1. Class F3P Indoor Aerobatic Power Model Aircrafts
Final Schedule F3P – AF-19 ( )

3. ( not judged, not scored )
Take-off procedure
( not judged, not scored )
Explainations:
Aircraft upright
Aircraft inverted
Aircraft in Knife Edge
Safety line

4. AF-19.01 Double Key with ¼ roll, ¼ roll, ¼ roll, ¼ roll
From upright, pull through a ¼ loop into a vertical upline, perform a ¼ roll, perform a 5/8 knife-edge loop into a 45°downline, perform a ¼ roll, push through a ¼ loop into a 45° upline, perform a ¼ roll, perform a 5/8 knife edge loop into a vertical down-line, perform a ¼ roll, pull through a ¼ loop, exit upright.
F3P-AF

5. AF-19.01 Double Key with ¼ roll, ¼ roll, ¼ roll, ¼ roll
During Knife Edge the wing must be in the vertical plane.
¼ rolls on middle of the lines.
All radii are equal.
F3P-AF

6. AF-19.01 Double Key with ¼ roll, ¼ roll, ¼ roll, ¼ rollor
From upright, pull through a ¼ loop into a vertical upline, perform a ¼ roll, perform a 5/8 knife-edge loop into a 45°downline, perform a ¼ roll, push through a ¼ loop into a 45° upline, perform a ¼ roll, perform a 5/8 knife edge loop into a vertical down-line, perform a ¼ roll, pull through a ¼ loop, exit upright.
F3P-AF

7. AF-19.01 Double Key with ¼ roll, ¼ roll, ¼ roll, ¼ roll
During Knife Edge the wing must be in the vertical plane.
¼ rolls on middle of the lines.
All radii are equal. or
F3P-AF

8. According to the manoeuvre describtion the manoeuvre may be flown with with different length of the center vertical up and downlines.
F3P-AF

9. AF-19.02 Shark Fin with four consecutive 1/8 rolls, ½ roll, ½ roll
From upright, pull through a 1/8 loop loop into a 45° upline, perform consecutively four 1/8 rolls, pull through a 3/8 loop into a vertical downline, perform a ½ roll, push through a ¼ loop, perform a ½ roll, exit upright.
F3P-AF

10. AF-19.02 Shark Fin with four consecutive 1/8 rolls, ½ roll, ½ roll
1/8 rolls centered on middle of the line.
1/8
1/8
1/8
1/8
45°
All radii are equal.
Lines between (part) rolls must be short and of equal recognizeable length.
½ roll on middle of the line.
F3P-AF

11. AF-19.03 Three consecutive opposite rolls
From upright, perform three consecutive rolls in opposite direction, exit upright.
F3P-AF

12. AF-19.03 Three consecutive opposite rolls
Rolls must have the same roll rate.
Between rolls in opposite direction there must be no line.
F3P-AF

13. AF-19. 04 Knife Edge Humpty Bump with two consecutive
AF Knife Edge Humpty Bump with two consecutive opposite ¼ rolls, ½ roll integrated, ½ roll
½ roll integrated
¼ roll
¼ roll
½ roll
From upright, pull through a ¼ loop into a vertical upline, perform consecutively two ¼ rolls in opposite direction, perform a ½ knife-edge loop, while integrating a ½ roll, perform a ½ roll, pull through a ¼ loop, exit upright.
F3P-AF

14. AF-19. 04 Knife Edge Humpty Bump with two consecutive
AF Knife Edge Humpty Bump with two consecutive opposite ¼ rolls, ½ roll integrated, ½ roll
½ roll integrated
The ½ roll must be integrated on circular flightpath of the ½ knife edge loop.
¼ rolls and ½ roll on middle of the line lines.
All radii are equal.
The Manoeuvre may be flown to the outside, too!
F3P-AF

15. AF-19.05 Two Loops with opposite rolls integrated
roll integrated
Loop 1
From upright, pull through a loop while performing a roll integrated, ...
F3P-AF

16. AF-19.05 Two Loops with opposite rolls integrated
roll integrated
Loop 2
... pull through another loop, while performing a roll integrated in opposite direction, exit upright.
F3P-AF

17. AF-19.05 Two Loops with opposite rolls integrated
The loops must be round.
The rolls must be integrated on circular flightpath of the loops.
Roll reversal must be immediate.
F3P-AF

18. AF-19.06 Tail Slide with ½ roll
From upright, pull through a ¼ loop into a vertical upline, perform a ½ roll, perform a tail slide (canopy up) into a vertical downline pull through a ¼ loop, exit upright.
F3P-AF

19. AF-19.06 Tail Slide with ½ roll
Flipover = 0 points.
½ roll on middle of the line.
All radii are equal.
F3P-AF

20. AF Figure N with ¼ roll, ¼ circle, two consecutive ¼ rolls, two ½ rolls integrated in the corners, two consecutive ¼ rolls, ¼ circle, ¼ roll
¼ roll
½ roll integrated
¼ roll
¼ roll
¼ roll
¼ roll
½ roll integrated
¼ roll
From upright, perform a ¼ roll in the centre, perform a sustained knife-edge flight, perform a ¼ knife-edge circle into crossbox knife edge-flight, perform two consecutive ¼ rolls, perform a 3/8 knife-edge circle while integrating a ½ roll outside into a knife edge-flight on 45˚, perform a 3/8 knife-edge circle while integrating a ½ roll outside, into a crossbox knife edge-flight, perform two consecutive ¼ rolls, perform a ¼ knife-edge circle, perform a ¼ roll, exit upright.
F3P-AF

21. AF Figure N with ¼ roll, ¼ circle, two consecutive ¼ rolls, two ½ rolls integrated in the corners, two consecutive ¼ rolls, ¼ circle, ¼ roll
During Knife Edge the wing must be in the vertical plane.
Integrated rolls must be outside.
Lines between part rolls must be short and of equal recognizable length.
¼ rolls centered on middle of the line.
All radii are equal.
F3P-AF

22. AF-19.08 Knife Edge Humpty Bump with ¼ roll, ¼ roll
From upright, pull through a 3/8 loop into a 45° upline, perform a ¼ roll, perform a ½ knife-edge loop into a 45° downline, per-form a ¼ roll, pull through a 3/8 loop, exit upright.
F3P-AF

23. AF-19.08 Knife Edge Humpty Bump with ¼ roll, ¼ roll
During Knife Edge the wing must be in the vertical plane.
45°
¼ rolls on middle of the line.
All radii are equal.
F3P-AF

24. AF-19.08 Knife Edge Humpty Bump with ¼ roll, ¼ rollor
From upright, pull through a 3/8 loop into a 45° upline, perform a ¼ roll, perform a ½ knife-edge loop into a 45° downline, per-form a ¼ roll, pull through a 3/8 loop, exit upright.
F3P-AF

25. AF-19.08 Knife Edge Humpty Bump with ¼ roll, ¼ roll
During Knife Edge the wing must be in the vertical plane.
45°
¼ rolls on middle of the line.
All radii are equal. or
F3P-AF

26. AF-19. 09 Vertical Square Eight with consecutive ¼ torque roll,
AF Vertical Square Eight with consecutive ¼ torque roll, opposite ½ torque roll, ½ roll, roll, consecutive ½ torque roll, opposite ¼ torque roll
½ roll
¼ torque roll
½ torque roll
½ torque roll
¼ torque roll
½ roll
From upright, fly past centre, pull through a ¼ loop into a vertical upline, perform consecutively a ¼ torque roll and a, ½ torque roll in opposite direction, perform a ¼ knife loop, perform a ½ roll, perform a ¼ knife-edge loop into a vertical downline, perform a ¼ knife loop, perform a ½ roll, perform a ¼ knife-edge loop into a vertical upline, perform consecutively a ½ torque roll and a, ¼ torque roll in opposite direction, push through a ¼ loop, exit upright
F3P-AF

27. AF-19. 09 Vertical Square Eight with consecutive ¼ torque roll,
AF Vertical Square Eight with consecutive ¼ torque roll, opposite ½ torque roll, ½ roll, roll, consecutive ½ torque roll, opposite ¼ torque roll
½ rolls on middle of the line.
¼ T
½ T
½ T
¼ T
Torque rolls centered on middle of the line.
All radii are equal.
All radii are equal.
F3P-AF

28. AF-19. 10 Half Hourglass with two consecutive ¼ rolls, roll, two
AF Half Hourglass with two consecutive ¼ rolls, roll, two consecutive ¼ rolls
¼ roll
roll
Part 1
¼ roll
From upright, push though a 1/8 loop into a 45° downline, perform consecutively two ¼ rolls, push through a 3/8 loop into a vertical upline, perform a roll, ...
F3P-AF

29. AF-19. 10 Half Hourglass with two consecutive ¼ rolls, roll, two
AF Half Hourglass with two consecutive ¼ rolls, roll, two consecutive ¼ rolls
¼ roll
¼ roll
Part 2
... push through a 3/8 loop into a 45° downline, perform consecutively two ¼ rolls, push through a 1/8 loop, exit inverted.
F3P-AF

30. AF-19. 10 Half Hourglass with two consecutive ¼ rolls, roll, two
AF Half Hourglass with two consecutive ¼ rolls, roll, two consecutive ¼ rolls
Lines between part rolls must be short and of equal recognizable length.
45°
¼ rolls centered on middle of the line.
Roll on middle of the line.
All radii are equal.
All radii are equal.
F3P-AF

31. AF-19. 11 Figure Z with two consecutive 1/8 rolls, two consecutive
AF Figure Z with two consecutive 1/8 rolls, two consecutive ¼ rolls, two consecutive 1/8 rolls
1/8 roll
1/8 roll
¼ roll
¼ roll
1/8 roll
1/8 roll
From inverted, perform consecutively two 1/8 rolls, perform a 3/8 knife-edge loop into a 45° upline, perform consecutively two ¼ rolls, perform a 3/8 knife edge loop, perform consecutively two 1/8 rolls, exit upright.
F3P-AF

32. AF-19. 11 Figure Z with two consecutive 1/8 rolls, two consecutive
AF Figure Z with two consecutive 1/8 rolls, two consecutive ¼ rolls, two consecutive 1/8 rolls
1/8
1/8
¼ rolls centered on middle of the line.
Lines between part rolls must be short and of equal recognizable length.
45°
1/8
1/8
All radii are equal.
F3P-AF

33. ( not judged, not scored )
Landing sequence
( not judged, not scored )
Forget WHO is flying (friend, rival, countryman, flier from other nation)
Forget WHAT is flying
LOOK ONLY AT LINES DESCRIBED .... (and the precision, smoothness, positioning, and size)
Safety line
© Peter Uhlig, December 2017