1. 1Kazi Spring 2008 CSCI 660 CSCI-660 Introduction to VLSI Design Khurram Kazi

2. 2Kazi Spring 2008 CSCI 660 Selecting a Semiconductor vendor One of the first things that needs to be done when designing a chip is to select the semiconductor vendor and technology one wants to use. The following issues need to be considered during the selection process Maximum frequency of operation Power restrictions Packageing restrictions Clock tree implementation Floor planning Back-annotationsupport Design support for libraries, megacells, and RAMs Available cores Available test methods and scans

3. 3Kazi Spring 2008 CSCI 660 Understanding the library Design Compiler (DC) uses these libraries Technology libraries Symbol libraries DesignWare libraries

4. 4Kazi Spring 2008 CSCI 660 Technology libraries Contain information about the characteristics and functions of each cell provided in a semiconductor vendor’s library. The manufacturers maintain and distribute the technology libraries Cell characteristics include information such as cell name, pin names, area, delay arcs and pin loading. The technology library also defines the conditions that must be met for a functional design (e.g., the maximum transition time for nets). These conditions are called design rule constraints. Also specify the operating conditions and wire load models specific to that technology DC requires the technology libraries to be in “.db” format. These libraries are typically provided by the semiconductor manufacturer

5. 5Kazi Spring 2008 CSCI 660 Symbol libraries Symbol libraries contain definitions of the graphic symbols that represent library cells in the design schematics. Semiconductor vendors maintain and distribute the symbol libraries. Design Compiler uses symbol libraries to generate the design schematic. You must use Design Vision to view the design schematic. When you generate the design schematic, Design Compiler performs a one-to-one mapping of cells in the netlist to cells in the symbol library.

6. 6Kazi Spring 2008 CSCI 660 DesignWare Library A DesignWare library is a collection of reusable circuit- design building blocks (components) that are tightly integrated into the Synopsys synthesis environment. DesignWare components that implement many of the built- in HDL operators are provided by Synopsys. These operators include +, -, *,, =, and the operations defined by if and case statements. You can develop additional DesignWare libraries at your site by using DesignWare Developer, or you can license DesignWare libraries from Synopsys or from third parties.

7. 7Kazi Spring 2008 CSCI 660 Specifying Libraries Use dc_shell variables to specify the libraries used by the Design Compiler as shown in the table below

8. 8Kazi Spring 2008 CSCI 660 Target Library Design Compiler uses the target library to build a circuit. During mapping, Design Compiler selects functionally correct gates from the target library. It also calculates the timing of the circuit, using the vendor-supplied timing data for these gates. Use the target_library variable to specify the target library. The syntax is set target_library my_tech.db

9. 9Kazi Spring 2008 CSCI 660 Link Library Design Compiler uses the link library to resolve references. For a design to be complete, it must connect to all the library components and designs it references. This process is called linking the design or resolving references. During the linking process, Design Compiler uses the link_library system variable, the local_link_library attribute, and the search_path system variable to resolve references The syntax is set link_library {* my_tech.db}

10. 10Kazi Spring 2008 CSCI 660 Specifying DesignWare Library You do not need to specify the standard synthetic library, standard.sldb, that implements the built-in HDL operators. The software automatically uses this library. If you are using additional DesignWare libraries, you must specify these libraries by using the synthetic_library variable (for optimization purposes) and the link_library variable (for cell resolution purposes).

11. 11Kazi Spring 2008 CSCI 660 Describing environmental attributes set_max_capacitance Set_max_transition & set_max_fanout on Inputs and Output ports or current design set_operating_conditions on the whole design

12. 12Kazi Spring 2008 CSCI 660 Environmental attributes Design environment consists of defining the process parameters, I/O port attributes, and statistical wire load models. Set_min_library -min_version dc_shell> set_min_library “ex25_worst.db” \ -min_version “ex25_best.db” This command allows the users to simultaneously specify the best case and worst case libraries. Can be used to fix set up and hold violation. The user should set both the min and the max values for the operating conditions

13. 13Kazi Spring 2008 CSCI 660 Setting operating conditions set_operating_conditions Specifies the process, voltage and temperature conditions of the design. Synopsys library consists of WORST, TYPICAL and BEST cases. Each vendor has their own naming convention for the libraries! Changing the value of the operating condition command, full range of process variations are covered.

14. 14Kazi Spring 2008 CSCI 660 Setting operating conditions set_operating_conditions WORST is generally used during pre-layout synthesis phase to optimize the maximum set-up time. BEST is normally used to fix any hold violations. TYPICAL is generally not used since it is covered when both WORST and BEST cases are used.

15. 15Kazi Spring 2008 CSCI 660 Setting operating conditions set_operating_conditions It is possible to optimize the design with both WORST and BEST cases simultaneously dc_shell> set_operating_conditions WORST dc_shell> set_operating_conditions –min BEST -max WORST

16. 16Kazi Spring 2008 CSCI 660 Operating conditions

17. 17Kazi Spring 2008 CSCI 660 Modeling wire loads DC uses wire loads models to estimate capacitance, resistance and the area of the nets prior to floor planning or layout. The wire load model is based upon a statistically average length of a net for a given fan out for a given area “10 x 10” “20 x 20”

18. 18Kazi Spring 2008 CSCI 660 Wire load command DC uses wire load information to model the delay which is a function of loading Synopsys provides wire load models in the technology library, each representing a particular size. Designer can create their own wire load models for better accuracy set_wire_load_model –name dc_shell>set_wire_load_model –name MEDIUM

19. 19Kazi Spring 2008 CSCI 660 Wire load mode There are 3 modes associated with the set_wire_load_mode: top, enclosed and segmented top Defines that all nets in the hierarchy will inherit the same wire load model as the top level block. Use it if when the plan is to flatten the design later for layout. enclosed Specifies all the nets (of the sub-blocks) inherit the wire load model of the block that completely encloses the sub-blocks. For example, if blocks X and Y are enclosed within block Z, then the blocks X and Y will inherit the wire load models defined for block Z.

20. 20Kazi Spring 2008 CSCI 660 Wire load mode segmented Used when wires are crossing hierarchical boundaries. From the previous example, the sub-blocks X and Y will inherit the wire load models specific to them, while nets between sub-blocks X and Y(which are contained within Z) will inherit wire-load model specified for block Z Not used often, as the wire load models are specific to the net segments set_wire_load_mode dc_shell>set_wire_load_mode top Accurately using wire load models is highly recommended as this directly affects the synthesis runs. Wrong model can generate undesired results. Use slightly pessimistic wire load models. This will provide extra time margin that may be absorbed later in the test circuit insertion or layout

21. 21Kazi Spring 2008 CSCI 660 Wire load models across hierarchy 50x50 20x20 40x40 30x30 50x50 20x20 40x40 50x50 30x30 50x50 20x20 40x40 30x30 mode = top: (ignores lower level wire loads) mode = enclosed: (uses best fitting wire loads) mode = segmented: (uses several wire loads) 30x3020x20

22. 22Kazi Spring 2008 CSCI 660 set_drive set_drive is used at the input ports of the block. It is used to specify the drive strength at the input port. Is typically used to model the external drive resistance to the ports of the block or chip. 0 signifies highest strength and is normally used for clock or reset ports. set_drive dc_shell> set_drive 0 {clk rst}

23. 23Kazi Spring 2008 CSCI 660 set_driving_cell set_driving_cell is used to model the drive resistance of the driving cell to the input ports. set_driving_cell –cell -pin dc_shell>set_driving_cell –cell BUFF1 –pin Z [all_inputs]

24. 24Kazi Spring 2008 CSCI 660 set_load set_load sets the capacitive load in the units defined in the technology library (pf), to the specified ports or nets of the design. It typically sets capacitive loading on output ports of the blocks during pre-layout synthesis, and on nets, for back annotating the extracted post layout capacitive information set load dc_shell>set_load 1.5 [all_outputs] dc_shell> set_load 0.3 [get_nets blockA/n1234]

25. 25Kazi Spring 2008 CSCI 660 Design rule constraints Design rule constraints consist of set_max_transition, set_max_fanout and set_max_capacitance. These rules are technology dependent and are generally set in the technology library. The DRC commands are applied to input ports, output ports or on the current_design. It can be useful if the technology library is not adequate of is too optimistic, then these commands can be used to control the buffering in the design set_max_transition set_max_capacitance object list> set_max_fanout,value> dc_shell –t>set_max_transition 0.3 current_design dc_shell –t>set_max_capacitance 1.5 [get_ports out1] dc_shell –t>set_max_fanout 3.0 [all_outputs] (dc_shell –t> corresponds to DC operating in tcl mode)

26. 26Kazi Spring 2008 CSCI 660 Some more design constraints dc_shell –t >create_clock –period 40 -waveform [list 0 20] CLK set_dont_touch_network is a very useful command and is usually used for clock and reset. It is used to set_dont_touch property on a port, or a net. This prevents DC from buffering the net in order to meet DRCs. dc_shell –t>set_dont_touch_network {clk, rst}

27. 27Kazi Spring 2008 CSCI 660 Some more design constraints If a block generates a secondary clock from the primary, e.g. byte clock from the serial clock, in this apply set_dont_touch_network on the generated clock output port of the block. Helps prevent DC from buffering it up. Clock trees can later be inserted to balance the clock skew.

28. 28Kazi Spring 2008 CSCI 660 Some more design constraints set_dont_touch is used to set a dont_touch property on the current design, cells, references or net. This is frequently used during hierarchical compilations of the block. dc_shell –t>set_dont_touch current_design Useful in telling DC not to touch the current design if it has been optimized to designer’s satisfaction. For example, if some spare gates block is instantiated, DC will not touch it or optimize it.