1. Lecture 33: Chapter 5 Today’s topic –Cache Replacement Algorithms –Multi-level Caches –Virtual Memories 1

2. Associative Cache Example 2 The location of the block with address ‘12’ varies depending on the type of the cache memory and degree of associativity. In a direct mapped of size 8 blocks, the memory address ‘12’ is associated with the block address ‘4’ in the cache memory because 12 = (1100) 2 Thus (12 modulo 8) = 4 = (100) 2 is used to find location in the cache. In a 2-way set associative, there will be 4 sets. Thus, the corresponding location is cash is the block number (12 modulo 4) = 0. In a full associative scenario, the memory block for block address 12 can appear in any of the eight cache blocks.

3. Set Associative Cache Organization 3

4. Replacement Policy Direct mapped: no choice Set associative –Prefer non-valid entry, if there is one –Otherwise, choose among entries in the set Least-recently used (LRU) –Choose the one unused for the longest time Simple for 2-way, manageable for 4-way, too hard beyond that Random –Gives approximately the same performance as LRU for high associativity 4

5. Multilevel Caches Primary cache attached to CPU –Small, but fast Level-2 cache services misses from primary cache –Larger, slower, but still faster than main memory Main memory services L-2 cache misses Some high-end systems include L-3 cache 5

6. Multilevel Cache Example Given –CPU base CPI = 1, clock rate = 4GHz –Miss rate/instruction = 2% –Main memory access time = 100ns With just primary cache –Miss penalty = 100ns/0.25ns = 400 cycles –Effective CPI = 1 + 0.02 × 400 = 9 6

7. Example (cont.) Now add L-2 cache –Access time = 5ns –Global miss rate to main memory = 0.5% Primary miss with L-2 hit –Penalty = 5ns/0.25ns = 20 cycles Primary miss with L-2 miss –Extra penalty = 400 cycles CPI = 1 + 0.02 × 20 + 0.005 × 400 = 3.4 Performance ratio = 9/3.4 = 2.6 7

8. Cache Summary Common principles apply at all levels of the memory hierarchy –Based on notions of caching At each level in the hierarchy –Block placement –Finding a block –Replacement on a miss –Write policy The BIG Picture 8

9. Block Placement Determined by associativity –Direct mapped (1-way associative) One choice for placement –n-way set associative n choices within a set –Fully associative Any location Higher associativity reduces miss rate –Increases complexity, cost, and access time 9

10. Finding a Block AssociativityLocation methodTag comparisons Direct mappedIndex1 n-way set associative Set index, then search entries within the set n Fully associativeSearch all entries#entries Full lookup table0 10

11. Replacement Choice of entry to replace on a miss –Least recently used (LRU) Complex and costly hardware for high associativity –Random Close to LRU, easier to implement 11

12. Write Policy Write-through –Update both upper and lower levels –Simplifies replacement, but may require write buffer Write-back –Update upper level only –Update lower level when block is replaced –Need to keep more state 12

13. Sources of Misses Compulsory misses (aka cold start misses) –First access to a block Capacity misses –Occur because blocks are being discarded from cache because cache cannot contain all blocks needed for program execution (program working set is much larger than cache capacity). –Due to finite cache size –A replaced block is later accessed again Conflict misses (aka collision misses) –In the case of set associative or direct mapped block placement strategies, conflict misses occur when several blocks are mapped to the same set or block frame; also called collision misses or interference misses. –Due to competition for entries in a set –Would not occur in a fully associative cache of the same total size 13

14. Virtual Memory Use main memory as a “cache” for secondary (disk) storage –Managed jointly by CPU hardware and the operating system (OS) Programs share main memory –Each gets a private virtual address space holding its frequently used code and data –Protected from other programs CPU and OS translate virtual addresses to physical addresses –VM “block” is called a page –VM translation “miss” is called a page fault 14

15. Address Translation Fixed-size pages (e.g., 4K) The page size is 4K = 2 12. The number of physical pages allowed in memory is 2 18 since the physical page number has 18 bits in it. Thus, main memory can have at most 1GB while the virtual address space is 4GB. 15

16. Page Fault Penalty On page fault, the page must be fetched from disk –Takes millions of clock cycles –Handled by OS code Try to minimize page fault rate –Fully associative placement –Smart replacement algorithms 16