1. A2 Pole Changeout Energized
© 2018 Iowa Association of Electric Cooperatives
DISCLAIMER: This job hazard analysis (JHA) has been made available for informational and educational purposes only. The IAEC does not make any representation or warranty with respect to the accuracy, applicability, fitness, or completeness of the JHA. The IAEC hereby disclaims any and all liability to any party for any direct, indirect, implied, punitive, special, incidental or other consequential damages arising directly or indirectly from any use of this JHA which is provided as is.

2. Why are we doing this energized?
Take some time to decide if it is necessary to do this job energized.
Could the job be done de-energized and grounded?
What would be the impact?
Would it be safer?

3. OSHA Required Tailgate Discussion Topics
Hazards Associate with the job
Work Procedures Involved
Special Precautions
Energy Source Controls
PPE Required
The five topics required by OSHA to discuss in the tailgate.
First letter from each topic = How Well Should Everyone Plan

4. Work Procedures Involved Hazards associated with the job
Special Precautions
Energy Source Controls
Personal Protective Equipment
Be sure to record your emergency location and post in a location everyone on the crew knows.
Have your PPE and First Aid kit available
Be sure your AED is accessible.
A safe job begins with a thorough inspection of…
Tools Be certain all of your tools are in good shape.
Equipment Make sure your trucks are all in working order take time to preflight your equipment and insure there are no surprise.
Line/Structure Look over the line and structure. Are there any potential hazards? (Broken insulators, damaged wire, clearances over roads or from trees?)
Be aware of your work area, be sure to cover anything you can reach touch or fall into. And anything that can reach touch or fall into you!
Discuss all PPE needed for the job and wear your PPE. Be sure to inspect your equipment prior to use. Identify all voltages you are exposed to. Be sure to have all of your Arc-Flash protective gear on.
Identify a dedicated observer
Working in traffic exposes you to hazards that are difficult to control. Give the vehicles plenty of time to see and avoid you! Follow the manual of traffic control for your area.
Slips trips and falls are some of the most common injuries, look for hazards that could cause this. Be sure to inspect and wear your fall arrest harness.
Here are the five topics again with signs and bubbles to jump start tailgate discussion!!
Click on the icon to bring up a text box. Click on the icon again to make the text box go away
Gets the crew involved. Gives the feeling of knowing it is ok to ask questions, give suggestions, see something, say something!
The next slides will get directly into the task at hand. Visual, written and audio will all be used here!
There are suggestions in the notes as to what to discuss. This will get the Team involved, creating communication channels to open!

5. Be sure to set the protective device to single shot
Be sure to set the protective device to single shot. Check the adjacent spans for hazards. Be sure you have completed your briefing.

6. Bond the truck to the system neutral.

7. Remove the ground connection to the pole.

8. Install cover-up to the neutral.

9. Untie and lower the neutral
Untie and lower the neutral. Be sure it is not in direct uninsulated contact with the pole.

10. Install line cover-up.

11. Place split blankets on the pole top
Place split blankets on the pole top. Be sure to pull it up snug to cover all of the pole top pins. Insure prior to untying the conductor you have positive control of the conductor. Once this is done you can untie the conductor. Be sure to keep your ties cut short.

12. Once the conductor is untied and clear of the insulator you can slide the cover-up together.

13. Raise or reposition the conductor to allow for the replacement of the insulator. You may take the neutral up as well. If this is done use an insulated link and roller.

14. Replace the pole. Be certain the ground crew keeps the new pole away from the line.

15. The ground crewmembers can install the split blankets for you.

16. Move the conductor into position.

17. Retie the conductor. Be careful not to make contact with the tails of the tie.

18. Remove the split blankets.

19. Remove the line cover-up.

20. Raise the neutral back up, remove cover-up, and tie it in.

21. Reconnect the ground wire.

22. Remove the truck bond.

23. Job completed.