1. PROSTHETIC PROCEDURE MANUAL BR SYSTEM

2. CEMENTED RESTORATION Impression Copings Set Screw Pick-up Transfer Implant Analog Cemented Abutment Angled Abutment

3. IMPRESSION COPINGS Implant Level – Pick-up Implant level impression, pick-up impression coping (open tray technique) Impression coping is packaged with corresponding guide pin Use 1.2mm Hex driver to assemble/ disassemble Engaging Guide Pin 1.2mm Hex Driver

4. IMPRESSION COPINGS Implant Level – Transfer Implant level impression, transfer impression coping (closed tray technique) Impression coping is packaged with corresponding guide pin Use 1.2mm Hex driver to assemble/ disassemble Engaging Guide Pin 1.2mm Hex Driver

5. IMPLANT ANALOG

6. CEMENTED ABUTMENT Fastening torque 30 Ncm HEIGHT CUFF DIAMETER Engaging 1.2mm Hex Driver

7. ANGLED ABUTMENT Options of 15 degrees and 25 degrees Angled Abutments are packaged alongside corresponding set screw Fastening torque 30 Ncm HEIGHT CUFF DIAMETER Engaging 1.2mm Hex Driver

8. SET SCREW Cemented Abutment screw is 10mm long Angled Abutments screw is 8mm long Set screws are packaged along with corresponding abutment LENGTH DIAMETER

9. CLINICAL PROCESS Fixing Impression Copings (1/3) View of patient’s mouth

10. CLINICAL PROCESS Fixing Impression Copings (2/3) Remove healing abutment / cover screw with 1.2mm Hex Driver Insert impression coping inside corresponding implant connection

11. CLINICAL PROCESS Fixing Impression Copings (3/3) Fasten impression coping with corresponding guide pin Tighten guide pin with 1.2mm hex driver

12. CLINICAL PROCESS Taking The Impression (1/6) Apply the light impression material on corresponding site of oral cavity

13. CLINICAL PROCESS Taking The Impression (2/6) Pour the heavy impression material inside the impression tray

14. CLINICAL PROCESS Taking The Impression (3/6) Position tray for impression taking Apply pressure until top part of guide pin appears wait for impression material to set Transfer impression copings will require prefabricated tray Pick-up impression copings will require previously customized tray

15. CLINICAL PROCESS Taking The Impression (4/6) Remove guide pin

16. CLINICAL PROCESS Taking The Impression (5/6) Check tray for impression errors / success

17. CLINICAL PROCESS Taking The Impression (6/6) Replace healing abutment / cover screw in corresponding site

18. LABORATORY PROCESS 1. Fixing Analogs & Making Artificial Gum (1/4) Fix analogs on corresponding impression coping

19. LABORATORY PROCESS 1 - Fixing Analogs & Making Artificial Gum (2/4) Apply (Spray) separating product on impression areas

20. LABORATORY PROCESS 1. Fixing Analogs & Making Artificial Gum (3/4) Apply artificial gum product on intervention area Wait for product to dry

21. LABORATORY PROCESS 1. Fixing Analogs & Making Artificial Gum (4/4) Trim gum

22. LABORATORY PROCESS 2. Master Modeling (1/3) Prepare (mix) the stone

23. LABORATORY PROCESS 2. Master Modeling (2/3) Pour the mixed stone inside the impression

24. LABORATORY PROCESS 2. Master Modeling (3/3) Master model finishing work

25. LABORATORY PROCESS 3. Abutment Milling (1/5) Fix the abutment to the analog

26. LABORATORY PROCESS 3. Abutment Milling (2/5) Abutment Milling (Step 1)

27. LABORATORY PROCESS 3. Abutment Milling (3/5) Abutment Milling (Step 2)

28. LABORATORY PROCESS 3. Abutment Milling (4/5) Abutment Milling (Step 3)

29. LABORATORY PROCESS 3. Abutment Milling (5/5) Post Milling

30. LABORATORY PROCESS 4. Pattern Resin & Wax-Up (1/3)

31. LABORATORY PROCESS 4. Pattern Resin & Wax-Up (2/3) Wax-up process (Steps 1 & 2)

32. LABORATORY PROCESS 4. Pattern Resin & Wax-Up (3/3) Wax-up process (Steps 3 & 4)

33. LABORATORY PROCESS 5. Sprewing (1/2) Sprewing (Step 1)

34. LABORATORY PROCESS 5. Sprewing (2/2) Sprewing (Step 2)

35. LABORATORY PROCESS 6. Investment (1/2) Investment (Step 1)

36. LABORATORY PROCESS 6. Investment (2/2) Investment (Step 2) Burn out (Step 3)

37. LABORATORY PROCESS 7. Casting Cast and extract cast structure

38. LABORATORY PROCESS 8. Adaptation & Metal Trimming Check cast structure for adaptation on master model

39. LABORATORY PROCESS 9. Finishing

40. LABORATORY PROCESS 10. Transfer Jig (1/2) Make the transfer Jig

41. LABORATORY PROCESS 10. Transfer Jig (2/2) Place the abutment(s) inside the oral cavity by using the transfer jig