1. Zonal & Station Identification Systems
Model S64F Helicopter
Rev. A Sept 18, 2007 2-

2. S64F
Rev. A Sept 18, 2007 2-

3. Airframe S-64F MAINTENANCE MANUAL, Pub. No. 3EAC006 Manual Organization
Manual Layout
Revision Record
List of Effective Pages
Table of Contents
Chapters
Chapter Locations
Chapter Organization
1. Chapter Table of Contents
2. Component Description
3. Servicing Instructions
4. Inspection
5. Removal
6. Disassembly
7. Assembly
8. Installation Instructions
Rev. A Sept 18, 2007 2-

4. Airframe S-64F MAINTENANCE MANUAL, Pub. No. 3EAC006 Manual Organization
VOLUME I
1. Aircraft General
2. Airframe
3. Alighting Gear
4. Power plants
5. Rotors
6. Drive Train System
VOLUME II
Hydraulic Systems
Instruments
Electrical Systems
Fuel Systems
Flight Controls
Utility Systems
Environmental Control Systems
Hoists and Winches
Auxiliary Power Plant
Emergency Equipment
Optional Equipment
Rev. A Sept 18, 2007 2-

5. Airframe S-64F MAINTENANCE MANUAL Pub. No
Airframe S-64F MAINTENANCE MANUAL Pub. No. 3EAC006 Manual Organization (Continued)
VOLUME II (continued)
Appendix A. Special Inspections
Appendix B. Consumable Maintenance Supplies and Material
Appendix C: Special Tools & Test Equipment
Electrical Schematic Manual
Separate from Maintenance Manual. -Aircraft Specific
Rev. A Sept 18, 2007 2-

6. Airframe S-64E AND S-64F ILLUSTRATED PARTS CATALOG Pub. No
Airframe S-64E AND S-64F ILLUSTRATED PARTS CATALOG Pub. No. 3EAC008 Manual Organization
The Illustrated Parts Catalog lists repair parts, airframe tools, test, measurement and diagnostic equipment.
A. Revision Record
B. List of Effective Pages
C. Table of Contents
D. Chapter Organization - Chapter titles are the same as the Maintenance Manual Chapters.
E. Alphanumeric Index
Rev. A Sept 18, 2007 2-

7. Airframe S-64E AND S-64F ILLUSTRATED PARTS CATALOG Pub. No
Airframe S-64E AND S-64F ILLUSTRATED PARTS CATALOG Pub. No. 3EAC008 Indention System
For proper identification of detail parts and next assemblies, listings are in the following indention system:
ASSEMBLY
ATTACHING PARTS FOR ASSEMBLY
-*-
SUBASSEMBLY
ATTACHING PARTS FOR SUBASSEMBLY
DETAIL PARTS
ATTACHING PARTS FOR DETAIL PARTS
The next higher assembly of any detail part may be determined by locating, in the next column to the left, excluding any attaching parts, the first item above the detail in question.
Rev. A Sept 18, 2007 2-

8. Airframe Model S-64F SERVICE BULLETINS
Manufacturer’s Service Bulletins
A. Service Bulletin Index - List of all Service Bulletins applicable to the S-64F Helicopter
B. Service Bulletin 64B General-1, TIME LIMITS - Retirement Schedule - List of all Life Limited Parts
C. Service Bulletin 64B General-2, MAJOR COMPONENTS - Maximum Recommended Time Between Overhauls
D. Service Bulletin Organization
1. Planning Information
2. Accomplishment Instructions
3. Material Information
Rev. A Sept 18, 2007 2-

9. Airframe MANUFACTURER’S PROGRESSIVE INSPECTION CHECKLIST
ZONE NO. 1: Cockpit All surfaces, material, components, and equipment located interior and exterior of the cockpit, electronics compartment, and overhead crawlway (attic) extending aft to the forward fuel cell bulkhead at station 248 and the aft pilot's cockpit)
ZONE NO. 2: Power Plant No. 1 and No. 2 power plants, (includes, but not limited to, the main engines, engine accessories, drive shafts.
ZONE NO. 3: Fuselage Sides and Bottom All surfaces, material, components, and equipment located interior and exterior of the fuselage right and left sides and bottom from fuselage STA 210 to 772 (includes, but not limited to, load levelers, hoist, pendant and cable, hoist well, bottom of main gear box and the cargo hook).
Rev. A Sept 18, 2007 2-

10. Airframe MANUFACTURER’S PROGRESSIVE INSPECTION CHECKLIST (Continued)
ZONE NO. 4: Fuselage Top All surfaces, material, components and equipment located above and including the top surface of the fuselage from STA 210 to 772 (includes, but not limited to, the upper portion of the main gear box, main rotor head and blades, hydraulic panels, auxiliary power plant and drive shafts).
ZONE NO. 5: Pylon All surfaces, material, components and equipment located interior and exterior aft of STA 772 (includes, but not limited to, horizontal stabilizer, tail rotor and blades, tail gear box, intermediate gear box and tail skid).
ZONE NO. 6: Main Landing Gear and Support Installation All surfaces, material, components and equipment located interior and exterior of the right and left main landing gears and support installations outboard from fuselage center section right and left sides.
Rev. A Sept 18, 2007 2-

11. Airframe IV. MANUFACTURER’S PROGRESSIVE INSPECTION CHECKLIST (Continued)
INTERVAL INSPECTIONS TO BE PERFORMED
Daily Walk around and special inspections as required.
15 Flight Hrs Safety Inspection of all zones.
30 Flight Hrs Phase I Inspection, Zone I - which includes Zone I Safety Inspection. Safety Inspection of all remaining zones.
45 Flight Hrs Safety Inspection of all zones.
60 Flight Hrs Phase II Inspection, Zone II - which includes Zone II Safety Inspection. Safety Inspection of all remaining zones.
75 Flight Hrs Safety Inspection of all zones.
90 Flight Hrs Phase III Inspection, Zone III - which includes Zone III Safety Inspection. Safety Inspection of all remaining zones.
105 Flight Hrs Safety Inspection of all zones.
120 Flight Hrs Phase IV Inspection, Zone IV - which includes Zone IV Safety Inspection. Safety Inspection of all remaining zones.
135 Flight Hrs Safety Inspection of all zones.
150 Flight Hrs Phase V Inspection, Zones V and VI - which includes Zones V and VI Safety Inspection. Safety Inspection of all remaining zones.
Rev. A Sept 18, 2007 2-

12. Pratt & Whitney Engine JFTD12B ENGINE MAINTENANCE MANUAL #435107 Manual Organization
A. Revision Record - Revision Service provided by P&W for a yearly fee.
B. List of Effective Pages
C. Table of Contents
D. Sections
Introduction
I. Tools
II. Maintenance
III. Periodic Inspection
IV. Preparation for Storage or Service
Appendix I. Consumable Materials
Appendix II. Lock Wiring
Rev. A Sept 18, 2007 2-

13. Pratt & Whitney Engine JFTD12A Engine ILLUSTRATED PARTS CATALOG #435109 Manual Organization
A. Revision Record
B. List of Effective Pages
C. Table of Contents
D. Sections
I. Introduction
II. Group Assembly Parts List
III. Numerical Index.
Rev. A Sept 18, 2007 2-

14. Pratt & Whitney Engine JFTD12A SERVICE BULLETINS
Manufacturer’s Service Bulletins
A. Service Bulletin Index
B. Service Bulletin # “Engine - Operating Time Between Overhauls, and Frequency of Combustion Area Inspections - Information Concerning”
C. Service Bulletin Organization
1. Planning Information
2. Accomplishment Instructions
3. Material Information
Rev. A Sept 18, 2007 2-

15. Optional Equipment Manual Organization
1. Revision Record
2. List of Effective Pages
3. Table of Contents
4. Chapter Organization
Chapter 1 - System Description & Operations
Chapter 2 - Installation
Chapter 3 - Inspection Guide Program
Chapter 4 - Removal Instructions
Chapter 5 - Field Maintenance Procedures
Chapter 6 - Troubleshooting
Chapter 7 - Illustrated Parts Breakdown
Appendix A - Wiring Diagrams
Appendix B - Hydraulic Schematics
Rev. A Sept 18, 2007 2-

16. S64F
Rev. A Sept 18, 2007 2-