1. TL250-Internet Communicator

2. Compatibility

3. Specifications 250mA @12 VDC current draw 12 VDC input voltage Size: 3.25” × 5.25” (8.3 × 13.3)cm Operating Temperature: 32°- 122°F (0°-49°C) Output Protocols: UDP/IP 10/100 BaseT half duplex Input Protocols: PC-Link (SIA format) Connectors: 4-pin header for the PC-Link and RJ-45 for Ethernet Network: Ethernet LAN/WAN 10 BaseT, 10/100 BaseT or 100 BaseT Downloading Support for PC4020 V3.3+/PC5020/PC1616/PC1832/PC1864 Control Panel: using DLS2002 and/or DLS2002 System Administrator software 4 digital inputs (can be increased to 12 using the PC5108) Capable of sending alarm messages to 2 e-mail addresses

4. Board Overview PC Link Header to Panel Network Connection LED1 = Speed Status (ON = 100Mbps Connection OFF = 10Mbps Connection) LED2 = Activity Status (Displays Network Traffic RX/TX ) LED3 = Link Status (ON = Ethernet Present OFF = Ethernet Absent) Zone 1 - 4Keybus to PC5108 12VDC and GND

5. Status LED Flashes Per sec. TL250 Status 1/3 Flash-Normal 1 Flash -Network Absent 2 Flash -Invalid Account 3 Flash -Receiver 1 Absent 4 Flash -Panel Absent 5 Flash -Inputs Alarms 6 Flash -FTC 1 7 Flash -PC5108 Absent 8 Flash -PC5108 Tamper 9 Flash -FTC 2 10 Flash -Key switch Arm 11 Flash -Remote Programming 12 Flash -Local Programming 13 Flash -Receiver #2 Absent

6. Connecting to the panel 12VDC and GND Connect Network Cable Connect PC-Link Cable

7. Programming Requirements Static IP Address Programming IP address of TL250 IP address of Subnet Mask IP address of DRL3IP IP address of Network Gate Account Number Dynamic IP Address Programming IP address of DRL3IP Account Number Example IP Address 192.168.0.99 255.255.255.0 209.202.119.7 192.168.0.1 0000001234

8. Programming (4020) Press [*] to select System Area Select (00) <> Installer Opt’s Select (04) <> Communicator Scroll over to Comms Toggles and press [*] Select Toggle <> T-Link Enable Y Scroll over to Communicator and press [*] Scroll until you see an option for the T-Link and press [*] to enable the option Select (00) <> System Area Select (01) <> Comms Toggles Enter installer programming by pressing *8 followed by your installers code

9. Programming continued… Press [#] to Exit Comms Toggles Select (01) <> Comms Toggles Select (06) <> T-Link Module Enter a 3 digit Section number followed by the entry Scroll over to T-Link Module and press [*] Select Entry # Ent 001-999 _

10. Select Entry # Ent 001-999 001 Enter IP Address 192.168.000.099 Select Entry # Ent 001-999 002 Select Entry #1 Enter 00-FF 00 Select Entry # Ent 001-999 003 Enter IP Address 000.000.000.000 Select Entry # Ent 001-999 007 Enter IP Address 000.000.000.000 Enter the 12 digit IP Address of the TL250 followed by [#]. This should be given to you by your IT department. ENTER ALL ZERO’S FOR DHCP. Enter the 12 digit Subnet Mask followed by [#]. This should be given to you by your IT department. DO NOT PROGRAM FOR DHCP Enter the 6 digit account number for the TL250 followed by [#] of the TL250. This should be given to you by your central station. If you account is only 4 digits, enter 00 00 00 then the 4 digit account number Enter the 12 digit IP Address of the DRL3IP followed by [#]. This should be given to you by your central station. Select Entry # Ent 001-999 008 Enter IP Address 000.000.000.000 Enter the 12 digit IP Address of the Gateway followed by [#]. This should be given to you by your IT department. DO NOT PROGRAM FOR DHCP Programming continued…

11. Select Entry # Ent 001-999 004 Enter Hex Data 0000000000000000 Enter the FIRST 16 hexadecimal digits of the Encryption key. This is provided to you by your central station. Select Entry # Ent 001-999 005 Enter Hex Data 0000000000000000 Enter the LAST 16 hexadecimal digits of the Encryption key. This is provided to you by your central station. Select Entry # Ent 001-999 023 Enter Hex Data 00 Enter [01] to enable Supervision for Network Supervision. DO NOT PROGRAM FOR UN- SUPERVISED ACCOUNTS Select Entry #1 Enter 00-FF 99 Enter [999] to default the TL250 Enter [55], wait 30 seconds then press [#] all the way out of programming. Select Entry # Ent 001-999 999 Optional - If Network Supervision is Required… Optional - If 128 AES Encryption is Required… Programming continued…

12. 4020 Panel Programming Ref# 0004000000 Panel Tel number = CAAA Ref# 000400XX01 Comms Format = SIA FSK Ref# 000401 Auto SIA = Y Ref# 000400XX02 Dialer Directions = Alarms Y etc… Ref# 000300 DLS Enabled* = Y *if downloading is required

13. Programming Power Series TL250 Programming: Section 382 opt 5 PC-Link Active= enabled All TL250 programming in section [851] [001] –TL250 IP address, [002] –Subnet Mask, [003] -6 digit account number, [007] –DRL3IP IP address, [008] –Gateway [999], enter a 55 to restart (00 to default)

14. Power Series Communication Programming: Section 301 Panel Tel number = DCAA Section 350 Comms Format = SIA FSK Section 381 opt 3 Auto SIA = enabled Section 401 opt 1 DLS Enabled* = enabled *if downloading is required Programming Power Series

15. DLS 2002 Software DLS2002 Programming a panel via TL250 Ensure the DLS2002 TL250 Driver is installed (DLS2002 T-Link II Driver.exe)

16. Select TCP IP then click OK Programing the panel Via DLS2002 and TL250: Change Modem to TCP/IP DLS 2002 Software

17. IP address of TL250 DLS2002 Programming a panel via TL250 Enter the TL250’s IP address when an account is created or edited under account properties

18. DLS2002 Programming a panel via TL250 Upload/download control panel as usual

19. Questions?

20. Thank you for your time For future assistance, feel free to contact me at gharman@dsc.com