Presentation is loading. Please wait.

Presentation is loading. Please wait.

Doing The Drafting Thing IE 1225 R. Lindeke. See next slide for variations from text! Lets begin with 1-2 “Box Part” – with some Variants & Dimensions!

Similar presentations


Presentation on theme: "Doing The Drafting Thing IE 1225 R. Lindeke. See next slide for variations from text! Lets begin with 1-2 “Box Part” – with some Variants & Dimensions!"— Presentation transcript:

1 Doing The Drafting Thing IE 1225 R. Lindeke

2 See next slide for variations from text! Lets begin with 1-2 “Box Part” – with some Variants & Dimensions!

3 Dimensions & Variations to add: Overall Size of Baseplate: 120x80x20th Notch in Base: 40w x 20h Overall Height: 70 (10thick x 50 h upper wall) Stiffener is 1mm at full wall height Leg Slots: 20w x 10d Add: Counterbored (12.5  x5d) 7.5  through hole centered on base plate

4 Entering the Drafting WorkBench Click START … Mechanical Design … Drafting

5 Setting up the Environment If NOT ANSI Size C click Modify and change it!

6 Click “View Creation Wizard”

7 Choose “Configuration 1” ICON

8 Click Next – Select ‘Perspective’ ICON and Position in Upper Right After finishing this – notice message – “Select a reference plane on a 3-D Geometry” asks you to go to the part of interest (use Window icon and click on the Box design); Once in the Part Design Get an acceptable Perspective view then click the top of the plate or one side

9 I chose the ‘Side of the Box’ as my 3-D view Notice the Blue Compass – clicking on the arrowheads or the curved arrows changes the image in the 3 views (perspective is as left in the Part Design environment)

10 Once you are satisfied with the views and you click on Front View you have this:

11 Adding a TitleBlock & Frame Click Edit … Sheet Background Then Insert … Drawing…Titleblock & Frame

12 While its “Blue” We can edit the Titleblock ‘at will’! Change Dassault … name to: UMD MIE Engineering Change Drw by to Your Name We will work on Scale Problem Later (anticipate that it is about half of what the drawing scale is – more later) In the “Empty Block” Click the T Icon and enter a part name and “Not ot Scale” then position and size

13 During Editing Set the Font Size with drop down box at top of image: When moving Text Boxes, Click on the Box and Hold Down SHIFT key to accurately position (when satisfied, release Mouse button 1 st ) Font Control

14 After Edit … Working Views RightClick on Isometric View “Border” and Properties We change view’s scale and appearance here with Whole num. ratios and click boxes

15 RightClick on Isometric View “Border” and View Positioning … “Position Independent …” Since the Isometric view is “non-critical” it can be positioned independently – the same is not true for Top and Rt. Side Views! Use the Mouse Button to Draw Views – on their borders

16 After Setting View Properties (scale 3:2?) then: Hide The View Notes “Right Click” the Text Box then click Hide/Show

17 Next We Add Dimensions: We will use Linear; Stacked; and Diameter Dimensions in this exercise … Along with some special symbols and text notes!

18 Linear Dimensions On a Single View Used Stacked Dimensions for Several offsets in Front and Rt. Side Views – they make good arrangement! Set Font size to 7.0 mm for all dimensions

19 Dimension Counter Bored Hole – Diameter dimension for through size and a text box with special characters for the Counter Bore Pull Down “Special Symbols” Icon (top of window) click: Counterbore & 12.5 … return then: Depth & 5, Set Font Size to 7

20 Next We want a Section View – We will “Slice” through the Box center Section Views can only be made from the Active View – Since Rt. Side view gives us the best choice, Highlight it and make it active! Its border turns Red and its name in Process Tree underlines – indicating active view

21 Finally a Balloon attached to Stiffener & Text Notes:

22 Preparing for Printing: Check all Info is Correct Rt. Click each View Border and Properties … Unclick “Display View Frame”

23 Preparing for Printing: Fix the Main Scale (to about half of what we set!) on the Title Block Click: File … Print Change Properties to Rotate 90; Fit a Page Click Page Setup and All Margins 1/10” (2.54 mm) Be sure to Preview before Sending to the Printer!!!

24 After Print Preview – a dimension (height) must be moved!

25 Some General Notes About Printing a Drafter Print: Scale is “Strange”! I set front and section views to 3:2, Isometric view to 0.5:1 when I printed the “Faked” C-size drawing to Letter paper my measured scale was about 0.75:1! So, I edit the title box to reflect the “actual scale” which is about half of that automatically set during sizing exercise Fonts in Dimensions needed to be increased to about 7.000 mm – space permitting – Same for Text Notes Turn off View borders before printing – in Right Click View … Properties – uncheck the box!


Download ppt "Doing The Drafting Thing IE 1225 R. Lindeke. See next slide for variations from text! Lets begin with 1-2 “Box Part” – with some Variants & Dimensions!"

Similar presentations


Ads by Google