1. Electric Circuit Theory
Chapter 3
Methods of Analysis
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.

2. Methods of Analysis - Chapter 3
3.1 Introduction Nodal analysis. 3.2 Nodal analysis with dependent sources. 3.3 Nodal analysis with supernode. 3.4 Mesh analysis. 3.5 Mesh analysis with dependent sources. 3.6 Mesh analysis with supermesh 3.7 Source transformation 3.8 Norton and Thevenin equivalent circuit 3.9 Maximum power transfer and superposition

3. 3.1 Introduction Nodal analysis
If you are given the following circuit, how can we determine (1) the voltage across each resistor, (2) current through each resistor. (3) power generated by each current source, etc.
What are the things which we need to know in order to determine the answers?

4. How should we apply these laws to determine the answers?
3.1 Introduction Nodal analysis.
Things we need to know in solving any resistive circuit with current and voltage sources only:
Kirchhoff’s Current Laws (KCL)
Kirchhoff’s Voltage Laws (KVL)
Ohm’s Law
How should we apply these laws to determine the answers?

5. Nodal Analysis (1)
It provides a general procedure for analyzing circuits using node voltages as the circuit variables.
Example 1 3

6. Nodal Analysis (2) Steps to determine the node voltages:
Select a node as the reference node.
Assign voltages v1,v2,…,vn-1 to the remaining n-1 nodes. The voltages are referenced with respect to the reference node.
Apply KCL to each of the n-1 non-reference nodes. Use Ohm’s law to express the branch currents in terms of node voltages.
Solve the resulting simultaneous equations to obtain the unknown node voltages.

7. Nodal Analysis (3)
Example 2 – circuit independent current source only
Apply KCl at node 1 and 2 v1 v2 3
*Refer to in-class illustration, textbook, answer v1 = -2V, v2 = -14V

9. 2 method to solve
1 : Elimination technique
2 : Cramer’s Rule

10. Try this

11. 3.2 Nodal Analysis with dependent Source
Example 3 – current with dependant current source
answer v1= 4.8V, v2 = 2.4V, v3 = -2.4V

12. Nodal Analysis with Voltage Source
Example 4 –circuit with independent voltage source
How to handle the 2V voltage source?

13. 3.3 Nodal Analysis with Supernode (1)
A super-node is formed by enclosing a (dependent or independent) voltage source connected between two non-reference nodes and any elements connected in parallel with it.
*Note: We analyze a circuit with super-nodes using the same three steps mentioned above except that the super-nodes are treated differently.

14. 3.3 Nodal Analysis with supernode (2)
Basic steps:
Take off all voltage sources in super-nodes and apply KCL to super-nodes.
Put voltage sources back to the nodes and apply KVL to relative loops.

15. 3.3 Nodal Analysis with Supernode(3)
Example 5 – circuit with independent voltage source
Super-node => 2-i1-i2-7 = 0
Apply KVL => v1+2-v2 = 0

18. 3.3 Nodal Analysis with supernode (4)
Example 6 – circuit with two independent voltage sources

19. Solution

20. v1=26.67, v2 =6.67 ,v3=173.33, v4=-46.67

21. 3.3 Nodal Analysis with Supernode (5)
Example 7 – circuit with two independent voltage sources
-i1-i2 + i3 = 0
-i3-i5-i4 + i1 = 0
v1-20-v2 = 0
v3-3vx-v4 = 0

22. 3.4 Introduction to Mesh Analysis (1)
Mesh analysis provides another general procedure for analyzing circuits using mesh currents as the circuit variables.
Nodal analysis applies KCL to find unknown voltages in a given circuit, while mesh analysis applies KVL to find unknown currents.
A mesh is a loop which does not contain any other loops within it.

23. 3.4 Introduction to Mesh Analysis (2)
Steps to determine the mesh currents:
Assign mesh currents i1, i2, …, in to the n meshes.
Apply KCL to each of the n meshes. Use Ohm’s law to express the voltages in terms of the mesh currents.
Solve the resulting n simultaneous equations to get the mesh currents.

24. 3.4 Introduction to Mesh Analysis (3)
Example 8 – circuit with independent voltage sources
Note:
i1 and i2 are mesh current (imaginative, not measurable directly)
I1, I2 and I3 are branch current (real, measurable directly)
I1 = i1; I2 = i2; I3 = i1 - i2
*Refer to in-class illustration, textbook

26. 3.4 Mesh Analysis with dependent source
Example 9 – circuit with dependent voltage source
*Refer to in-class illustration, textbook, answer Io = 1.5A

27. 3.5 Mesh Analysis with supermesh (1)
Circuit with current source
A super-mesh results when two meshes have a (dependent or independent) current source in common as shown in (a). We create a super-mesh by excluding the current source and any elements connected in series with it as shown in (b).
*Refer to in-class illustration, textbook

28. 3.5 Mesh Analysis with supermesh (2)
The properties of a super-mesh:
The current source in the super-mesh is not completely ignored; it provides the constraint equation necessary to solve for the mesh currents.
A super-mesh has no current of its own.
A super-mesh requires the application of both KVL and KCL.

29. 3.6 Mesh Analysis with supermesh (3)
The properties of a super-mesh:
The current source in the super-mesh is not completely ignored; it provides the constraint equation necessary to solve for the mesh currents.
A super-mesh has no current of its own.
A super-mesh requires the application of both KVL and KCL.

30. Nodal versus Mesh Analysis
To select the method that results in the smaller number of equations. For example:
Choose nodal analysis for circuit with fewer nodes than meshes.
*Choose mesh analysis for circuit with fewer meshes than nodes.
*Networks that contain many series connected elements, voltage sources, or supermeshes are more suitable for mesh analysis.
*Networks with parallel-connected elements, current sources, or supernodes are more suitable for nodal analysis.
If node voltages are required, it may be expedient to apply nodal analysis. If branch or mesh currents are required, it may be better to use mesh analysis.

31. 3.7 Source Transformation (1)
An equivalent circuit is one whose v-i characteristics are identical with the original circuit.
It is the process of replacing a voltage source vS in series with a resistor R by a current source iS in parallel with a resistor R, or vice versa.

32. 3.7 Source Transformation (2)+ +
(a) Independent source transform
(b) Dependent source transform
The arrow of the current source is directed toward the positive terminal of the voltage source.
The source transformation is not possible when R = 0 for voltage source and R = ∞ for current source. - - + + - -

33. 3.7 Source Transformation (3)
Example 4
Find io in the circuit shown below using source transformation.
*Refer to in-class illustration, textbook, answer io = 1.78A

34. 3.8a Norton’s Theorem (1)
It states that a linear two-terminal circuit can be replaced by an equivalent circuit of a current source IN in parallel with a resistor RN,
Where
IN is the short circuit current through
the terminals.
RN is the input or equivalent resistance
at the terminals when the independent
sources are turned off.
The Thevenin’s and Norton equivalent circuits are related by a source transformation.

35. 3.8a Norton’s Theorem (2) Example 7
Find the Norton equivalent circuit of the circuit shown below.
2 
(a)
6 
2vx
+  + vx  1V ix i
(b)
10 A
Isc
*Refer to in-class illustration, textbook, RN = 1W, IN = 10A.

36. 3.8b Thevenin’s Theorem (1)
It states that a linear two-terminal circuit (Fig. a) can be replaced by an equivalent circuit (Fig. b) consisting of a voltage source VTH in series with a resistor RTH,
where
VTH is the open-circuit voltage at the terminals.
RTH is the input or equivalent resistance at the terminals when the independent sources are turned off.

37. 3.8b Thevenin’s Theorem (2)
Example 5
Using Thevenin’s theorem, find the equivalent circuit to the left of the terminals in the circuit shown below. Hence find i.
6 
4 
(a)
RTh 2A
(b) +
VTh 
*Refer to in-class illustration, textbook, answer VTH = 6V, RTH = 3W, i = 1.5A

38. 3.8b Thevenin’s Theorem (3)
5  Ix
4  + 
(a)
1.5Ix i1 i2
3  o
VTh b a
1 V
0.5Ix
(b) i
Example 6
Find the Thevenin equivalent circuit of the circuit shown below to the left of the terminals.
*Refer to in-class illustration, textbook, answer VTH = 5.33V, RTH = 3W

39. 3.9a Maximum Power Transfer (1)
If the entire circuit is replaced by its Thevenin equivalent except for the load, the power delivered to the load is:
For maximum power dissipated in RL, Pmax, for a given RTH,
and VTH,
The power transfer profile with different RL

40. 3.9a Maximum Power Transfer (2)
Example 8
Determine the value of RL that will draw the maximum power from
the rest of the circuit shown below. Calculate the maximum power.
2 
4 
1 V + 
(a)
1 
3vx i v0  vx
RTH

42. 3.9b Superposition Theorem (1)
It states that the voltage across (or current through) an element in a linear circuit is the algebraic sum of the voltage across (or currents through) that element due to EACH independent source acting alone.
The principle of superposition helps us to analyze a linear circuit with more than one independent source by calculating the contribution of each independent source separately.

43. 3.9b Superposition Theorem (2)
We consider the effects of 8A and 20V one by one, then add the two effects together for final vo.

44. 3.9b Superposition Theorem (3)
Steps to apply superposition principle
Turn off all independent sources except one source. Find the output (voltage or current) due to that active source using nodal or mesh analysis.
Repeat step 1 for each of the other independent sources.
Find the total contribution by adding algebraically all the contributions due to the independent sources.

45. 3.9b Superposition Theorem (4)
Two things have to be keep in mind:
When we say turn off all other independent sources:
Independent voltage sources are replaced by 0 V (short circuit) and
Independent current sources are replaced by 0 A (open circuit).
Dependent sources are left intact because they are controlled by circuit variables.

46. 3.9b Superposition Theorem (5)
Example 2
Use the superposition theorem to find v in the circuit shown below.
3A is discarded by open-circuit
6V is discarded by short-circuit
*Refer to in-class illustration, text book, answer v = 10V

47. 3.9b Superposition Theorem (6)
Example 3
Use superposition to find vx in the circuit below.
Dependant source keep unchanged
2A is discarded by open-circuit
10V is discarded by open-circuit
20  v1
4 
10 V + 
(a)
0.1v1
4 
2 A
(b)
20 
0.1v2 v2
*Refer to in-class illustration, text book, answer Vx = 12.5V

48. Solution For Ex.3 (superposition)