1. Takashi Endo Director General, Technical Planning Dept. and Research and Development Center East Japan Railway Company

2. Contents 1. Shinkansen Speed Increase Target and Objectives 1-1. JR East Shinkansen Network 2 ． Speed Increase Challenges 2-2. High-speed Test Train Fastech 360 S 1-3. Speed Increase Objectives 2-1. Shinkansen Speed Increase Project 1-2. Worldwide High-speed Railways 4. Future Direction 3 ． Issues and Measures for the Realization of Speed Increase 3-1. Running Speed Increase 3-3. Environmental Compliance 3-2. Ensuring Reliability 3-4. Comfort Improvement 5. Conclusion

3. Eco-friendliness Long nose （ 16m ） Optimized nose shape (comparison of two different shapes) Reduced micro-pressure waves in tunnels Stream-line Arrow-line Smaller car body sectional area 3700mm3650mm Red ： E2 Series Sectional area 11.2m 2 Blue ： E954 Series Sectional area 10.8m 2 Pantograph with multi-split slider to support current collection at high speeds Assuring high-speed current collection performance Reduced noise Pantograph noise insulation panel Current collection using only one pantograph per trainset New low-noise pantograph Sound-absorbing under-floor structure Smoothing of all car body parts High-output,compact,lightweight and low noise main circuit system Running wing-cooled and water-cooled main converter Permanent magnet synchronous motor Running wind-cooled main transformer Quieter cabin Noise insulating windows Floating floor construction Planned passenger compartment design for the near future Reliability assurance Preventing snow hazards Car body shape inhibits snow from sticking Improved brake performance,shorter emergency braking distance Devices to increase air resistanceImproved disc brakes Cohesion increasing device (Ceramic particle sprayer) Air spring strong car body tilting system(2˚) Solenoid actuator type oscillation absorption system (Active suspension) Preventing car body oscillation Control unit Improved bogie riding comfort characteristics (Comparison of three different types of bogies ) Improved riding comfort through curves Assuring reliability of running components Highly reliable,low noise driving devices Axle bearings that support high speeds Actual load endurance tests Faster running speeds Greater comfort Fastech 360 S : Overview

4. Fastech 360 S : Table of principal specifications 12345678 E954-1E954-2E954-3E954-4E954-5E954-6E954-7E954-8 T1cM1M2 M1sM2M1T2c Measurement2nd class Measurement1st class2nd class Measurement Car body construction Nose shape 16m streamline 16m arrowline Type Principal dimensions Gear ratio Axle box suspension Electrical system Current-collecting system Single-arm, low-noise pantograph Single-arm, low-noise pantograph Control system Traction motor Brake system Primary brake Air compressor Axle beam system AC 50Hz, 25,000V VVVF inverter control (with train-set torque control) Synchronous motor3-phase, induction motor Coupling with Shinkansen High-Speed test Train Type E955 (preparatory work under way for No.1 car) 2-frequency ATC and DS-ATC LCX radio; yard protection radio Device for increasing aerodynamic drag; device for increasing adhesion Electric command brake equipment with regenerative brake (with control to restore adhesion in case of wheel slip, load compensating control, train-set braking force control) Center-clamped brake disk, pneumatic caliper system Combination air conditioner and ventilator; cooling 74.4 kw, heating 40 kw Screw type 370 kw x 8 units355 kw x 8 units370 kw x 8 units Wheel diameter 860 mm, wheelbase 2,500 mm (distance between bogies : 17,500 mm) 2.45 Axle beam systemSuspension plate system Length 25,000 mm x width 3,380 mm x height 3,650 mm(leading car body length : 27,500 mm) Aluminum alloy double-skin construction Bolsterless bogie with car body tilting system of air spring stroke type Car number Type Average 11.5 t or less; maximum 12.5 t or less 360 km/h (405 km/h is attainable with 820 mm-diameter wheels) Other equipment Car principal dimensions Maximum operating speed Axle load Air-conditioning equipment Coupling function Safety equipment Train radio Car body Bogie Main circuit Brake

5. Conclusion JR East aims for worldwide first class standard for the next generation of Shinkansen, in terms of speed, comfort, reliability and harmony with the environment. To comprehensively assess and verify development technology in the real environment and under actual conditions, JR East completed the development of a high-speed test train exclusively for this purpose and is now implementing running tests. All functions verified in the high-speed tests will be compiled as a mass production specification and will be used to create the next generation of Shinkansen railcar. 1 3 2