Presentation is loading. Please wait.

Presentation is loading. Please wait.

Development of the FW Mobile Tiles Concept Mohamed Sawan, Edward Marriott, Carol Aplin University of Wisconsin-Madison Lance Snead Oak Ridge National Laboratory.

Published byJonathan Peters Modified over 8 years ago

Similar presentations

Presentation on theme: "Development of the FW Mobile Tiles Concept Mohamed Sawan, Edward Marriott, Carol Aplin University of Wisconsin-Madison Lance Snead Oak Ridge National Laboratory."— Presentation transcript:

1 Development of the FW Mobile Tiles Concept Mohamed Sawan, Edward Marriott, Carol Aplin University of Wisconsin-Madison Lance Snead Oak Ridge National Laboratory 1 HAPL Project Meeting Santa Fe, NM April 8-9, 2008

2 1.Configuration with consideration for laser beam port accommodation and tile insertion and removal 2.Neutronics assessment of blanket design options with FW mobile tiles OUTLINE 2

3  Tiles will traverse the cylindrical chamber walls over a certain period of time  Once removed, the tiles will be reprocessed for tritium removal and recycling  Tiles will then be reinserted along the chamber walls  Top and bottom chamber tiles will be stationary and will be removed and reprocessed as needed Concept 3

4 These tiles traverse the chamber along a coolant rod (shown in blue) At the location of the laser ports, the tiles will rotate around the coolant rod by following a guiding rail on the coolant rod Laser Port Tiles 4 Top View Isometric View Mobile Tile

5  For sections of chamber walls without laser beam penetration, larger tiles will be used  These tiles will traverse vertically through the chamber without the need to twist to open for lasers Chamber Wall Tiles 5 Wall Tiles Coolant Plates Top View Isometric View

6 Overall Wall Geometry 6 Isometric View Top View Wall Tiles Coolant Plates Coolant Rod Twisting Tile

7 Top and Bottom Geometry 7 Coolant In Coolant Out Tiles In/Out Top Tile Laser Port Representative Cross Section TilesCoolant Plates  Top and Bottom tiles will be stationary  Four tiles on the top and bottom each will have an opening for the lasers  Tiles are installed by sliding them into place on the coolant plates (coolant plates shown in blue)

8 Full Chamber Representation 8 Isometric view without lasers Top view with lasers Isometric view with lasers

9  Neutronics calculations performed to assess breeding potential for different design options  Breeder options: Ceramic breeder (Li 4 SiO 4 ), Flibe, Liq. Li, LiPb  Coolant options: Liq. Na, Liq. breeder  Structure options: FS, V-4Cr-4Ti, SiC f /SiC  Considered adding Be 2 C in the graphite tiles to improve TBR  7 and 10 cm average tile thicknesses considered followed by a meter thick blanket  Cylindrical chamber with 10-m radius  Used HAPL target spectrum in 175 neutron, 42 gamma groups  A zone consisting of 85% FS, 15% He used behind blanket to represent reflection from shield/VV  Required TBR>1.1 for tritium self-sufficiency Neutronics Assessment and Assumptions 9

10 TBR Results for Ceramic Breeder Options  Li 4 SiO 4 with 30% Li-6 enrichment was found in previous calculations to maximize TBR  FS structure is used with Na coolant  Adding 30% Be 2 C in FW tiles and blanket is essential for achieving tritium self-sufficiency  Average FW tile thickness should be kept at 7 cm or less FW TilesBlanketFW Tile Thickness % FS % Na %C%C % Be 2 C % FS % Na %C%C % Li 4 SiO 4 % Be 2 C 7 cm10 cm 101575010 7000.9110.868 1015552010 50201.0590.999 1015552010 40201.0961.024 1015453010 40301.1271.056 10

11 TBR Results for Liquid Breeder Options (Na in tiles)  Three liquid breeder options were considered with three structural materials  Natural Li is used except for LiPb where 90% Li-6 enrichment was also considered  FW tiles consist of 75% C, 10% structure, 15% Na  Blanket consists of 90% liq. Breeder and 10% structure  Nat. Li and enriched LiPb yield adequate TBR with any structural material for 7 cm or less tiles  V provides best neutron economy with FS giving the least  Flibe does not allow tritium self-sufficiency with any structural material FlibeLiLiPb (nat) LiPb (90% Li-6) FS0.9491.1500.8121.213 V1.0141.2230.9541.258 SiC1.0121.1591.1441.248 FlibeLiLiPb (nat) LiPb (90% Li-6) FS0.8651.0450.6901.075 V0.9331.1190.8171.130 SiC0.9591.0801.0421.149 10 cm tiles7 cm tiles 11

12 TBR Results for Liquid Breeder Options (breeder in tiles)  To avoid using two coolants we considered the option of cooling the FW tiles with the same liquid breeder used in blanket  FW tiles consist of 75% C, 10% structure, 15% liq. breeder  Blanket consists of 90% liq. breeder and 10% structure  Breeding increased by ~2-5% when liquid breeder is used instead of Na to cool FW tiles with conclusions regarding adequacy of TBR remaining the same FlibeLiLiPb (nat) LiPb (90% Li-6) FS0.9831.1820.8761.267 V1.0431.2511.0221.303 SiC1.0301.1821.1911.286 FlibeLiLiPb (nat) LiPb (90% Li-6) FS0.9341.1070.8081.185 V1.0011.1770.9481.229 SiC0.9921.1161.1281.210 10 cm tiles7 cm tiles 12

13 Enhancing TBR for Flibe Blanket  Using Flibe as breeder does not provide adequate tritium breeding with any of the candidate structural materials  We assessed the effect of adding Be 2 C to the graphite FW tiles  Tiles have 10% structure and 15% Na with the remaining 75% split between C and Be 2 C  Blanket consists of 90% Flibe and 10% structure  Tritium self-sufficiency with a Flibe blanket can be achieved only with at least 30% Be 2 C added in FW tiles and either SiC or V structure used 0% Be 2 C 20% Be 2 C 30% Be 2 C 40% Be 2 C FS0.9831.0071.0341.061 V1.0431.0751.1041.131 SiC1.0301.0941.1341.175 7 cm tiles 13

14 Issues for Coolant/Breeder Choice  High surface heat flux (~0.4 MW/m 2 ) and volumetric heating (~4 W/cm 3 ) in FW tiles require coolant with good heat removal capability. Liquid Na is the best with Li close second and Flibe being the worst  With its low melting point and light weight, liq. Na is the preferred option for cooling the FW tiles but adds complication of having two coolants in the power cycle CoolantT m ( C)  (g/cm 3 ) C p (J/gK)k(W/mK) Na98~0.9~1.3~84 Li181~0.5~4.2~60 Flibe459~2~2.4~1 LiPb234~9.5~0.18~15 Physical properties depend on temperature range 14

15 Preferred Design Options  To avoid the complexity of having two coolants in the power cycle, it is preferred to cool the FW tiles with the same liquid breeder used in the blanket  While both Li and LiPb can provide adequate TBR, Li is the preferred option due to its better heat removal capability, light weight leading to less pumping power, and no need for enrichment. The main issue is safety concern that can be mitigated by using He cooling in shield/VV  Choice of structural material depends on compatibility with Li. While V and SiC yield better TBR and can operate at higher temperatures than FS, they are more expensive, require more R&D and compatibility with Li could limit their operating temperature 15

16 Blanket FW Nuclear Heating in FW Tiles and Blanket  Nuclear heating and surface heat flux calculated for use in thermal analysis  Nuclear heating results scale with the neutron wall loading 16  Peak surface heat flux at midplane =0.37 MW/m 2 Drops to 0.13 MW/m 2 at top/bottom with an average value of 0.26 MW/m 2  Peak neutron wall loading at midplane =1.09 MW/m 2 Drops to 0.39 MW/m 2 at top/bottom with an average value of 0.77 MW/m 2

17 17 Surface Heat Load and Neutron Wall Load Distribution  Distributions of surface heat flux and neutron wall loading peak at mid-plane and centers of chamber’s top and bottom  Peak surface heat flux =0.37 MW/m 2  Peak neutron wall loading =1.09 MW/m 2  Axial values drop as one moves away from mid- plane scaling as cos 3   Radial values at top/bottom drop as one moves away from center scaling as cos 3   Average surface heat flux  Side 0.26 MW/m 2  Top/bottom 0.22 MW/m 2  Average neutron wall loading  Side 0.77 MW/m 2  Top/bottom 0.64 MW/m 2 173/6/08 Cylindrical chamber assumed with 10 m radius and 20 m height  

18 Conclusions  Conceptual configuration developed with consideration for laser beam port accommodation and simple tile insertion and removal scheme  Tritium self-sufficiency can be achieved with a variety of options employing FW mobile tiles  Using ceramic breeders or Flibe is not recommended due to requiring at least 30% Be 2 C added in FW tiles  While liquid Na has the best heat removal capability for FW tiles, it adds the complexity of having two coolants. Either Li or LiPb can be used also to cool the FW tiles  Li is the preferred breeder/coolant due to better heat removal capability, lighter weight, and no enrichment  Choice of structural material depends primarily on compatibility with Li 18

Download ppt "Development of the FW Mobile Tiles Concept Mohamed Sawan, Edward Marriott, Carol Aplin University of Wisconsin-Madison Lance Snead Oak Ridge National Laboratory."

Similar presentations

Mobile Tiles for Inertial Fusion First Wall/Blanket Systems Lance L Snead 1, Mohamed Sawan 2, Pete Papano 1, Edward Marriott 2, and Carol S Aplin 2 1 Materials.

Mobile Tiles for Inertial Fusion First Wall/Blanket Systems Lance L Snead 1, Mohamed Sawan 2, Pete Papano 1, Edward Marriott 2, and Carol S Aplin 2 1 Materials.
Lesson 17 HEAT GENERATION

Lesson 17 HEAT GENERATION
First Wall Heat Loads Mike Ulrickson November 15, 2014.

First Wall Heat Loads Mike Ulrickson November 15, 2014.
Scoping Neutronics Analysis in Support of FDF Design Evolution Mohamed Sawan University of Wisconsin-Madison With input from R. Stambaugh, C. Wong, S.

Scoping Neutronics Analysis in Support of FDF Design Evolution Mohamed Sawan University of Wisconsin-Madison With input from R. Stambaugh, C. Wong, S.
September 24-25, 2003 HAPL meeting, UW, Madison 1 Armor Configuration & Thermal Analysis 1.Parametric analysis in support of system studies 2.Preliminary.

September 24-25, 2003 HAPL meeting, UW, Madison 1 Armor Configuration & Thermal Analysis 1.Parametric analysis in support of system studies 2.Preliminary.
March 21-22, 2006 HAPL meeting, ORNL 1 Status of Chamber and Blanket Effort A. René Raffray UCSD With contributions from: M. Sawan B. Robson G. Sviatoslavsky.

March 21-22, 2006 HAPL meeting, ORNL 1 Status of Chamber and Blanket Effort A. René Raffray UCSD With contributions from: M. Sawan B. Robson G. Sviatoslavsky.
09 FNST meeting Preliminary Neutronics Analysis for IB Shielding Design on FNSF (Standard Aspect Ratio) Haibo Liu Robert Reed Fusion Science and Technology.

09 FNST meeting Preliminary Neutronics Analysis for IB Shielding Design on FNSF (Standard Aspect Ratio) Haibo Liu Robert Reed Fusion Science and Technology.
SYSTEMS AND ENGINEERING TECHNOLOGY INVESTIGATION OF AN INERTIAL CONFINEMENT FUSION-FISSION HYBRID REACTOR Kiranjit Mejer PTNR Research Project 2009 Frazer-Nash.

SYSTEMS AND ENGINEERING TECHNOLOGY INVESTIGATION OF AN INERTIAL CONFINEMENT FUSION-FISSION HYBRID REACTOR Kiranjit Mejer PTNR Research Project 2009 Frazer-Nash.
FNSF Blanket Testing Mission and Strategy Summary of previous workshops 1 Conclusions Derived Primarily from Previous FNST Workshop, August 12-14, 2008.

FNSF Blanket Testing Mission and Strategy Summary of previous workshops 1 Conclusions Derived Primarily from Previous FNST Workshop, August 12-14, 2008.
Views on Neutronics and Activation Issues Facing Liquid-Protected IFE Chambers L. El-Guebaly and the ARIES Team Fusion Technology Institute University.

Views on Neutronics and Activation Issues Facing Liquid-Protected IFE Chambers L. El-Guebaly and the ARIES Team Fusion Technology Institute University.
1 LOCA/LOFA Analyses for LiPb/FS System Carl Martin, Jake Blanchard Fusion Technology Institute University of Wisconsin - Madison ARIES-CS Project Meeting.

1 LOCA/LOFA Analyses for LiPb/FS System Carl Martin, Jake Blanchard Fusion Technology Institute University of Wisconsin - Madison ARIES-CS Project Meeting.
First Wall Thermal Hydraulics Analysis El-Sayed Mogahed Fusion Technology Institute The University of Wisconsin With input from S. Malang, M. Sawan, I.

First Wall Thermal Hydraulics Analysis El-Sayed Mogahed Fusion Technology Institute The University of Wisconsin With input from S. Malang, M. Sawan, I.
September 3-4, 2003/ARR 1 Initial Assessment of Maintenance Scheme for 2- Field Period Configuration A. R. Raffray X. Wang University of California, San.

September 3-4, 2003/ARR 1 Initial Assessment of Maintenance Scheme for 2- Field Period Configuration A. R. Raffray X. Wang University of California, San.
The Potential for Graphite Oxidation in Dry Wall ICF Chambers El S. Mogahed, I. N Sviatoslavsky, J. G. Murphy, H. Y. Khater, M. H. Anderson, and G. L.

The Potential for Graphite Oxidation in Dry Wall ICF Chambers El S. Mogahed, I. N Sviatoslavsky, J. G. Murphy, H. Y. Khater, M. H. Anderson, and G. L.
January 11-13, 2005/ARR 1 Ceramic Breeder Blanket Coupled with Brayton Cycle Presented by: A. R. Raffray (University of California, San Diego) With contributions.

January 11-13, 2005/ARR 1 Ceramic Breeder Blanket Coupled with Brayton Cycle Presented by: A. R. Raffray (University of California, San Diego) With contributions.
June 16, 2004/ARR 1 Thermal-Hydraulic Study of ARIES-CS Ceramic Breeder Blanket Coupled with a Brayton Cycle Presented by A. R. Raffray With contributions.

June 16, 2004/ARR 1 Thermal-Hydraulic Study of ARIES-CS Ceramic Breeder Blanket Coupled with a Brayton Cycle Presented by A. R. Raffray With contributions.
Status of safety analysis for HCPB TBM Susana Reyes TBM Project meeting, UCLA, Los Angeles, CA May 10-11, 2006 Work performed under the auspices of the.

Status of safety analysis for HCPB TBM Susana Reyes TBM Project meeting, UCLA, Los Angeles, CA May 10-11, 2006 Work performed under the auspices of the.
November 4-5, 2004/ARR 1 ARIES-CS Power Core Options for Phase II and Focus of Engineering Effort A. René Raffray University of California, San Diego ARIES.

November 4-5, 2004/ARR 1 ARIES-CS Power Core Options for Phase II and Focus of Engineering Effort A. René Raffray University of California, San Diego ARIES.
November 8-9, 2005 1 Blanket Design for Large Chamber A. René Raffray UCSD With contributions from M. Sawan (UW), I. Sviatoslavsky (UW) and X. Wang (UCSD)

November 8-9, Blanket Design for Large Chamber A. René Raffray UCSD With contributions from M. Sawan (UW), I. Sviatoslavsky (UW) and X. Wang (UCSD)
Status of 3-D Analysis, Neutron Streaming through Penetrations, and LOCA/LOFA Analysis L. El-Guebaly, M. Sawan, P. Wilson, D. Henderson, A. Ibrahim, G.

Status of 3-D Analysis, Neutron Streaming through Penetrations, and LOCA/LOFA Analysis L. El-Guebaly, M. Sawan, P. Wilson, D. Henderson, A. Ibrahim, G.

Similar presentations

Ads by Google