more then one plane.

13. © 2011 Autodesk Rules for Assigning Parametric Dimensions to 3D Objects 1. Parametric Dimensions can only be applied in the XY Plane

14. © 2011 Autodesk Rules for Assigning Parametric Dimensions to 3D Objects 1. Parametric Dimensions can only be applied in the XY Plane 2. Objects to which Parametric Dimensions are being applied must be Co-Planer

15. © 2011 Autodesk Rules for Assigning Parametric Dimensions to 3D Objects 1. Parametric Dimensions can only be applied in the XY Plane 2. Objects to which Parametric Dimensions are being applied must be Co-Planer 3. Multiple Parametric Dimensions cannot be applied to single 3D Objects in more then one plane.

16. © 2011 Autodesk Creating a Skeleton Frame What is a Skeleton Frame 1. Line, arc, circle geometry etc. that is fixed to accommodate constraints with 3D Solid Model Parts. 2. DO NOT turn your Skeleton Frames into Blocks.

17. © 2011 Autodesk Questions

18. © 2011 Autodesk Autodesk University Session Feedback Your feedback is very important to Autodesk Attendees can complete session survey on their mobile device, PC or at a survey station Each session survey completed will be entered for a daily drawing for a free AU 2012 pass. You can help make AU 2012 better! Complete the AU Conference Survey at a survey station and receive an AU 2011 T-Shirt

19. © 2011 Autodesk Craig A. Miller cmiller2@pct.edu Thank You! cmiller2@pct.edu

20. © 2011 Autodesk Autodesk, AutoCAD* [*if/when mentioned in the pertinent material, followed by an alphabetical list of all other trademarks mentioned in the material] are registered trademarks or trademarks of Autodesk, Inc., and/or its subsidiaries and/or affiliates in the USA and/or other countries. All other brand names, product names, or trademarks belong to their respective holders. Autodesk reserves the right to alter product and services offerings, and specifications and pricing at any time without notice, and is not responsible for typographical or graphical errors that may appear in this document. © 2011 Autodesk, Inc. All rights reserved.