2. Scout Pro Training

3. Introducing the Scout Pro Portable Balance: 7 Models From 200g x 0.01g to 6000g x 1g 5 Application Modes Optional USB or RS232 Interface Accessory w/cable Density/Specific Gravity Determination with Below Balance Hook Battery or AC Power (Power Pack Included) Integral Security Bracket Programmable Energy Saving Auto Shut-off The Ohaus Scout Pro

4. Unpack & Setup Shipping lock Secures load cell Battery Installation 4 AA batteries provide 40 hours of operation

5. Unpack & Setup AC plug Security bracket

6. Unpack & Setup USB Accessory RS232 Accessory

7. Unpack & Setup Rotate square pans counter clockwise Insert round pans

8. Operation Turn balance on Scout Pro is shipped ready to operate in all available weighing units, parts counting and percent weighing PRINT Unit 0.00g ON/ZERO Off Short press to print. Long press to switch weighing unit. 0.00g ON/ZERO Off PRINT Unit

9. Operation Hold Off until “OFF” is displayed, then release to turn off. ON/ZERO Off PRINT Unit OFF Weigh in any unit

10. Menus and Calibration With balance off, hold ON/ZERO until MENU is displayed MENU ON/ZERO Off PRINT Unit Release ON/ZERO to enter the menu C.A.L. ON/ZERO Off PRINT Unit C.A.L.S.E.t.U.P.U.n.I.t.E.n.d.

11. Menu System C.A.L. Calibration gkgozlbPC - Count - Cnt. Enh - Off %End PRINT Unit PRINT Unit PRINT Unit Auto-Off Linearity cal Mode - Display Hold - Totalize - Off End S.E.t.U.P. U.n.I.t. E.n.d. PRINT Unit

12. Calibration Access calibration C.A.L. ON/ZERO Off - C - C 2 0 0 g Add cal weight ON/ZERO Off - C - d o n E

13. Parts Counting & Parts Counting Setup Mode: Parts Counting This mode allows the user to count based on the average weight of an original reference sample This mode is enabled by setting “PC” to “Count” in the “.U.n.i.t.” part of the menu To set-up mode: Enter Menu Mode, press PRINT/Unit to go to “.U.n.i.t.” and then press ON/ZERO/Off Press PRINT/Unit to go to “UnitS PC” and then press ON/ZERO/Off Press PRINT/Unit to go to “Count” and then press ON/ZERO/Off Press PRINT/Unit to go to “End” and then press ON/ZERO/Off Press PRINT/Unit to go to “.E.n.d.” and then press ON/ZERO/Off Sample Sizes -- The Scout Pro allows the user to change the sample size with a press of the Print/Unit key

14. Mode: Enhanced Parts Counting APW Enhancement -- The Scout Pro allows the user to turn-on automatic recalculation of the average piece weight (APW Optimization) -- this is the same function as found in Trooper Count and Ranger Count Without Optimization, the APW is the average of the weight of the sample, divided by the number of pieces in the sample -- if the user needs a sample of 100, they have to count by hand 100 pieces! With Optimization, the APW is the average of the weight of the initial sample as well as any subsequent samples -- the user can reach a sample of 100 by adding parts on the pan 10 at a time, increasing accuracy! Enhanced Parts Counting

15. Mode: Enhanced Parts Counting This mode is enabled by setting “PC” to “Cnt.Enh” in the “.U.n.i.t.” part of the menu To set-up mode: Enter Menu Mode, press PRINT/Unit to go to “.U.n.i.t.” and then press ON/ZERO/Off Press PRINT/Unit to go to “UnitS PC” and then press ON/ZERO/Off Press PRINT/Unit to go to “Cnt.Enh” and then press ON/ZERO/Off Press PRINT/Unit to go to “End” and then press ON/ZERO/Off Press PRINT/Unit to go to “.E.n.d.” and then press ON/ZERO/Off Sample Sizes -- The Scout Pro allows the user to change the sample size with a press of the Print/Unit key Enhanced Parts Counting Setup

16. Parts Counting Operation CLr.APu ON/ZERO Off Put 5 PC PRINT Unit PRINT Unit 5 PC Place a container Press and hold PRINT/Unit key until “PC” is indicated Display will then show “Clr.APu” Press Print/Units to use the average piece (APW) stored in memory (if there is one) To re-establish a new APW, press On/Zero/Off once Scout Pro will display “Put 10”. To select a different sample size, press Print/Unit Place displayed number of pieces in container and press ON/ZERO/Off Scout Pro will calculate APW and display total count To reset APW, press Print/Unit until “PC” is displayed again 0. 0 0 g ON/ZERO Off

17. Mode: Percent Weighing This mode allows the user to display the weight of a sample as a percentage of a reference weight The reference weight is placed on the pan first, and equals 100% Each reference weight will be a percentage from 0.1% to 99,999.9%, depending on the Capacity X Readability of the scale -- most users will use 1.0% to 200.0% at the most Applications: Formulation and compounding, weight checking Percent Weighing %

18. Percent Weighing % Setup Mode: Percent Weighing This mode is enabled by setting “%” to “On” in the “.U.n.i.t.” part of the menu To set-up mode: Enter Menu Mode, press PRINT/Unit to go to “.U.n.i.t.” and then press ON/ZERO/Off Press PRINT/Unit to go to “UnitS %” and then press ON/ZERO/Off Press PRINT/Unit to go to “On %” and then press ON/ZERO/Off Press PRINT/Unit to go to “End” and then press ON/ZERO/Off Press PRINT/Unit to go to “.E.n.d.” and then press ON/ZERO/Off

19. Percent Operation Press and hold Print/Unit key until “%” is indicated Display will then show “Clr.Ref” Press Print/Units to use target weight in memory (if there is one) To enter a new target weight, press On/Zero/Off once Scout Pro will display “Put.rEF” Place target weight on pan, press On/Zero/Off again -- Scout Pro will display target weight value Press On/Zero/Off again -- Scout Pro will display 100% To reset target weight, press Print/Unit until “%” is displayed again CLr.rEF ON/ZERO Off PutrEF % % PRINT Unit PRINT Unit ON/ZERO Off 123.45 g ON/ZERO Off 1 0 0 % 2 5 %

20. Mode: Display Hold This mode allows the user to hold the highest stable weight on the display until manually cleared Display Hold can work with any weighing unit or mode -- including % or parts counting -- except Totalization The Scout Pro will show the current measurement on the pan with a flashing stability indicator “*” Applications: Postal and shipping 0.00  Display Hold

21. Mode: Display Hold This mode is enabled by selecting “HoLd” in the “MOde” part of the “S.E.t.U.P” menu To set-up mode: Enter Menu Mode, press PRINT/Unit to go to “ S.E.t.U.P ” and then press ON/ZERO/Off Press PRINT/Unit to go to “MOdE” and then press ON/ZERO/Off Press PRINT/Unit to go to “HoLd” and then press ON/ZERO/Off Press PRINT/Unit to go to “End” and then press ON/ZERO/Off Press PRINT/Unit to go to “.E.n.d.” and then press ON/ZERO/Off 0.00  Display Hold Display Hold Setup

22. Display Hold Operation Hold PRINT Unit  123.45 g ON/ZERO Off HLd.OFF To Use Mode: Press PRINT/Unit once to start Display Hold “HoLd” will be displayed briefly indicating Display Hold is active Place weight on pan “ * ” will flash indicating highest stable weight value will be held Take weight of pan The display will change and then display the Hold value with the flashing “ * ” To Clear Display press On/Zero/Off To Exit Mode hold ON/ZERO/Off until “HLdOFF” is displayed  123.45 g 0.00  Display Hold

23. Mode: Totalization This mode allows the user to sum a series of weights -- up to the limit of the display (999,999) Totalization can work with any weighing unit or mode -- including % or parts counting -- except Display Hold Once you are in Totalization, you cannot change weighing units/modes without exiting Totalization The Scout Pro will show the current measurement on the pan with a solid “t”, and then the total as a flashing “t” Applications: Formulation and compounding, parts kitting Σ Totalization

24. Mode: Totalization This mode is enabled by selecting “totAL” in the “MOde” part of the “S.E.t.U.P” menu To set-up mode: Enter Menu Mode, press PRINT/Unit to go to “ S.E.t.U.P ” and then press ON/ZERO/Off Press PRINT/Unit to go to “MOdE” and then press ON/ZERO/Off Press PRINT/Unit to go to “totAL” and then press ON/ZERO/Off Press PRINT/Unit to go to “End” and then press ON/ZERO/Off Press PRINT/Unit to go to “.E.n.d.” and then press ON/ZERO/Off Σ Totalization Totalization Setup

25. Totalization Operation Press PRINT/Unit once to start Totalization “totAL” will be displayed briefly and “t” will be displayed indicating Totalization is active Place a sample on the pan and press PRINT/Unit to enter the weight into memory “t” will flash indicating total weight. Remove the sample. “t” will stop flashing and the balance will return to zero Repeat the procedure with another sample and read the totalized weight To exit Totalization, hold down ON/ZERO until “tot.OFF” is displayed t o t A L PRINT Unit 0.00 g t ON/ZERO Off tot.OFF 123.45 g t PRINT Unit PREPARATION: 2 plastic cups, different colored water samples. Tare an empty cup Σ Totalization 0.00 g t

26. The Ohaus Scout Pro Scout Pro USP’s Mechanical overload and shock load protection Protects weighing cell 4 times better than Scout II Simple 2-button operation – 5 applications and 7 weighing units Optional USB or RS232 interfaces, simply insert the module; cable included