Presentation is loading. Please wait.

Presentation is loading. Please wait.

1. At what type of tectonic boundary would you expect to find compression forces? ANS: convergent 2. What type of forces would you expect to form at divergent.

Similar presentations


Presentation on theme: "1. At what type of tectonic boundary would you expect to find compression forces? ANS: convergent 2. What type of forces would you expect to form at divergent."— Presentation transcript:

1 1. At what type of tectonic boundary would you expect to find compression forces? ANS: convergent 2. What type of forces would you expect to form at divergent plate boundaries? ANS: tension

2 3. When supercontinents come together, diversity ____________ (increases/decreases). ANS: decreases 4.When supercontinents _________________ (break apart/come together), isolation increases, leading to an increase in diversification. ANS: break apart 5.Other than photosynthesis, what process within the hydrologic cycle removes CO 2 from the atmosphere? ANS: formation of acid rain

3 6.What is the name of the fault which occurs at a transform boundary? ANS: Strike-slip fault 7. What type of fault results from tension forces? ANS: Normal fault 8. What type of force causes a reverse/thrust fault? ANS: compression 9. Why are sedimentary basins of particular importance to humans? ANS: it is in these basins that coal, oil and natural gas form.

4 10. Why is the Atlantic saltier than the Pacific? ANS: because the strengthened Gulf Stream occurred due to the joining of North and South America. This warm-water current causes more evaporation in the Atlantic, increasing salinity. The trade winds blow from east-west, and carry the freshwater in the form of rain across the isthmus of Panama, depositing freshwater in the Pacific, decreasing the salinity there. 11. Simplest type of fold… ANS: monocline 12. In a typical fold sequence of rock strata, the troughs are called ___________, and the crests are called _______________. ANS: Syncline; Anticline

5 13. When compression forces two blocks of Earth together, and one block slides over another, what type of fault is created? ANS: Reverse/thrust fault 14. The San Andreas fault is a strike-slip type fault. What type of plate boundary does it sit on? ANS: transform 15. The study of terrestrial surfaces is known as topography. Studying surface features beneath the ocean is known as ANS: Bathymetry

6 16. With what would you associate the word “orogeny”? ANS: The origin and evolution of mountains 17. What type of mountains would you associate with and expect to find as a result of the collision between two continental tectonic plates? ANS: Folded mountains 18. Why? ANS: Because the two continents are of approximately equal density, and subduction does not occur.

7 19. What type of plates would be converging to form volcanic mountains? ANS: A continental and an oceanic 20. How do plate tectonics recycle carbon? ANS: CO 2 is one of the main gases present in volcanic eruptions. Once in the atmosphere, it combines with water droplets, and precipitates out as acid rain (carbonic acid). Chemical weathering occurs once the rain hits the surface. The material is eroded away, and deposited elsewhere, where it becomes incorporated into a sedimentary rock formation (carbonate, perhaps in a basin). Once here, it slowly moves across the oceanic floor, (slab push/pull) until it reaches a subduction zone (could take millions of years). Here, it is subducted beneath the continental plate, and forced down close to the mantle, where the carbon again finds its way, in gaseous form (CO 2 ) out through the volcanic mountains that form along this boundary. 21. When Island Arcs and seamounts collide with continents, what type of accretion has occurred? ANS: Tectonic

8 22. When topographic features are weathered and eroded away, depositing them somewhere else, such as alluvial deposits by a river, what type of accretion has occurred? ANS: landmass accretion 23.Where is the next supercontinent supposed to accrete, according to computer models? ANS: near the north polar area 24. Humans have been producing more CO2 since the Industrial Revolution. It has been difficult for tectonics to keep up with the recycling of carbon. Which Earth subsystem has been most affected? ANS: Atmosphere

9 Use the following list to answer the questions below: GondwanaRodiniaPannotia PangaeaLaurasiaAmasia 25. Northern half of Pangaea known as this ANS: Laurasia 26. Supercontinent that caused snowball Earth ANS: Pannotia 27. Supercontinent when only bacteria had evolved ANS: Rodinia 28. Supercontinent of the future ANS: Amasia

10 29. The most complex of folds, which appear to have been upended, such as the one below, are known as what? ANS: Recumbent 30. The fault below is an example of what type of strike-slip? ANS: right-lateral


Download ppt "1. At what type of tectonic boundary would you expect to find compression forces? ANS: convergent 2. What type of forces would you expect to form at divergent."

Similar presentations


Ads by Google