2. Parallel JPEG2000 Compression System Performed by: Dmitry Sezganov, Vitaly Spector Instructor: Stas Lapchev, Artyom Borzin

3. Abstract Imaging satellites are experiencing rapid growth in imaging capacity. This is leading to higher data rates, and driving an increase in on-board storage capacity and downlink capability. Image compression is an excellent solution for this problem. By reducing the size of the image data, the overall system performance is improved. It must be high rate, since compression must be done prior to storage to reduce storage capacity. Typical image data rates are several Gbits per second, so the compressor must operate at speeds on the order of several hundred Mbits per second.

4. Abstract JPEG2000 Encoder JPEG2000 Decoder

5. Environment The system is implemented on the following platforms: Virtex-II Pro Development Board; ADV202 JPEG2000 Video Codec; PC Simulation;

6. Project Requirements The purpose of this project is building a prototype of parallel JPEG2000 compression system. The following list outlines the highest abstraction level requirements: Minimal input data rate is about 1.5Gbps. A user can choose different data source for system input. Defining compression parameters: 1.Tile/Image size. 2.Reversible/Irreversible compression mode. 3.Bit rate control with user defined rate/quality levels.

7. Project Requirements The system should report progression status (percentage, errors, etc.). Debugging capabilities – system architecture must support debug modules on each abstraction level, gathering information from child units in run-time for statistical analysis (revealing system bottlenecks, debug information). The resulting compressed output stream have to be saved to disk for system verification purposes (compressed images may be displayed in GUI).

8. Architecture Channel #1Channel #2 Testing Module Compression Unit There is a need of simulation data input stream with defined high bit rate, which cannot be obtained directly from the PC. That’s why we are going to use another board that will provide this channel.

9. Architecture Channel #1 may be implemented using standard Ethernet PCI card. Channel #2 requires high data rates and therefore two boards must communicate through Rocket IO ports in two directions enabling 2.5 Gbps efficient throughput. Needed speeds are not achievable upon data Channel #1. To solve this problem one picture could be loaded to the Testing Module and then duplicated to generate a needed bit rate. Channel #1Channel #2 Testing Module Compression Unit

10. Architecture PC Logic Memory ADV202 Testing Board Compression Board Codec Card Loading image through Ethernet Duplicating and sending image through Rocket I/O channel Tiled image data Bus Data flow

11. Architecture Function() send_packet() Ethernet driver Ethernet card PC Ethernet Controller PowerPC SDRAM Controller CallBack() Testing Board UART Controller ApplicationConsole COM Port SDRAM

12. Architecture Testing Board Rocket I/O PowerPC Codec Controller Compression Unit Rocket I/O Controller ADV202 PowerPC Rocket I/O SDRAM SDRAM Controller ADV202 ….

13. Testing Board Design The Virtex-II Pro development board does not have built-in Ethernet port. Expansion communication card will be used. Required signals are assigned to appropriate pins in Virtex-II Pro FPGA.

14. Testing Board Design DRAM (external memory) OPB Bus PLB Bus PPC405 BRAM_IF_C NTRL BRAM PLB2OPB_BR IDGE GPIO OPB2PLB_BR IDGE UARTLITEETHERNET Interrupt Controller Rocket I/O

15. Current Status Learning ADV202 Codec: features, operation modes, etc. Tools for development of embedded systems. Learning Virtex-II Pro Development Board – modifying existing working program. Integrating Ethernet controller to existing project and writing source code which operates its driver.

16. Plans and Times Finish integrating the Ethernet Controller and establish full duplex connection between the PC and the Testing Board – 1 week. Designing the Compression Board + exact definition of all data protocols (Ethernet, Rocket I/O) – 2 weeks. Developing detailed Codec Card design – 1.5 weeks. Drawing Codec Card ORCAD layout – 2 weeks. Total: 6.5 weeks at 50% confidence level (+ 2.5 weeks for unpredictable difficulties)