1. Krzysztof Czuba ESS LLRF Quarterly Meeting 08.11.2018
Status of PEG
Krzysztof Czuba
ESS LLRF Quarterly Meeting

2. ESS PEG Progress Meeting, K. Czuba
Overall Schedule
On following slides there are no milestones related directly to Teststand (Task 7). Need separate discussion.
, Łódź
ESS PEG Progress Meeting, K. Czuba

3. ESS PEG Progress Meeting, K. Czuba
Milestones 1-21
# MS
Short description
Planned / Baseline date
Location
Responsible
Status/Comments 1
Kick-off meeting
WUT
Partner 2
Progress meeting
Every 3 months
ALL
Partner/ESS ERIC 3
Final System Architecture Specification
ESS ERIC 4
LO RTM PDR (Preliminary Design Review)
Closed by PDR in May 2017 5
Initial software from ESS ERIC for design verification 6
LO RTM first prototype finished
Partner 
Produced (CS-LOG) 7
Piezo Driver PDR (Preliminary Design Review) 8
Piezo Driver first prototype finished
DMCS 9
RTM Carrier AMC PDR (Preliminary Design Review) 10
RTM Carrier AMC first prototype finished
NCBJ
Produced 11
Final Solution from ESS ERIC for design verification 12
Cabling and Installation planning for M-Beta finished
Delayed – expected Q1-Q2 2019 13
Cabling and Installation planning for H-Beta finished 14
LO RTM M-Beta prototype
Produced and tested. 15
LO RTM for M-Beta CDR (Critical Design Review)
Done 16
Piezo Driver M-Beta prototype
Produced ( ) and tested with H-Beta 17
Piezo Driver for M-Beta CDR 18
RTM Carrier AMC M-Beta prototype
Produced 19
RTM Carrier AMC for M-Beta CDR 20
Cavity Simulator prototype and preliminary firmware
Ready. All Units shipped. 21
Cavity Simulator final firmware and documentation
, Łódź
ESS PEG Progress Meeting, K. Czuba

4. ESS PEG Progress Meeting, K. Czuba
Milestones 21-38
# MS
Short description
Planned / Baseline date
Location
Responsible 22
First LLRF control unit delivery to ESS ERIC Lund
ESS ERIC
Partner 23
LLRF System SAR (System Acceptance Review) 24
Delivery of COST components for M-Beta to Partner Facility
NCBJ
2019 25
Delivery of M-Beta units to ESS ERIC Lund
We need new installation schedule 26
M-Beta units installation finished
Linked to MS above 27
M-Beta SAT (Site Acceptance Test) 28
LO RTM H-Beta prototype
WUT 29
LO RTM for H-Beta CDR (Critical Design Review) 30
Piezo Driver H-Beta prototype
DMCS 31
Piezo Driver for H-Beta CDR (Critical Design Review) 32
RTM Carrier AMC H-Beta prototype 33
RTM Carrier AMC for H-Beta CDR (Critical Design Review) 34
Delivery of COST components for H-Beta to Partner Facility 35
44 H-Beta units delivered to ESS ERIC Lund 36
44 H-Beta units installation finished 37
H-Beta SAT (Site Acceptance Test) 38
Final Report Approved Review (SAR) and Final Report Approved
, Łódź
ESS PEG Progress Meeting, K. Czuba

5. ESS PEG Progress Meeting, K. Czuba
Milestones 39-56
# MS
Short description
Planned / Baseline date
Location
Responsible 39
Electron Pick-up CDR
ESS ERIC
Done 40
Delivery of Electron Pick-up Design from ESS ERIC
Design changed 41
Delivery of 38 (RFQ and Spoke) Electron Pick-ups with test reports
Partner
Postponed to March 2019 42
Delivery of 36 (MB) Electron Pick-ups with test reports
Probably will be delayed 43
Delivery of 44 (HB) Electron Pick-ups with test reports 44
Delivery of 36 Piezo Power Supplies 45
Delivery of 84 Piezo Power Supplies 46
RF Split Box CDR 47
Delivery of 87 RF Split Boxes (RFQ, MEBT, DTL, Spoke and MB) )
Delayed due to measurement problem and missing attenuator configuration from ESS. Investigations in progress 48
Delivery of 44 RF Split Boxes (HB) 49
PIN Diode CDR 50
Delivery of 81 PIN Diodes (RFQ, MEBT, DTL, Spoke and MB
Delayed 51
Delivery of 44 PIN Diodes (HB) 52
Delivery of 81 PSS Switches (RFQ, MEBT, DTL, Spoke and MB)
Production lauchd. Delivery expected Q1 2019 53
Delivery of 44 PSS Switches (HB) 54
Delivery of 120 Patch Panels
Delayed. Possible Q2 2019 55
Initial Firmware/Software delivery for the RTM Carrier 56
Final Firmware/Software delivery for the RTM Carrier
, Łódź
ESS PEG Progress Meeting, K. Czuba

6. Action List from CDR Module Description Responsible Status Due date
Details 1
RTM carrier, LO RTM
Finalise modifications
PEG
Done 2
All
Review prototype availability and production volumes
PEG/ESS
Draft
Quarterly meeting in Łódź
Including Freia and other TS, see separate doc 3
Piezo RTM
Confirm Fischer connector type
ESS/AJJ
Connector changed Fisher 103 4
Reconsider LED color coding
Piezo actuator green LED 5
Confirm Pz controller cable lengths for M-Beta and H-Beta
ESS
Not ready
End of Sept. 2018
Suggested meters. To be rechecked by ESS 6
Verify PSU cable length
See rack layout 7
Clarify Spoke Pz stack up
TBA
mid. 2019?
Not urgent 8
Share MB rack layout
ESS/ASV
Still needs some details 9
Use CHESS
General recommendation
10a QA
Add/update test&inspection plan
to be done
up to finishing of prototypes. October 16th
Concerns also prototypes. Review it on Quarterly meeting in October
10b
Add/update verification plan
up to finishing of prototypes
Review it on Quarterly meeting in October
10c
Add/update FAT document
, Łódź
ESS PEG Quarterly Meeting, K. Czuba

7. Module Description Responsible Status Due date Details11 CS
Test LLRF system with cavity and provide data
ESS
In progress
2 months after teststand 2 ready with M-Beta cavity
Needed for final CS design. Tests with H-Beta Cavity done in Freia 12
All
Update risk register
PEG/ESS
Quarterly meeting in Łódź
Current verson needs update. 13
Schedule replanning in August
Latest during Quarterly meeting in Łódź
14a
E-pickup
LED's inconsistence with LPS status
ESS/Bruno
Done
wk 35
14b
Review component placement 15
PIN diode
Verify how power outage will influence control signal
in progress ?? 16
E-pickup & PIN
Produce front panel layout for all combinations
PEG
Not ready
Wait for modifications of the PIN diode
Three different combinations 17
Provide configuration
, Łódź
ESS PEG Quarterly Meeting, K. Czuba

8. Make mechanical enclosure larger PEG/ESS Done Request by Morteza, PSS
Module
Description
Responsible
Status
Due date
Details 18
PSS switch
Make mechanical enclosure larger
PEG/ESS
Done
Request by Morteza, PSS
x31
SplitBox
Change mechanics to have rear connectors optimized for rack layout
PEG
ESS to review new proposal. MG will send the design and prototype in September
x32
Postpone delivery date (not time critical)
Discuss during the QM
To gain experience from TS2. PEG needs a list of attenuators.
x33
PIN diode
Switch diode outside spec at 352 MHz
ESS/Bruno
wk33
Perfomance is OK. Confirm with Bruno.
x34
Production test at 24V-10% (21.6V)
wk39
Update test specification. 3 pieces working at 17V.
x35
Decide if separate variants for 352 and 704 MHz
wk37
Seems that the same RF matching will be needed for both variants.
x36
Patch panel
Talk to ICS and LPS about card placement in MTCA Crate
ESS/ASV
In progress
end of 2018
Test rack in preparation
, Łódź
ESS PEG Quarterly Meeting, K. Czuba

9. Thank you for your attention
, Łódź
ESS PEG Progress Meeting, K. Czuba