1. 1 ERT 207 Analytical Chemistry ERT 207 ANALYTICAL CHEMISTRY ALINA RAHAYU MOHAMED School of Bioprocess Engineering University Malaysia Perlis 02600, Kangar Perlis email: alina@unimap.edu.myalina@unimap.edu.my

2. 2 ERT 207 Analytical Chemistry LECTURE 2 11th July 2008

3. 3 ERT 207 Analytical Chemistry 1.3 STEPS IN QUANTITATIVE ANALYSIS 1.Define the Problem 3.Obtain a Representative Sample 2.Select a Method

4. 4 ERT 207 Analytical Chemistry STEPS IN QUANTITATIVE ANALYSIS (continue) 4.Prepare the sample for analysis 6. Perform the Measurement 5.Perform Any Necessary Chemical Separations

5. 5 ERT 207 Analytical Chemistry STEPS IN QUANTITATIVE ANALYSIS (continue) 7. Calculate the Results and Report

6. 6 ERT 207 Analytical Chemistry 1. Define the Problem Before we begin defining the problem for an analysis procedure, we must have some information; A)Who is the client(EPA, engineers) B)The purpose of analysis C)What type of sample to be analyzed

7. 7 ERT 207 Analytical Chemistry 1. Define the Problem Factors to consider:  What is the problem—what needs to be found?  Qualitative and/or quantitative?  What will the information be used for? Who will use it?  When will it be needed?  How accurate and precise does it have to be?  What is the budget?

8. 8 ERT 207 Analytical Chemistry Once the problem is defined, next questions: A) how sample is to be obtained B) how much is needed C)What separations may be required to eliminate interferences?

9. 9 ERT 207 Analytical Chemistry How to select a Method?

10. 10 ERT 207 Analytical Chemistry 2.Select a Method Factors to be considered:  Sample type  Size of sample  Sample preparation needed  Concentration and range (sensitivity needed)  Selectivity needed (interferences)  Accuracy/precision needed  Tools/instruments available  Cost  Are methods available in the chemical literature?  Are standard methods available?

11. 11 ERT 207 Analytical Chemistry 3.Obtain a Representative Sample Factors Sample type/homogeneity/size Sampling statistics/errors

12. 12 ERT 207 Analytical Chemistry The gross sample must be reduced in size to obtain a laboratory sample of several grams, from which a few grams to miligrams will be taken to be analyzed.

13. 13 ERT 207 Analytical Chemistry Sampling Obtaining a representative sample is the first step of an analysis. The gross sample is several small portions of the sample. This is reduced to provide a laboratory sample. An aliquot of this sample is taken for the analysis sample. Obtaining a representative sample is the first step of an analysis. The gross sample is several small portions of the sample. This is reduced to provide a laboratory sample. An aliquot of this sample is taken for the analysis sample.

14. 14 ERT 207 Analytical Chemistry Some precautions should be taken during handling and storing samples to prevent or minimize contamination, loss, decomposition or matrix change. We must prevent contamination or alteration of the sample by (1)light (2)atmosphere (3) container.

15. 15 ERT 207 Analytical Chemistry For example, some samples have to be protected from the atmosphere or light. It maybe an alkaline substance that will react with CO 2 in the air. Blood samples to be analyzed for CO 2 content shlould be protected from the atmosphere.

16. 16 ERT 207 Analytical Chemistry Next example, corrosive sample may react with the container. In automobile exhaust SO 2 is lost by dissolving in condensed water vapour from the exhaust.

17. 17 ERT 207 Analytical Chemistry 4.Prepare the Sample for Analysis Factors Solid, liquid, or gas? Dissolve? Ash or digest? Chemical separation or masking of interferences needed? Need to concentrate the analyte? Need to change (derivatize) the analyte for detection? Need to adjust solution conditions (pH, add reagents)?

18. 18 ERT 207 Analytical Chemistry 4.Prepare the Sample for Analysis Step 1: Measure the amount being analyzed (volume or weight of the sample) Replicate samples are taken for analysis Why?

19. 19 ERT 207 Analytical Chemistry 1) to obatin statistical data on the precision of the analysis 2) to provide more reliable results.

20. 20 ERT 207 Analytical Chemistry Step 2: Sample pretreatment Example: The organic materials sample are analyzed for inorganic constituents. The organic constituents maybe destroyed by dry ashing. How?

21. 21 ERT 207 Analytical Chemistry The organic materials is slowly combusted in a furnace at 400 o C to 700 o C. Organic materials escape out, leaving behind an inorganic residue which is soluble in dilute acid. Aim of step 2: to remove unwanted constituents that make up the whole sample.

22. 22 ERT 207 Analytical Chemistry Step 3: Optimizing sample condition Aim of step 3: to prepare sample for the next stage of analysis (The separation or measurement step) The solution condition is optimized. How?

23. 23 ERT 207 Analytical Chemistry For example, the pH may have to be adjusted or reagent is added to mask interference from other constituents. The analyte may have to be reacted with a reagent to convert it to a form suitable for measurement or separation. For example, a coloured product maybe formed that will be measured by spectrometry.

24. 24 ERT 207 Analytical Chemistry Distillation Precipitation Solvent extraction Solid phase extraction Chromatography (may be done as part of the measurement step) 5.Perform Any Necessary Chemical Separations

25. 25 ERT 207 Analytical Chemistry 5.Perform Any Necessary Chemical Separations Why conduct chemical separation? 1.to eliminate interference 2.to provide suitable selectivity in the measurement 3. to preconcentrate the analyte for more sensitive or accurate measurement

26. 26 ERT 207 Analytical Chemistry 6. Perform the Measurement Factors Calibration Validation/controls/blanks Replicates

27. 27 ERT 207 Analytical Chemistry 6. Perform the Measurement Methods of carrying out the measurements: 1.gravimetric analysis 2.volumetric analysis 3. instrumental analysis. What are these?

28. 28 ERT 207 Analytical Chemistry Statistical analysis (reliability) Report results with limitations/accuracy information 7. Calculate the Results and Report

29. 29 ERT 207 Analytical Chemistry Tutorial Question 1 Close all of your notes! Will be discussed on Tuesday (15th July 2008) for G8-G13 at DJH room from 12- 2pm. Also, on 22nd July 2008, same place for G1-G7.

30. 30 ERT 207 Analytical Chemistry Basic tools in Analytical Chemistry

31. 31 ERT 207 Analytical Chemistry Modern balances are electronic. They still compare one mass against another since they are calibrated with a known mass. Common balances are sensitive to 0.1 mg. Fig. 2.1. Electronic analytical balance.

32. 32 ERT 207 Analytical Chemistry Fig. 2.8. Volumetric flask. Volumetric flasks are calibrated to contain an accurate volume. See the inside back cover of the text for tolerances of Class A volumetric glassware.

33. 33 ERT 207 Analytical Chemistry Fig. 2.9. Transfer or volumetric pipets. Volumetric pipets accurately deliver a fixed volume. A small volume remains in the tip. Volumetric pipets accurately deliver a fixed volume. A small volume remains in the tip.

34. 34 ERT 207 Analytical Chemistry Fig. 2.10. Measuring pipets. Measuring pipets are straight-bore pipets marked at different volumes. They are less accurate than volumetric pipets. Measuring pipets are straight-bore pipets marked at different volumes. They are less accurate than volumetric pipets.

35. 35 ERT 207 Analytical Chemistry Fig. 2.11. Hamilton microliter syringe. Syringe pipets precisely deliver microliter volumes. They are commonly used to introduce samples into a gas chromatograph. Syringe pipets precisely deliver microliter volumes. They are commonly used to introduce samples into a gas chromatograph.

36. 36 ERT 207 Analytical Chemistry Fig. 2.12 Single-channel and multichannel digital displacement pipets and microwell plates. These syringe pipets can reproducibly deliver a selected volume. They come in fixed and variable volumes. The plastic tips are disposable. These syringe pipets can reproducibly deliver a selected volume. They come in fixed and variable volumes. The plastic tips are disposable.

37. 37 ERT 207 Analytical Chemistry Fig. 2.14. Meniscus illuminator. Position the black field just below the meniscus. Avoid parallax error by reading at eye level. Position the black field just below the meniscus. Avoid parallax error by reading at eye level.

38. 38 ERT 207 Analytical Chemistry Fig. 2.20. Wash botltles: (a) polyethylene, squeeze type; (b) glass, blow type. Use these for quantitative transfer of precipitates and solutions, and for washing precipitates. Use these for quantitative transfer of precipitates and solutions, and for washing precipitates.

39. 39 ERT 207 Analytical Chemistry Next topic: Basic statistics

40. 40 ERT 207 Analytical Chemistry Thank you Q& A session.