Download presentation
Presentation is loading. Please wait.
Published byNaomi McBride Modified over 9 years ago
1
Introduction to Electromechanical Energy Conversion
Chapter 1 Introduction to Electromechanical Energy Conversion 4/22/2017 Dr Awang Jusoh/Dr Makbul
2
Dr Awang Jusoh/Dr Makbul
1.1 Magnetic Circuits 4/22/2017 Dr Awang Jusoh/Dr Makbul
3
Magnetic Field Concept
Magnetic Fields: Magnetic fields are the fundamental mechanism by which energy is converted (transferred) from one form to another in electrical machines. Magnetic Material Definition : A material that has potential to attract other materials toward it, materials such as iron, cobalt, nickel Function: Act as a medium to shape and direct the magnetic field in the energy conversion process 4/22/2017 Dr Awang Jusoh/Dr Makbul
4
Magnetic Field Concept
Magnetic field around a bar magnet Two “poles” dictated by direction of the field Opposite poles attract (aligned magnetic field) Same poles repel (opposing magnetic field) 4/22/2017 Dr Awang Jusoh/Dr Makbul
5
Magnetic Field Concept
Magnetic Flux/ Flux Line Characteristic 1. Outside - Leaves the north pole (N) and enters the south pole (S) of a magnet. Inside - Leaves the south pole (S) and enters the north pole (N) of a magnet. 2. Like (NN, SS) magnetic poles repel each other. 3. Unlike (NS) magnetic poles attracts each other. 4. Magnetic lines of force (flux) are always continuous (closed) loops, and try to make as shortest distance loop. 5. Flux line never cross each others 4/22/2017 Dr Awang Jusoh/Dr Makbul
6
Magnetic Field Concept
4/22/2017 Dr Awang Jusoh/Dr Makbul
7
Machines Basic Requirements
Presence of a “magnetic fields” can be produced by: Use of permanent magnets Use of electromagnets Then one of the following method is needed: Motion to produce electric current (generator) Electric current to produce motion (motor) 4/22/2017 Dr Awang Jusoh/Dr Makbul
8
Dr Awang Jusoh/Dr Makbul
Ampere’s Law Any current carrying wire will produce magnetic field around itself. Magnetic field around a wire: Thumb indicates direction of current flow Finger curl indicates the direction of field 4/22/2017 Dr Awang Jusoh/Dr Makbul
9
Dr Awang Jusoh/Dr Makbul
Ampere’s Law Ampere’s law: the line integral of magnetic field intensity around a closed path is equal to the sum of the currents flowing through the surface bounded by the path H I1 I2 q dl Recall that the vector dot product is given by in which q is the angle between H and dl. 4/22/2017 Dr Awang Jusoh/Dr Makbul
10
Dr Awang Jusoh/Dr Makbul
Ampere’s Law If the magnetic intensity has constant magnitude and points in the same direction as the incremental length dl everywhere along the path, Ampere’s law reduces to in which l is the length of the path. Examples of such cases: (i) Magnetic field around a long straight wire, (ii) Solenoid 4/22/2017 Dr Awang Jusoh/Dr Makbul
11
Dr Awang Jusoh/Dr Makbul
Example 1: ( a long straight Wire) Example 2: (Solenoid) 4/22/2017 Dr Awang Jusoh/Dr Makbul
12
Dr Awang Jusoh/Dr Makbul
Flux Density Number of lines of magnetic force (flux) passing through unit area or Wb/m2 4/22/2017 Dr Awang Jusoh/Dr Makbul
13
Dr Awang Jusoh/Dr Makbul
Field Intensity The effort made by the current in the wire to setup a magnetic field. Magnetomotive force (mmf) per unit length is known as the “magnetizing force” H Magnetizing force and flux density related by: 4/22/2017 Dr Awang Jusoh/Dr Makbul
14
Dr Awang Jusoh/Dr Makbul
Permeability Permeability is a measure of the ease by which a magnetic flux can pass through a material (Wb/Am). The higher the better flux can flow in the magnetic materials. Permeability of free space o = 4 x 10-7 (Wb/Am) Relative permeability, r : 4/22/2017 Dr Awang Jusoh/Dr Makbul
15
Dr Awang Jusoh/Dr Makbul
Reluctance Reluctance, which is similar to resistance, is the opposition to the establishment of a magnetic field, i.e." resistance” to flow of magnetic flux. Depends on length of magnetic path , cross-section area A and permeability of material . 4/22/2017 Dr Awang Jusoh/Dr Makbul
16
Dr Awang Jusoh/Dr Makbul
Magnetomotive Force The product of the number of turns and the current in the wire wrapped around the core’s arm. (The ability of a coil to produce flux) N 4/22/2017 Dr Awang Jusoh/Dr Makbul
17
Dr Awang Jusoh/Dr Makbul
Magnetomotive Force The MMF is generated by the coil Strength related to number of turns and current, Symbol F, measured in Ampere turns (At) 4/22/2017 Dr Awang Jusoh/Dr Makbul
18
Dr Awang Jusoh/Dr Makbul
Magnetization Curve Behavior of flux density compared with magnetic field strength, if magnetic intensity H increases by increase of current I, the flux density B in the core changes as shown. flux () Near saturation linear current (I) 4/22/2017 Dr Awang Jusoh/Dr Makbul
19
Magnetic Equivalent Circuit
Analogy between magnetic circuit and electric circuit 4/22/2017 Dr Awang Jusoh/Dr Makbul
20
Magnetic Circuit with Air Gap
4/22/2017 Dr Awang Jusoh/Dr Makbul
21
Parallel Magnetic Circuit
Loop I NI = S33 + S11 = H3l3 + H1l1 Loop II NI = S33 + S22 = H3l3 + H2l2 Loop III 0 = S11 + S22 = H1l1 + H2l2 3 1 II 2 S3 S2 S1 I + NI - 4/22/2017 Dr Awang Jusoh/Dr Makbul
22
Electric vs Magnetic Circuit
Electric circuit Term Symbol Magnetic flux F Electric current I Flux density B Current density J Magnetomotive force Electromotive force E Permeability m Permitivity e Reluctance Resistance R 4/22/2017 Dr Awang Jusoh/Dr Makbul
23
Dr Awang Jusoh/Dr Makbul
Leakage Flux Part of the flux generated by a current-carrying coil wrapped around a leg of a magnetic core stays outside the core. This flux is called leakage flux. Useful flux 4/22/2017 Dr Awang Jusoh/Dr Makbul
24
Dr Awang Jusoh/Dr Makbul
Fringing Effect The effective area provided for the flow of lines of magnetic force (flux) in an air gap is larger than the cross-sectional area of the core. This is due to a phenomenon known as fringing effect. Air gap – to avoid flux saturation when too much current flows - To increase reluctance 4/22/2017 Dr Awang Jusoh/Dr Makbul
25
Dr Awang Jusoh/Dr Makbul
Example 1 Refer to Figure below, calculate:- 1) Flux 2) Flux density 3) Magnetic intensity Given r = 1,000; no of turn, N = 500; current, i = 0.1 A. cross sectional area, A = m2 , and means length core lC = 0.36 m. 1.75x10-5 Wb 0.175 Wb/m2 139 AT/Wb 4/22/2017 Dr Awang Jusoh/Dr Makbul
26
Dr Awang Jusoh/Dr Makbul
Example 2 Data- 1T – 700 at/m The Figure represents the magnetic circuit of a relay. The coil has 500 turns and the mean core path is lc = 400 mm. When the air-gap lengths are 2 mm each, a flux density of 1.0 Tesla is required to actuate the relay. The core is cast steel. a. Find the current in the coil. (6.93 A) b. Compute the values of permeability and relative permeability of the core (1.14 x 103 , 1.27) c. If the air-gap is zero, find the current in the coil for the same flux density (1 T) in the core. ( 0.6 A) Pg 8 : SEN 4/22/2017 Dr Awang Jusoh/Dr Makbul
27
Electromagnetic Induction
An emf can be induced in a coil if the magnetic flux through the coil is changed. This phenomenon is known as electromagnetic induction. The induced emf is given by Faraday’s law: The induced emf is proportional to the rate of change of the magnetic flux. This law is a basic law of electromagnetism relating to the operating principles of transformers, inductors, and many types of electrical motors and generators.
28
Electromagnetic Induction
Faraday's law is a single equation describing two different phenomena: The motional emf generated by a magnetic force on a moving wire, and the transformer emf generated by an electric force due to a changing magnetic field. The negative sign in Faraday's law comes from the fact that the emf induced in the coil acts to oppose any change in the magnetic flux. Lenz's law: The induced emf generates a current that sets up a magnetic field which acts to oppose the change in magnetic flux.
29
Lenz’s Law An induced current has a direction such that the magnetic field due to the induced current opposes the change in the magnetic flux that induces the current. As the magnet is moved toward the loop, the B through the loop increases, therefore a counter-clockwise current is induced in the loop. The current produces its own magnetic field to oppose the motion of the magnet If we pull the magnet away from the loop, the B through the loop decreases, inducing a current in the loop. In this case, the loop will have a south pole facing the retreating north pole of the magnet as to oppose the retreat. Therefore, the induced current will be clockwise.
30
Self-Inductance From Faraday’s law
Where l is the flux linkage of the winding is defined as For a magnetic circuit composed of constant magnetic permeability, the relationship between f and i will be linear and we can define the inductance L as It can be shown later that
31
Self-Inductance Henry
For a magnetic circuit having constant magnetic permeability So, Henry
32
Mutual Inductance i1 i2 + + N1 N2 g l1 l2 turns turns - -
Notice the current i1 and i2 have been chosen to produce the flux in the same direction. It is also assumed that the flux is confined solely to the core and its air gap. Magnetic core Permeability m, Mean core length lc, Cross-sectional area Ac
33
Mutual Inductance The total mmf is therefore with the reluctance of the core neglected and assuming that Ac = Ag the core flux is If the equation is broken up into terms attributable to the individual current, the flux linkages of coil 1 can be expressed as
34
Mutual Inductance where is the self-inductance of coil 1 and
is the flux linkage of coil 1 due to its own current i1. The mutual inductance between coils 1 and 2 is and is the flux linkage of coil 1 due to current i2.
35
Mutual Inductance Similarly, the flux linkage of coil 2 is where
is the mutual inductance and is the self-inductance of coil 2.
36
Mutual Inductance: Example
i2 + + N1 N2 g l1 l2 turns turns - - Magnetic core Permeability m >> mo, Cross-sectional area Ac = Ag = 1 cm X cm Air gap length, g = 2 mm N1 = 100 turns, N2 =200 turns Find L11, L22, and L12 = L21 = M
37
Magnetic Stored Energy
We know that for a magnetic circuit with a single winding and For a static magnetic circuit the inductance L is fixed For a electromechanical energy device, L is time varying
38
Magnetic Stored Energy
The power p is Thus the change in magnetic stored energy The total stored energy at any l is given by setting l1 = 0:
Similar presentations
© 2024 SlidePlayer.com Inc.
All rights reserved.