1. Your Connectivity Partner

2. Locations Main Office: High Tech Products Lallio, Italy USA Office: HTP Connectivity Parsippany, NJ

3. Locations Manufacturing: HTP CHINA LTD Guangdon Province, China

4. DIN 43650 Moulded Assemblies & Connectors

5. DIN 43650 Typically used to electrically connect hydraulic & pneumatic solenoids, filter & pressure switches and sensors This connector group is used by the majority of valve manufacturers

6. DIN 43650 Molded Assemblies Saves installation time and expense Available in any length, in all 5 DIN 43650 types With or without light indication and surge suppression For 24, 110 & 220 volt applications

7. DIN 43650 Connectors Provides a greater range of connectors then offered by the valve manufacturers Circuits available include – Without components – LED Only – Varistor & LED – Diode & LED For 24, 110 & 220 volt applications

8. M12 to DIN 43650 Typically used to connect solenoid valves or sensors to distribution boxes All DIN 43650 types available With or without LED and Suppression.5 Meter standard cable length (other lengths available upon request)

9. DIN Double Y Cable Used to double the outputs from a Distribution Box Available in all the DIN43650 Connector Types With or without LED & Suppression

10. DIN Triple Y Cable Used to provide multiple outputs from a single M12 connector Available in all the DIN43650 Connector Types With or without LED & Suppression

11. Multiple Connector Assemblies Up to 10 connectors with 1 cable One individual to each connector Common negatives and grounds (on 2 position)

12. DIN 43650 to M12 Connector Allows connection to a DIN43650A or DIN43650B valve with an M12 Connector Available also with different circuit

13. New Big DIN 43650A Separate circuit board allow larger components to be used

14. DIN Male Panel Mount (Basis) Male DIN43650 connectors For panel and special mounting

15. Special Industrial Connector 15mm X 15mm with 4 diagonal pins

16. DIN Extension Cables Female to Male Connections Allows DIN43650 Cable to be Extended Available in all DIN Types

17. In Line Cycle Timer – Now Available The HTP in-line timer is designed to cycle power on and off, to either pneumatic or hydraulic solenoid valves. Typical applications include draining water from compressor tanks, periodic product sampling, and control of lubricating or irrigation systems. Plugs in-line between male & female connectors Works with any voltage from 24 to 240 VAC/DC ON – 0.5 to 10 sec OFF – 0.5 to 45 min For pneumatic or hydraulic solenoid valves ON and OFF LED status indication Manual push button override

18. New Products – Now Available Industrial Form B Molded Assemblies with Dual Ground Pins Works with both ground down and ground up cable positions

19. M12 Connectors and Molded Assemblies

20. M12 Connector Wiring 3 Pole Versions – 1 = Positive – 3 = Negative – 4 = Signal 4 Pole Versions – 1 = Positive – 3 = Negative – 2 = Signal 1 – 4 = Signal 2 5 Pole Versions – 1 = Positive – 3 = Negative – 2 = Signal 1 – 4 = Signal 2 – 5 = Ground M12 Connectors are a very popular way to connect sensors & switches. Changing a sensor or switch is much faster when a connector is used, reducing down time and labor expense.

21. M12 Connector Assemblies 3, 4, 5, 8 or 12 pole versions Male or female Straight or right angle Single or Double Ended PVC, Shielded or PUR cable (other cable available on request) Standard Length 3 meters (1meter for double ended) 2 or 3 LED’s for PNP or NPN switch indication NEW – Fully Shielded Versions Available

22. M12 “T” Connectors “T” connectors are designed to expand the ports on hard wired distribution boxes, by splitting the two individual wires into two connectors NEW – Transparent “T” With Light Indication

23. M12 Y Cable Can be used to double the capacity of an M12 Distribution Box, by splitting the individual inputs

24. M12 Triple Y Cable Used to provide multiple outputs from a single M12 connector

25. M12 Field Wire Connectors 4, 5, or 8 pole versions Screw terminals Straight or right angle Single or dual cable entry

26. M12 Field Wire Connectors NEW!! 12 pole versions

27. Metal Field Wire M12 Connector Housing in Nickel Plated Brass For Tough Environments Rated IP 67 Completely Shielded

28. M12 Panel Mount Connectors 4, 5, 8 or 12 pole versions Female or male connectors Front or back mounting Solder or PCB connections or pre-wired

29. M8 Connectors and Assemblies

30. M8 Connector Wiring 3 Pole Versions – 1 = Positive – 3 = Negative – 4 = Signal 4 Pole Versions – 1 = Positive – 3 = Negative – 2 = Signal 1 – 4 = Signal 2 M8 Connectors are a very popular way to connect sensors & switches. Changing a sensor or switch is much faster when a connector is used, reducing down time and labor expense.

31. M8 Connector Assemblies 3 or 4 pole versions Male or female Straight or right angle Single or Double Ended PVC, Shielded or PUR cable Standard Length 3 meters (1meter for double ended) 2 LED’s for PNP or NPN switch indication NEW – Fully Shielded Versions Available

32. M8 “Y” Assemblies Both the “Y” assemblies are designed to expand the ports on hard wired distribution boxes, by splitting the two individual wires into two connectors

33. M8 Field Wire Connectors 3 or 4 pole versions Solder or screw terminals Straight

34. M8 Panel Mount Connectors 3 or 4 pole versions Female or male connectors Front mounting Solder or PCB connections or pre-wired

35. M12 Distribution Boxes

36. Distribution Boxes Distribution Boxes eliminate the need to run multiple cables back to the control panel and create a “plug and play” system They can be used for both input & output devices Commons within the box reduces wiring time at the control panel Distribution Boxes are designed around the standard wiring used for the connectors. Common wiring (to each connector position) is provided for positive, negative and ground positions. Each connector has 2 individual wires available to transfer NO & NC position status for input devices or one wire can be used to provide separate power for output devices

37. M12 Distribution Boxes – Field Wire 5 pole M12 connector 4, 6 or 8 ports Self wire or molded main cable With or without LED indication for PNP or NPN sensors

38. M12 Distribution Boxes – Triple signal 5 pole M12 connector 4 or 8 ports Self wire or molded main cable Without LED indication for PNP or NPN sensors

39. M12 Distribution Boxes – Molded Cable 5 pole M12 connector 4, 6 or 8 ports Molded main cable in 5, 10 or 15 meters With or without LED indication for PNP or NPN sensors

40. Magnetic Sensors For use with aluminum cylinders with target magnetic Available in dry contact (reed switches) or solid state (PNP or NPN) With many different mounting and body styles With molded cable, M12 or M8 connection

41. New Products – Now Available 7/8 “MINI CHANGE” – 3, 4 and 5 poles

42. New Products – Now Available 7/8 “MINI CHANGE” male / female 3, 4 and 5 poles Fieldwire connectors

43. New Products – Now Available 7/8 “MINI CHANGE” male / female 3, 4 and 5 poles Molded cable

44. New Products – Now Available 7/8 “MINI CHANGE” male / female 3, 4 and 5 poles Panel mount

45. New Product – now available 7/8 “MINI CHANGE” male / female 3, 4 and 5 poles T-splitter

46. New Products – Now Available M8 Distribution Boxes 6 – 8 – 10 Positions Terminal Blocks

47. New Products – Now Available M8 Distribution Boxes 6 – 8 – 10 – 12 Positions Molded cable

48. New Products – Now Available M8 Distribution Boxes 6 – 12 Positions M12 with 8 pole connector

49. New Products in Development M16 & M23 Connectors and Assemblies

50. Thank-you!