1. Wireless Network Security Lab Last Update 2011.06.01 1.0.0 1Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com

2. Method Used This lab will be done in Packet Tracer 5.2 or later Start Packet Tracer 2 Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com

3. Create the Lab Network Create this network in it Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com 3

4. Create the Lab Network Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com 4

5. Create the Lab Network The connections to the Server-PT devices from the Access Point switch ports are straight-through cables Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com 5

6. Configure the Access Point Click on the Linksys WRT300N Wireless Access Point –Open the GUI tab and ensure that DHCP is set to Automatic Configuration Leave the Access Point’s IP address at the default value of 192.168.0.1/24 Enable the DHCP Server and leave the Start IP Address as 192.168.0.100 Set the maximum number of DHCP clients to 4 Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com 6

7. Configure the Wireless Client Open the Physical tab of the PC-PT computer and turn the power off Remove the Ethernet module and replace it with the Linksys WMP-300N wireless module Turn the power back on After a few seconds you should have a wireless connection to the access point Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com 7

8. Enable WEP The original security method used in wireless LANs was WEP Let’s see how it is enabled On the WRT-300N access point select the Config tab –Change the SSID to CCNP –Enable WEP Authentication Use 1234567890 as the WEP key value Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com 8

9. Enable WEP On the PC using the Wireless Settings Change the SSID to CCNP Enable WEP Authentication Use 1234567890 as the WEP key value Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com 9

10. Configure the Web Server On the Web Server Open the Desktop tab Click the IP configuration icon Change the static settings of the Web Server as follows Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com 10

11. Configure the Web Server Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com 11

12. Configure the Web Server Open the Config tab disable all service except for HTTP and HTTPS Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com 12

13. Configure the Web Server Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com 13

14. Check Connectivity Open the wireless host’s Web Browser and verify that you can access the web server using the IP address 192.168.0.11 If you are successful, your browser page should look this Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com 14

15. Check Connectivity Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com 15

16. Enable WPA with TKIP WEP was replaced by WPA using TKIP Let’s see how WPA works On the wireless access point, enable WPA-PSK authentication Set the Data Encryption type to TKIP Use the PassPhase abcd1234 Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com 16

17. Enable WPA with TKIP On the wireless host, enable WPA-PSK authentication Use the PassPhase abcd1234 Ensure that the Data Encryption type is set to TKIP Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com 17

18. Check Connectivity After the wireless connection between the access point and the wireless host is resumed Verify connectivity by pinging the web server at 192.168.0.11 Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com 18

19. Enable WPA with AES TKIP was soon replaced in WPA by AES Let’s see how this change is made On the wireless access point, enable WPA-PSK authentication Set the Data Encryption type to AES Use the PassPhase abcd1234 Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com 19

20. Enable WPA with AES On the wireless host, enable WPA-PSK authentication Ensure that the Data Encryption type is set to AES Use the PassPhase abcd1234 Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com 20

21. Check Connectivity After the wireless connection between the access point and the wireless host is resumed Verify connectivity by pinging the web server at 192.168.0.11 Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com 21

22. Enable WPA2 There are two versions of WPA2 –WPA2-PSK –WPA2-Enterprise We have just seen WPA-PSK enabled above at all it is is WPA with TKIP replaced by AES In other words PSK or pre-shared key As in WEP and WPA, WPA-PSK is just a password based system Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com 22

23. Enable WPA2 As is true of any password based system, the password can be lost This requires all the devices be changed A better solution is to use a RADIUS server to enable WPA2-Enterprise Let’s see how this is done Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com 23

24. Configure the RADIUS Server Open the Desktop tab on the RADIUS Server and click the IP configuration icon Change the static settings of the RADIUS Server as follows Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com 24

25. Configure the RADIUS Server Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com 25

26. Configure the RADIUS Server Open the Config tab –Disable all services except AAA Click on the AAA service –Turn the AAA service on and leave the RADIUS port set to 1645 –Add a RADIUS client Linksys Access Point with an IP address of 192.168.0.1 and a secret key ccnp1234 –Add a user student with a password cisco Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com 26

27. Configure the RADIUS Server Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com 27

28. Configure the Access Point On the access point –Change the Authentication type to WPA2 –Configure the RADIUS server IP address as 192.168.0.10 –Set the Shared Secret key to ccnp1234 –Set the Data Encryption Type to AES Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com 28

29. Configure the Access Point Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com 29

30. Configure the Wireless Client On the Wireless Client –Change the Authentication Type to WPA2 Change the Data Encryption Type to AES –Enter the User ID student –Enter the password cisco Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com 30

31. Check Connectivity You should now have connectivity between the wireless host and the access point Verify this by connecting to the web server from the browser on the wireless host If you do not have connectivity to the web server, double-check all of your settings on access point, wireless host, and RADIUS server Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com 31

32. Source Most of this lab is stolen from John Morgan, but its ok, he said I could Copyright 2011 Kenneth M. Chipps Ph.D. www.chipps.com 32