1. Pacemaker troubleshooting-single chamber pacemakers

2. Reasons for evaluation
Patient symptomatic
Palpitation
Syncope
presyncope
Pacemaker malfunction suspected
ECG
Telemetry
Ambulatory ECG
Routine pacemaker follow up

3. Patient details Indication for pacing Implant operative note Diagnosis
Medication –can alter pacing tresholds
DC ,MRI,electrocautery
Trauma,electrical current exposure
Concurrent medical problems-CRF,hyperkalemia
Prior ECG,CXR

4. Pacemaker system manufacturer Model current programming
date of implant
special features
Sensing and pacing tresholds
impedance

5. Lead system
manufacturer
model
polarity
Fixation
insulation and date

6. Causes of pacemaker malfunction
CorePace Module 4: Troubleshooting
Causes of pacemaker malfunction
Pacing stimuli present with failure to capture
Pacing stimuli present with failure to sense
Pacing stimuli absent
Oversensing
No output
Pseudomalfunction

7. Failure to capture No evidence of depolarization after pacing artifact
CorePace Module 4: Troubleshooting
Failure to capture
No evidence of depolarization after pacing artifact
loss of atrial capture, followed by a scheduled ventricular pace. Following , the marker channel recorded an intrinsic P-wave.
Loss of capture

11. Early post device implantation
CXR abnormal
Lead dislodgement
Downward migration of PG
Failure to secure anchoring sleeves properly
Too little or too much slack
Lead perforation
Elevated impedance
Loose set screw
failure to seat lead pin properly in header
Normal CXR,normal impedance
Micro lead dislodgement
Inflammatory response

12. Late post device implantation
Battery depletion
Twiddler s syndrome
Abnormal myocardium
Insulation failure
Conductor failure
Mechanical stress on lead
Anchoring sleeve
Interaction with generator in pocket
b/w clavicle and first rib

13. Increase the energy in the output pulse
Run a capture threshold test
Adjust the output parameters, if necessary
Pulse amplitude (V)
Pulse width or duration (ms)
It is generally more efficient to increase the pulse amplitude
Investigate possible lead problems
Reprogram device polarity

14. CorePace Module 4: Troubleshooting
Undersensing
An intrinsic depolarization that is present, yet not seen or sensed by the pacemaker
An intrinsic depolarization occurs in the atrium, but this depolarization is not sensed by the pacemaker. Therefore, the pacemaker sends an inappropriate pacing pulse to that chamber. Undersensing “overpacing.”
In this example, an AAI pacemaker is programmed to inhibit the atrial pacing pulse when a P-wave is sensed. Because the P-wave was not sensed, the pacemaker delivered an atrial pulse. If a pacemaker is undersensing, you will not see appropriate atrial sense markers on the marker channel.
P-wave not sensed
Atrial Undersensing

15. Undersensing occurs when the pacemaker does not detect intrinsic activity that really is there
Undersensing causes the pacemaker to pace more than it should

19. Undersensing May Be Caused By:
CorePace Module 4: Troubleshooting
Undersensing May Be Caused By:
Inappropriately programmed sensitivity
Lead dislodgment
Lead failure:
Insulation break; conductor fracture
Lead maturation
Change in the native signal
Functional
Magnet
Noise reversion
Insulation breaks may cause undersensing if the insulation break results in the:
Reduction of intrinsic beats at the sense amplifier
Inability of the amplitude to meet the sensitivity requirement
Conductor fracture may cause an open circuit. If intrinsic signals cannot cross the conductor fracture, undersensing will occur. The primary cause of conductor fracture is the chronic stress imposed on the lead as a result of its placement in the subclavian region, and may be reflected in increased impedance readings.
During the first week following lead implantation, the amplitude and slew rate may abruptly decline; these values increase to approach implantation values after about 6-8 weeks as the lead matures.1 (Steroid-eluting leads may eliminate the reduction in sensitivity by minimizing the growth of fibrotic tissue near the electrode).
Lead dislodgment usually occurs early in the life of the pacemaker before the lead has fibrosed to endocardial tissue. The primary causes of lead dislodgment are:
Inadequate initial positioning
Patient movement (bringing arms overhead, etc.)
Secondary intervention rates for lead dislodgement should be below 2% for ventricular leads and 3% for atrial leads.2 One recent clinical trial reported a lead dislodgement rate of 2.2%.2
Changes in the native signal may be caused by:
Myocardial infarction
Change in medications (not common)
Electrolyte imbalance
Undersensing may be caused by an inappropriately programmed setting.
1Hayes DH. Cardiac Pacing and Defibrillation: A Clinical Approach. Armonk, NY: Futura Publishing Company; Page 453.
2Link MS et al. Complications of dual chamber pacemaker implantation in the elderly. Pacemaker Selection in the Elderly (PASE) Investigators. J Interv Card Electrophysiol. 2: , 1998.

20. Adjust the sensitivity setting
Run a sensing threshold test
Measure the intrinsic signals
Adjust the sensitivity appropriately
To increase sensitivity, decrease the mV setting
Make all changes to sensitivity settings in small steps since large changes may only introduce new sensing problems

22. Oversensing The sensing of an inappropriate signal
CorePace Module 4: Troubleshooting
Oversensing
...Though no activity is present
Marker channel shows intrinsic activity...
Ventricular Oversensing
If a pacemaker is oversensing, you will see signals on the marker channel that do not correspond to the ECG pattern. In this example, the pacemaker recorded a ventricular pulse on the marker channel. However, no activity was demonstrated on the ECG strip. Pauses or intervals longer than the programmed lower rate will occur in single chamber systems. Dual chamber systems may show tracking at the upper rate with atrial oversensing.
Lead insulation failure (a decrease in lead impedance will be seen)
Make-and-break fracture
A lead connection problem
Insulation failure—a common cause of oversensing—occurs when myopotentials are detected at the site of the insulation break. Lead fracture is another common cause of oversensing. As the frayed ends of conductor wires “make and break” contact, the pacemaker senses these “make and break” signals, which results in oversensing.
Oversensing may also occur if the lead is loose in the connector block.
The sensing of an inappropriate signal
Can be physiologic or nonphysiologic

23. Oversensing occurs when the pacemaker inappropriately “thinks” that it sees intrinsic activity that is not there
Oversensing causes the pacemaker to inhibit the pacing output pulse, even though the device should be pacing

26. Oversensing of normal intracardiac signals
Myopotentials
Pectoralis,rectus abdominis,diaphragm
Bipolar leads are less susceptible
Oversensing of normal intracardiac signals
Reduce sensitivity of affected lead to eliminate oversensing
EMI
Provocative maneuvers may be needed if intermittent symptoms
Magnet eliminates pauses-oversensing

27. Reprogram the sensitivity
Conduct a sensing threshold test
Adjust the sensitivity by making the device less sensitive (increase the mV setting)
Make only small changes
Extend the refractory period

28. CorePace Module 4: Troubleshooting
No Output
Pacemaker artifacts do not appear on the ECG; rate is less than the lower rate
When the pacemaker problem is no output, the marker channel shows pacing markers—AP or VP—although no artifact appears on the ECG.
No output is defined as the failure to pace. Impulses are generated from the IPG, but is not transferred to the lead.
Pacing output delivered; no evidence of pacing spike is seen

30. No Output May Be Caused By:
CorePace Module 4: Troubleshooting
No Output May Be Caused By:
Poor connection at connector block
Lead failure
Battery depletion
Circuit failure
A poor connection at the connector block can result in a lack of output, which can prevent the pacemaker from delivering a pacing pulse.
In addition to lead dislodgment, lead perforation should be considered with acute implants as a potential cause of noncapture.
Battery depletion can result in a lack of output, which can prevent the pacemaker from delivering a pacing pulse.
At generator replacement procedures, (and sometimes at initial implants) the pacemaker pocket may be malformed or too large to accommodate the pacemaker. Air can get trapped in the pocket which, with unipolar devices, will not allow appropriate grounding. No output can result.
Circuit failure—more commonly referred to as “pacemaker malfunction”—is very rare.

31. Steps to take for possible loss of output
Verify all lead connections
Check lead integrity
Evaluate battery status
Contact the device manufacturer
Loss of output may require the replacement of all or part of the pacing system

32. Pseudomalfunctions Pseudomalfunctions are defined as:
CorePace Module 4: Troubleshooting
Pseudomalfunctions
Pseudomalfunctions are defined as:
Unusual,Unexpected ECG findings that appear to result from pacemaker malfunction but that represent normal pacemaker function
Pseudomalfunctions should be ruled out as the cause(s) of an anomalous ECG strip before corrective measures are taken.

33. Hysteresis
Magnet rate
rate responsive pacing
Noise reversion
Rate drop response
Sleep rate algorithm

34. CorePace Module 4: Troubleshooting
Hysteresis
Allows a lower rate between sensed events to occur; paced rate is higher
Hysteresis provides the capability to maintain the patient’s intrinsic heart rhythm as long as possible, while providing back-up pacing if the intrinsic rhythm falls below the hysteresis rate. Because hysteresis exhibits longer intervals between sensed events, it may be perceived as oversensing.
Hysteresis Rate 50 ppm
Lower Rate 70 ppm

35. CorePace Module 4: Troubleshooting
Magnet Operation
Magnet application causes asynchronous pacing at a designated “magnet” rate
Magnet operation varies within different product lines and from manufacturer to manufacturer, but will usually involve a rate change when the magnet is applied. The Threshold Margin Test (TMT) is part magnet operation for most of Medtronic’s devices. The following operation describes magnet operation and TMT for most Medtronic devices:
Three beats at 100 bpm, followed by a magnet rate of 85
The third beat has an automatic pulse width decrement of 25% (loss of capture would indicate that the stimulation safety margin is inadequate)
Dual chamber devices will shorten the AV delay to 100 ms
Elective replacement indicators will change the rate from 85 to 65 and the mode from dual to single chamber pacing
It is important to remember that magnet modes vary from manufacturer to manufacturer, and from device to device. While recent Medtronic devices use the above rule of thumb, many older devices used the programmed lower rate as the magnet rate, or would decrease the rate by a certain percentage as a battery depletion indicator.
Kappa devices have a feature called Extended TMT. Extended TMT is a programmable feature and will operate as follows: TMT is performed at 100 ppm with the pulse width reduced by 25% on the third pulse, 50% on the fifth pulse, and 75% on the seventh pulse. This type of operation is extremely useful in assessing adequate safety margins, by simply using a magnet.

36. Threshold Margin Test (TMT)
Three beats at 100 bpm, followed by a magnet rate of 85
Third beat has an automatic pulse width decrement of 25%
Elective replacement indicators-change the rate from 85 to 65
Extended TMT.
TMT is performed at 100 ppm
Pulse width reduced by 25% on 3rd , 50% on 5th , and 75% on 7th

37. Rate Responsive Pacing
CorePace Module 4: Troubleshooting
Rate Responsive Pacing
An accelerating or decelerating rate may be perceived as anomalous pacemaker behavior
If a patient is active it is easy to equate rate increases with rate responsive pacing. Some patients may experience “false positive” increases in rate from their sensors. In the case of a piezoelectric crystal, the pacemaker may begin pacing at a faster rate if, for example, the patient is either lying on the side that the pacemaker is implanted on or experiencing a bumpy car ride.
Minute ventilation sensors measure the change in respiration rate and tidal volume. If a patient experiences rapid respiration resulting from a cause other than exercise (e.g., hyperventilation), the pacemaker may begin pacing at a faster rate.
VVIR / 60 / 120

38. Electrical Reset and Battery Depletion
CorePace Module 4: Troubleshooting
Electrical Reset and Battery Depletion
Reset may occur due to exposure to EMI
electrocautery, defibrillation, causing reversion to a “back-up” mode
Rate and mode changes will occur
Device can usually be reprogrammed to former parameters
Elective replacement indicators (ERI) can resemble back-up mode
Interrogating device will indicate ERI (“Replace Pacer”)
Electrical reset, or “back-up,” modes are usually exhibited by a rate change and often by a mode change. a pacemaker may interpret the radiofrequency signal as an intrinsic event, which would result in inappropriate inhibition of a pacing pulse and could cause the pacemaker to revert to a back-up mode.
Defibrillation may damage both the pulse generator and cardiac tissue because it delivers a large amount of electrical energy in the vicinity of the pacemaker. If the pacemaker’s protective mechanisms are overwhelmed by defibrillation, the back-up mode will be activated.
Elective replacement indicators are often similar to back-up modes.

39. A Change in Pacing Modes May Be Caused By:
CorePace Module 4: Troubleshooting
A Change in Pacing Modes May Be Caused By:
Battery depletion indicators (ERI/EOL)
Electrical reset
Mode switching
Noise reversion
The Elective replacement indicator (ERI) is designed to alert the clinician at least three months before the battery voltage drops to a level at which noncapture or inconsistent pacing would result. The end of life (EOL) indication is designed to give the patient and physician adequate time to replace the device.
Battery depletion may necessitate a mode switch prior to battery failure. For example, the mode may be switched from DDD to VVI or from DOO to VOO.

40. CorePace Module 4: Troubleshooting
Noise Reversion
Sensing occurring during atrial or ventricular refractory periods will restart the refractory period. Continuous refractory sensing is called noise reversion and will:
Cause pacing to occur at the sensor-indicated rate for rate-responsive modes
Cause pacing to occur at the lower rate for non- rate-responsive modes
The portion of the refractory period after the blanking period ends is commonly called the “noise sampling period.” A sensed event in the noise sampling period will initiate a new refractory period and blanking period.

41. Noise reversion
VT in a patient with VVI-pacing occurs at lower rate due to noise reversion

42. Rate drop response
Delivers pacing at high rate when episodic drop in rate occurs

43. Muscle Stimulation May Be Caused By:
CorePace Module 4: Troubleshooting
Muscle Stimulation May Be Caused By:
Inappropriate electrode placement near diaphragm or nerve plexus
Break in lead insulation
Unipolar pacing
Diaphragmatic stimulation may occur because of inappropriate lead

44. Flouro diagnosis

49. 1.ECG shows A.Failure to sense B.Failure to capture C.Hysteresis
D.Oversensing

50. 2.ECG shows A.Failure to sense B.Failure to capture C.Hysteresis
D.Oversensing

51. 3.ECG shows A.Failure to sense B.Failure to capture C.Hysteresis
D.Oversensing

52. 4.ECG demonstrates a.Failure to sense b.Failure to capture
c.Functional non capture
d.fusion

53. 5 ECG shows A.Failure to sense B.Failure to capture C.Hysteresis
D.Functional non capture

54. 6 ECG shows A.Functional non capture B.Failure to capture C.Hysteresis
D.Oversensing

55. 7.possibilities are
A.VVI in VOO mode
B.magnet kept
C.persistent ventricular undersensing
D.Noise reversion

56. 8.make and break potentials usually cause
A.undersensing
B.oversensing
C.functional non capture
D.failure to capture

57. 9.elevated pacing threshold and elevated impedance can be caused by
A.lead fracture
B.loose set screw
C.insulation failure
D.battery depletion

58. 10.elevated threshold with decreased impedance caused by
A.lead fracture
B.loose set screw
C.insulation failure
D.battery depletion

59. 11. What are appropriate in this patient A
11.What are appropriate in this patient A.sensitivity setting to be adjusted B.lower the programmed rate C.introduce hysteresis D.check capture treshold

60. 12.What is the next step in this patient
A.adjust sensitivity-increase mV setting
B.adjust sensitivity-decrease mV setting
C.pacing treshold test-adjust output parameters
D.activate hysteresis

61. 13.What is appropriate in this patient
A.adjust sensitivity-increase mV setting
B.adjust sensitivity-decrease mV setting
C.pacing treshold test-adjust output parameters
D.activate hysteresis

62. 14.What is appropriate in this patient
A.adjust sensitivity-increase mV setting
B.adjust sensitivity-decrease mV setting
C.pacing treshold test-adjust output parameters
D.activate hysteresis

63. 15.What is appropriate in this patient
A.adjust sensitivity-increase mV setting
B.adjust sensitivity-decrease mV setting
C.pacing treshold test-adjust output parameters
D.activate hysteresis